Ford 2007 Expedition инструкция обслуживания

Introduction 4 Instrument Cluster 12 W arning lights and chimes 12 Gauges 18 Entertainment Systems 21 How to get going 21 AM/FM stereo with CD 25 AM/FM stereo with in-dash six CD 31 Auxiliary input jack (Line in) 38 Rear seat controls 39 Satellite radio information 44 Family entertainment system 47 Navigation system 73 Climate Controls 74 Manual he[...]

Locks and Security 145 Keys 145 Locks 145 Seating and Safety Restraints 161 Seating 161 Safety restraints 178 Airbags 192 Child restraints 201 Tires, Wheels and Loading 217 T ire information 219 T ire inflation 221 T ire Pressure Monitoring System (TPMS) 234 V ehicle loading 238 T railer towing 244 Recreational towing 251 Driving 253 Starting 253 B[...]

Customer Assistance 314 Reporting safety defects (U.S. only) 321 Reporting safety defects (Canada only) 321 Cleaning 322 Maintenance and Specifications 329 Engine compartment 331 Engine oil 334 Battery 337 Engine coolant 339 Fuel information 345 Air filter(s) 357 Part numbers 360 Maintenance product specifications and capacities 362 Engine data 366[...]

CALIFORNIA Proposition 65 W arning W ARNING: Engine exhaust, some of its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. In addition, certain fluids contained in vehicles and certain products of component wear contain or emit chemic[...]

SAFETY AND ENVIRONMENT PROTECTION W arning symbols in this guide How can you reduce the risk of personal injury to yourself or others? In this guide, answers to such questions are contained in comments highlighted by the warning triangle symbol. These comments should be read and observed. W arning symbols on your vehicle When you see this symbol, i[...]

BREAKING-IN YOUR VEHICLE Y our vehicle does not need an extensive break-in. T ry not to drive continuously at the same speed for the first 1,000 miles (1,600 km) of new vehicle operation. V ary your speed frequently in order to give the moving parts a chance to break in. Drive your new vehicle at least 500 miles (800 km) before towing a trailer . A[...]

Service Data Recording Service data recorders in your vehicle are capable of collecting and storing diagnostic information about your vehicle. This potentially includes information about the performance or status of various systems and modules in the vehicle, such as engine, throttle, steering or brake systems. In order to properly diagnose and ser[...]

Using your vehicle with a snowplow Do not use this vehicle for snowplowing. Y our vehicle is not equipped with a snowplowing package. Notice to owners of pickup trucks and utility type vehicles Utility vehicles have a significantly higher rollover rate than other types of vehicles. Before you drive your vehicle, please read this Owner’ s Guide ca[...]

Export unique (Non–United States/Canada) vehicle specific information For your particular global region, your vehicle may be equipped with features and options that are different from the ones that are described in this Owner’ s Guide. A market unique supplement may be supplied that complements this book. By referring to the market unique suppl[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Airbag - Front Airbag - Side Child Seat Child Seat Installation W arning Child Seat Lower Anchor Child Seat T ether Anchor Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based Powertrain Malfuncti[...]

V ehicle Symbol Glossary Power W indows Front/Rear Power W indow Lockout Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Corr[...]

W ARNING LIGHTS AND CHIMES W arning lights and gauges can alert you to a vehicle condition that may become serious enough to cause expensive repairs. A warning light may illuminate when a problem exists with one of your vehicle’ s functions. Many lights will illuminate when you start your vehicle to make sure the bulb works. If any light remains [...]

Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , the fuel system, interior floor coverings or other vehicle components, possibly causing a fire. Powertrain malfunction/reduced power (R TT) (if equipped): Displays when the engine has defaulted to a ’limp-home’ operation. Report the fault to a[...]

Airbag readiness: If this light fails to illuminate when ignition is turned to ON, continues to flash or remains on, have the system serviced immediately by your authorized dealer . A chime will also sound when a malfunction in the supplemental restraint system has been detected. Safety belt: Reminds you to fasten your safety belt. A Belt-Minder ?[...]

Low tire pressure warning (if equipped): Illuminates when your tire pressure is low . If the light remains ON at start up or while driving, the tire pressure should be checked. Refer to Inflating Y our T ires in the T ires, Wheels and Loading chapter . When the ignition is first turned to ON, the light will illuminate for 3 seconds to ensure the bu[...]

Speed control: Illuminates when the speed control is activated. T urns off when the speed control system is deactivated. Four wheel drive low (R TT) (if equipped): Displays when four -wheel drive low is engaged. If the light fails to illuminate when the ignition is turned ON, or remains on, have the system serviced immediately by your authorized de[...]

High beams: Illuminates when the high beam headlamps are turned on. Key-in-ignition warning chime (if equipped): Sounds when the key is left in the ignition in the OFF/LOCK or ACCESSORY position and the driver’ s door is opened. Headlamps on warning chime: Sounds when the headlamps or parking lamps are on, the ignition is off (the key is not in t[...]

GAUGES Speedometer: Indicates the current vehicle speed. Engine coolant temperature gauge: Indicates engine coolant temperature. At normal operating temperature, the needle will be in the normal range (between “H” and “C”). If it enters the red section, the engine is overheating. Stop the vehicle as soon as safely possible, switch off the e[...]

Odometer: Registers the total miles (kilometers) of the vehicle. • W ith Standard Message Center • W ith Optional Message Center Refer to Message Center in the Driver Controls chapter on how to switch the display from Metric to English. T rip odometer: Registers the miles (kilometers) of individual journeys. • W ith Standard Message Center Pr[...]

Battery voltage gauge: Indicates the battery voltage when the ignition is in the ON position. If the pointer moves and stays outside the normal operating range, have the vehicle’ s electrical system checked by your authorized dealer as soon as possible. Engine oil pressure gauge: Indicates engine oil pressure. The needle should stay in the normal[...]

AUDIO SYSTEMS Quick start — How to get going Listening to the radio 1. If the audio system is off, press VOL-PUSH to turn the radio on. T urn VOL-PUSH to adjust the volume. Note: The system may take a few moments to turn on. 2. Press AM/FM repeatedly to choose between AM/FM1/FM2 frequency bands. 3. Press / to manually go up/down the frequency ban[...]

Listening to satellite radio (if equipped) 1. If the audio system is turned off, press VOL-PUSH to turn the radio on. T urn VOL-PUSH to adjust the volume. Note: The system may take a few moments to turn on. 2. Press AUX repeatedly to cycle through auxiliary audio sources. Select SA T1, SA T2 or SA T3 to listen to satellite radio. 3. Press SEEK, SEE[...]

For a single CD system, if a disc is not already loaded, insert only one, label side up into the CD slot. LOADING CD and READING DISC will appear in the display . The first track on the disc will begin playing. For an in-dash six CD system, if a disc is not already loaded, press LOAD. Select a slot number using memory presets 1–6. When the displa[...]

Press SHUFFLE to engage shuffle mode. SHUFFLE ON will appear in the display . If you wish to engage shuffle mode right away , press SEEK to begin random play . Otherwise, random play will begin when the current track is finished playing. CD SHUF will appear in the display . T o disengage, press SHUFFLE again. SHUFFLE OFF will appear in the display [...]

AM/FM single CD/MP3 satellite compatible sound system (if equipped) Accessory delay: Y our vehicle is equipped with accessory delay . W ith this feature, the window switches, radio and moon roof (if equipped) may be used for up to ten minutes after the ignition is turned off or until either front door is opened. 1. / (T uner): In radio mode, press [...]

3. MENU: Press repeatedly to access the following settings: CA TEGOR Y (satellite radio if equipped): When satellite radio mode is active, press MENU until the currently active category appears in the display (CA TEGORY MODE). In CA TEGOR Y MODE, press / to scroll through the list of available SIRIUS channel Categories (Pop, Rock, News, etc.) Once [...]

SPEEDVOL (Speed sensitive volume): Press MENU to reach the SPEEDVOL setting. Radio volume automatically gets louder with increasing vehicle speed to compensate for road and wind noise. Use / / SEEK, SEEK to adjust. The default setting is off; increasing your vehicle speed will not change the volume level. Adjust 1–7: Increasing this setting from [...]

5. SEEK : In radio mode, press / to access the previous/next strong station. In CD/MP3 mode, press / to access the previous/next CD/MP3 track. In satellite radio mode (if equipped), press SEEK, SEEK to seek to the previous/next channel. In CA TEGOR Y MODE, press SEEK, SEEK to select a category (Jazz, Rock, News, etc.). Once the desired category is [...]

8. FOLDER : In folder mode, press FOLDER to access next folder on MP3 discs, if available. 9. FOLDER: In folder mode, press FOLDER to access the previous folder on MP3 discs, if available. 10. FF (Fast forward): Press FF to manually advance in a CD/MP3 track. 11. REW (Rewind): Press REW to manually reverse in a CD/MP3 track. 12. Memory presets: T o[...]

In satellite radio mode (if equipped), press and release to enter TEXT MODE and display the current song title. While in TEXT MODE, press again to scroll through the current song title, artist, channel category and the SIRIUS long channel name. Press and hold to hear a brief sampling of the next channels. Press again to stop. In CA TEGOR Y MODE, pr[...]

Premium/Audiophile AM/FM in-dash six CD/MP3 satellite compatible sound system (if equipped) Accessory delay: Y our vehicle is equipped with accessory delay . W ith this feature, the window switches, radio and moon roof (if equipped) may be used for up to ten minutes after the ignition is turned off or until either front door is opened. 1. / (T une/[...]

3. MENU: Press repeatedly to access to the following settings: CA TEGOR Y (satellite radio if equipped): When satellite radio is active, press MENU until the currently active category appears in the display (CA TEGORY MODE). In CA TEGOR Y MODE, press / to scroll through the list of available SIRIUS channel Categories (Pop, Rock, News, etc.) Press S[...]

T o view the station name or type: W ith RBDS ON, press TEXT/SCAN to toggle between displaying the station type (COUNTRY , ROCK, etc.) or the station name (WYCD, WXYZ, etc.). BASS: Press MENU to reach the bass setting. Use / / SEEK, SEEK to adjust. TREB (T reble): Press MENU to reach the treble setting. Use / / SEEK, SEEK to adjust. BAL (Balance): [...]

COMPRESS (Compression): A vailable only in CD/MP3 mode. Press MENU until COMPRESS ON/OFF appears in the display . Use / / SEEK, SEEK to toggle ON/OFF . When COMPRESS is ON, the system will bring soft and loud CD passages together for a more consistent listening level. Single Play/Dual Play: If Single Play is ON, press / for Dual Play . For further [...]

6. (Play/Pause): This control is operational in CD and DVD mode (if equipped). When a CD or DVD is playing in the FES system, press this control to play or pause the current CD/DVD. The CD/DVD status will display in the radio display . If your vehicle is equipped with a Family Entertainment System (FES), please refer to Family entertainment DVD sys[...]

In satellite radio mode (if equipped), there are 18 available presets, six each for SA T1, SA T2 and SA T3. T o save satellite channels in your memory presets, tune to the desired channel then press and hold a preset control until sound returns. Satellite radio is available only with a valid SIRIUS subscription. Check with your authorized dealer fo[...]

17. LOAD: T o load a disc into the system, press LOAD. Select a slot number using memory presets 1–6. When the display reads LOAD CD#, load the desired disc, label side up. If you do not choose a slot within 5 seconds, the system will choose for you. Once loaded, the first track will begin to play . T o auto load up to 6 discs, press and hold LOA[...]

Auxiliary input jack (Line in) Y our vehicle is equipped with an Auxiliary Input Jack (AIJ). The Auxiliary Input Jack provides a way to connect your portable music player to the in-vehicle audio system. This allows the audio from a portable music player to be played through the vehicle speakers with high fidelity . T o achieve optimal performance, [...]

compatible with the AIJ. The AIJ will only work correctly with devices that have a headphone output with a volume control. 2. Do not set the portable music player’ s volume level higher than is necessary to match the volume of the CD or FM radio in your audio system as this will cause distortion and will reduce sound quality . Many portable music[...]

3. : In radio mode, press and release to scroll through memory presets. Press and hold to seek to the next station. In CD mode, press and release to advance to the next track. Press and hold to fast forward within that track. 4. W ired headphone jacks 5. : In radio mode, press and release to scroll through memory presets. Press and hold to seek to [...]

• Use the other controls to make adjustments to the playing media. • Dual Play mode may also be activated by pressing memory presets 2 and 4 simultaneously on the front audio controls. The rear speakers mute and rear seat passengers have audio (for their selected media) available through their headphones. Using headphones/Dual Play mode Do not [...]

GENERAL AUDIO INFORMATION Radio frequencies: AM and FM frequencies are established by the Federal Communications Commission (FCC) and the Canadian Radio and T elecommunications Commission (CRTC). Those frequencies are: AM: 530, 540–1700, 1710 kHz FM: 87.7, 87.9–107.7, 107.9 MHz Radio reception factors: There are three factors that can affect ra[...]

CD units are designed to play commercially pressed 4.75 in (12 cm) audio compact discs only . Due to technical incompatibility , certain recordable and re-recordable compact discs may not function correctly when used in Ford CD players. Do not use any irregular shaped CDs or discs with a scratch protection film attached. CDs with homemade paper (ad[...]

• Creating discs with only one level of folders will help with navigation through the disc files. Sample MP3 structure If you are burning your own MP3 discs, it is important to understand how the system will read the structures you create. While various files may be present, (files with extensions other than mp3), only files with the .mp3 extensi[...]

• Antenna obstructions: For optimal reception performance, keep the antenna clear of snow and ice build-up and keep luggage and other material as far away from the antenna as possible. • T errain: Hills, mountains, tall buildings, bridges, tunnels, freeway overpasses, parking garages, dense tree foliage and thunderstorms can interfere with your[...]

Radio Display Condition Action Required ACQUIRING Radio requires more than two seconds to produce audio for the selected channel. No action required. This message should disappear shortly . SA T F AUL T Internal module or system failure present. If this message does not clear within a short period of time, or with an ignition key cycle, your receiv[...]

Radio Display Condition Action Required NO TEXT Song title information not available. Song title information not available at this time on this channel. The system is working properly . NO TEXT Category information not available. Category information not available at this time on this channel. The system is working properly . NO SIGNAL Loss of sign[...]

Quick start Y our Family Entertainment System includes a DVD system, two sets of wireless infrared (IR) headphones and a wireless infrared (IR) remote control. T o play a DVD in the DVD system: The DVD system can play DVD-Video, DVD-R, DVD-R/W discs as well as audio CDs and video CDs. T o ensure proper disc operation, check the disc for finger prin[...]

1. Ensure that the vehicle ignition is in the RUN or ACCESSORY position. 2. Insert a CD into the system, label-side up to turn on the DVD system. It will load and automatically begin to play . If there is already a CD in the system, press PLA Y on the DVD player . 3. The disc will begin to play and the ’CD Audio Disc’ screen will display . From[...]

2. Press the power button to turn the DVD system on. The indicator light next to the power button will illuminate. 3. Connect an auxiliary audio/video source by connecting RCA cords (not included) to the RCA jacks on the left hand side of the system. • Y ellow (1) — video input • White (2) — left channel audio input • Red (3) — right ch[...]

Note: Channel A can access any possible media source (AM, FM1, FM2, SA T (if equipped), CD, DVD, AUX). Channel B can only access DVD and AUX sources. Note: Refer to Single play/Dual play for more information. Using the infrared (IR) wireless headphones: 1. Press the power control on the earpiece to turn the headphones ON. 2. Select Channel A or B f[...]

DVD player controls 1. Headphone control A/B: Press to select either the A or B headphone source. Then press MEDIA to select the desired playing media for that headset. When a headphone channel has been selected (A or B), selections will affect the source on that channel only . Note: Headphone A can access any possible media (AM, FM1, FM2, SA T (if[...]

4. (Fast forward): Press and release for the next chapter or track. Press and hold to forward search a DVD, Video CD, or FES CD in DVD/CD mode. 5. / (Play/Pause): Press (Play) to select DVD mode (and to turn the DVD system on if it is off). If a disc is present, it will resume or begin to play . Press (Pause) while playing a disc to pause a DVD or [...]

11. / (Headphones/Speakers): Press once for Dual Play (Headphone mode- the rear speakers are muted) and press again for Single Play (same media playing through all speakers). For further interaction information, refer to Single Play/Dual play . 12. MEDIA: Press repeatedly to select from the various possible playing media sources (AM, FM1, FM2, SA T[...]

Remote control Unless otherwise stated, all operations can be carried out with the remote control. Always point the remote control directly at the player . Ensure that there are no obstructions between the remote and player . 1. Power control: Press to turn the FES (Family Entertainment System) ON/OFF . 2. Cursor controls: Use in various active men[...]

7. VOL (V olume): When in Single Play , press to increase ( )o r decrease ( ) the volume over all speakers. When in Dual Play , press to increase ( ) or decrease ( ) the volume for the wired headphones. (W ireless headphone volume is controlled with the rotary dial on the right ear piece.) 8. Fast Forward/Next: In DVD mode, press and hold for a qui[...]

22. ENTER: Press to select the highlighted menu option. 23. ILLUMINA TION : Press to illuminate the remote control and backlight all of the buttons. Battery replacement Batteries are supplied with the remote control unit. Since all batteries have a limited shelf life, replace them when the unit fails to control the DVD player . Remove the screw and[...]

Headphones Wireless headphones Y our FES system is equipped with two sets of battery powered, infrared wireless headphones. T wo AAA batteries are needed to operate the headphones. (Batteries are included.) Additional infrared wireless headphones may be purchased for use with the system. Also, wired headphones may be purchased and plugged in where [...]

T o operate the headphones: • Press ON/OFF on the ear piece to turn on the headphones. A red indicator light will illuminate indicating the headphones are ON. Press ON/OFF again to turn the headphones off. • Adjust the headphones to comfortably fit your head using the headband adjustment. • Select the desired audio source (Channel A or B) for[...]

Channel A source. The wired headphone jack for Channel B is located on the right side of the FES and is labeled B. Headphones plugged into this headphone jack will hear audio from the audio source selected to be the Channel B source. Adjust the headphone volume using the volume control on the DVD system. Operation Single play/Dual play Y our DVD an[...]

Press the Headphone Control button A to change the audio source for Channel A. Press MEDIA to change the audio source for Channel A. This information will display on the DVD system screen. Press the Headphone Control button B to change the audio source for Channel B. Press MEDIA to change the audio source for Channel B. This information will displa[...]

Menu mode Press MENU once on the DVD system to access the DVD disc menu if available. Press MENU twice to access the DVD set-up menu and the following features: 1. ZOOM 2. ANGLE 3. ASPECT RA TIO 4. LANGUAGE 5. SUB TITLES Angle mode Select ANGLE to select various angles of view for the DVD. This is disc dependent — some DVD discs may have more vie[...]

Y ou can select from: WIDE, LETTER BOX or P AN SCAN. Once you have made your selection, press ENTER to confirm. The LCD screen display will immediately change to your selection after the system resumes playback of the DVD. The system default is WIDE (16:9). This is disc dependent. Language Select LANGUAGE to select the language you would like to us[...]

Once you have made your selection, press ENTER to confirm. This is disc dependent. Audio CDs T o play audio CDs on your DVD system: 1. Ensure that the vehicle ignition is in the RUN or ACCESSORY position. 2. Ensure that the DVD system is ON. 3. Insert an audio CD into the DVD system, label side up. 4. The track and elapsed time will appear in the s[...]

4. The folder , track and elapsed time will appear in the status bar . The screen will list the Artist, T itle, Album and File Name. COMP (Compression): Compression brings soft and loud CD/MP3 passages together for a more consistent listening level when in CD mode. Press to turn the feature ON/OFF SHUFFLE: Press to hear all tracks on the current MP[...]

CD, MP3 and CD player care • Handle discs by their edges only . Never touch the playing surface. • Do not expose discs to direct sunlight or heat sources for extended periods of time. • Do not insert more than one disc into the slot of the CD player (if equipped). • Always store discs out of direct sunlight. Excessive heat may damage or war[...]

4. Use the DVD bezel controls to: Press to play or pause a DVD. Press to stop or eject a DVD. Press and release to go to the previous chapter . Press and hold for a fast reverse search. Press and release to go to the next chapter . Press and hold for a fast forward search. Press when not in menu mode to adjust brightness, or when in menu mode to na[...]

Frame by frame 1. W ith a DVD playing, press pause. 2. Press the right cursor button. The DVD will advance one frame. Each press of the right cursor button will advance the DVD video by one frame. Headphone/auxiliary jacks There are wired headphones (not included) and auxiliary jacks on the left and right side of your DVD system. They can be used t[...]

The B headphone jack (5) is located on the right side of the DVD system. Plug in wired headphones (not included) here. Note: The B headphones can only access DVD and AUX modes. They cannot access radio sources. Audio displays Y our DVD system interacts closely with the front audio system. Status messages will appear in the radio display showing the[...]

The three states are described as: FULL (enabled): The FES has control over the primary (speaker) and secondary (headphone) audio sources. LOCAL : The FES has control over the secondary source (headphones) only . The radio will ignore button presses that affect the primary (speaker) audio source. LOCKED (disabled): The FES buttons are locked and al[...]

Do not leave children unattended in the vehicle and do not let children operate the system while unsupervised. If wired headphones or auxiliary systems are used, children may become entangled in the cords and seriously injure themselves. The front glass on the liquid crystal display (LCD) flip-down screen may break when hit with a hard surface. If [...]

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference and radio communications[...]

onto the media controls or into the system. If liquid is accidentally spilled onto the system, immediately turn the system OFF and consult a qualified service technician. Cleaning the liquid crystal display (LCD) flip-down screen Clean the display screen by applying a small amount of water or any ammonia-based household glass cleaner directly to a [...]

MANUAL HEATING AND AIR CONDITIONING SYSTEM (IF EQUIPPED) 1. T emperature selection: Controls the temperature of the airflow in the vehicle. 2. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recirculated air through the instrument panel vents [...]

6. Fan speed adjustment: Controls the volume of air circulated in the vehicle. Manual heating and air conditioning system with rear passenger compartment climate control (if equipped) 1. Air flow selections: Controls the direction of the airflow in the vehicle. See the following for a brief description on each control. MAX A/C: Distributes recircul[...]

with the front control. The rear cabin airflow temperature will match the driver airflow temperature setting when only the center rear temperature light ( REAR ) is illuminated. The rear cabin airflow temperature will be warmer or cooler than the driver airflow temperature setting when more than one rear temperature light ( REAR )i s illuminated. 5[...]

T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the middl[...]

than the driver airflow temperature setting when more than one rear temperature bar ( REAR ) is illuminated. 3. Passenger temperature control: Press to increase/decrease the temperature for the passenger in the front of the vehicle. 4. R Rear defroster: Press to activate/deactivate the rear window defroster . Refer to Rear window defroster later in[...]

16. AUTO: Press to engage full automatic operation, and select the desired temperature using the temperature control. The system will automatically determine fan speed, airflow location, A/C on or off, and outside or recirculated air , to heat or cool the vehicle to reach the desired temperature. 17. EXT : Press to display the outside temperature. [...]

4. R Rear defroster: Press to activate/deactivate the rear window defroster . Refer to Rear window defroster later in this chapter for more information. 5. R Rear fan speed control: Press to enable the auxiliary system or to adjust the rear fan speed from the front control. The rear fan speed settings available are 4, 3, 2, 1 and O (OFF). 6. Passen[...]

14. Driver temperature control: Press to increase or decrease the temperature on the driver side of the cabin. Sets the passenger side temperature also when DUAL is disengaged. Note: The recommended vehicle cabin setting is between 72°F (22°C) and 75°F (24°C). 15. AUTO: Press to engage full automatic operation, and select the desired temperatur[...]

T o aid in side window defogging/demisting in cold weather: 1. Select . 2. Select A/C. 3. Adjust the temperature control to maintain comfort. 4. Set the fan speed to the highest setting. 5. Direct the outer instrument panel vents towards the side windows. T o increase airflow to the outer instrument panel vents, close the vents located in the middl[...]

HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to turn on the headlamps. Autolamp control The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights [...]

High beams Push the lever toward the instrument panel to activate. Pull the lever towards you to deactivate. Flash to pass Pull toward you slightly to activate and release to deactivate. Daytime running lamps (DRL) (if equipped) T urns the foglamps on at full intensity output. T o activate: • the ignition must be in the ON position and • the he[...]

P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel and all applicable switches in the vehicle during headlamp and parklamp operation. Move the control to the full upright position, past detent, to turn on the interior lamps. Move the control to the full down position, past detent, to prevent the interior lights from illumina[...]

4. On the wall or screen you will observe a light pattern with a distinct horizontal edge towards the right. If this edge is not at the horizontal reference line, the beam will need to be adjusted so the edge is at the same height as the horizontal reference line. 5. Locate the vertical adjuster on each headlamp, then use a Phillips #2 screwdriver [...]

INTERIOR LAMPS Front row map lamps (if equipped) T o turn on the map lamps, press the outer edge of the clear lens. The front row map lamp lights when: • any door is opened. • the instrument panel dimmer switch is rotated until the courtesy lamps come on. • the remote entry controls are pressed and the ignition is OFF . Front row map/dome lam[...]

Rear cargo lamp The dome lamp lights when: • any door is opened, and the switch is in the middle position. • the instrument panel dimmer switch is rotated until the courtesy lamps come on. • any of the remote entry controls are pressed and ignition is OFF (and switch is in the middle position). W ith the ignition key in the ACC or ON position[...]

Function Number of bulbs T rade number Front park/turn lamps 2 3157 A Foglamps 2 9145 Front row map lamps 2 W5W Front row map/dome lamps 3 578 Rear cargo lamp 1 578 2nd row reading lamp 2 W5W T urn/tail/brake/ sidemarker lamps 2 3157K or 4157K Backup lamp 2 921 Approach/mirror turn signal lamps (if equipped) 2 906 Mirror approach lamps – non turn[...]

3. At the back of the headlamp, remove the two headlamp assembly retainer bolts. 4. Slide headlamp assembly forward and off the retaining tab to expose the back of the bulb and electrical connector . 5. Disconnect the electrical connector . 6. Remove the bulb by turning it counterclockwise and then pulling it straight out. Handle a halogen headlamp[...]

Replacing front parking lamp/turn/sidemarker signal bulbs 1. Make sure that the headlamp control is in the OFF position. 2. Open the hood. 3. At the back of the headlamp, remove the two headlamp assembly retainer bolts. 4. Slide headlamp assembly forward and off the retaining tab to expose the back of the headlamp assembly . 5. Rotate the bulb sock[...]

4. Rotate the bulb socket counterclockwise and remove from lamp assembly . 5. Pull bulb straight out of socket and snap in the new bulb. 6. Install the bulb socket into the lamp assembly and rotate clockwise. 7. Carefully install the tail lamp assembly on the vehicle by securing the lamp assembly with two torx screws. High-mount brakelamp T o chang[...]

Replacing license plate lamp bulb The license plate bulbs are located in the license plate housing assembly on the liftgate. T o change the license plate bulbs: 1. Make sure the headlamp switch is in the OFF position. 2. Remove the license lamp screw from the assembly . 3. Pull the lamp down and twist the bulb socket counterclockwise. Remove the bu[...]

Approach lamp bulb removal (if equipped) T o change the bulbs: 1. Make sure that all the doors are closed and the interior lights have automatically turned off or the opposite mirror approach lamp has turned off. 2. W ith a small flat tipped screwdriver , insert the tip into the approach light module slot located on the outboard corner of the lens [...]

MULTI-FUNCTION LEVER W indshield wiper: Rotate the end of the control away from you to increase the speed of the wipers; rotate towards you to decrease the speed of the wipers. Speed dependent wipers: When the wiper control is on, the speed of the wipers will automatically adjust with the vehicle speed. The faster your vehicle is travelling the fas[...]

For rear wash cycle, rotate (and hold as desired) the rear wiper/washer control to either position. From either position, the control will automatically return to the INT 2 or OFF position. TILT STEERING WHEEL 1. Pull and hold the steering wheel release control toward you. 2. Move the steering up or down until you find the desired location. 3. Rele[...]

OVERHEAD CONSOLE The appearance of your vehicle’ s overhead console will vary according to your option package. Forward storage bin (if equipped) The storage compartment may be used to store a pair of sunglasses. Press the release area on the rear edge of the bin door to open the storage compartment. The door will open to full open position. Conv[...]

Power quarter rear windows (if equipped) Press the portion of the control to open the power rear quarter windows. Press the left portion of the control to close the power rear quarter windows. Do not leave children unattended in the vehicle and do not let children play with the power rear quarter windows. They may seriously injure themselves. When [...]

AUXILIARY POWER POINT (12VDC) Power outlets are designed for accessory plugs only . Do not insert any other object in the power outlet as this will damage the outlet and blow the fuse. Do not hang any type of accessory or accessory bracket from the plug. Improper use of the power outlet can cause damage not covered by your warranty . The auxiliary [...]

The rear auxiliary power point is located on the right rear quarter panel. The power point is accessible from the liftgate or the third row seat. Equipped with rear climate control Not equipped with rear climate control Cigar/Cigarette lighter (if equipped) Do not plug optional electrical accessories into the cigarette lighter socket. Do not hold t[...]

Cupholder/Ashtray (if equipped) The cupholder/ashtray is located on the instrument panel. T o open cupholder/ashtray , push in on the door and release. The door will spring out 1/4+ inches. Then pull cupholder/ashtray assembly out the remaining distance to utilize. T o close, push assembly in completely and release. POWER WINDOWS Do not leave child[...]

One touch down Allows the driver’ s window to open fully without holding the control down. Push the switch completely down to the second detent and release quickly . The window will open fully . Momentarily press the switch to any position to stop the window operation. Window lock The window lock feature allows only the driver to operate the powe[...]

Do not block the sensors on the front and back of the interior rear view mirror since this may impair proper mirror performance. Do not clean the housing or glass of any mirror with harsh abrasives, fuel or other petroleum-based cleaning products. EXTERIOR MIRRORS Power side view mirrors The ignition can be in any position to adjust the power side [...]

Heated outside mirrors (if equipped) Both mirrors are heated automatically to remove ice, mist and fog when the rear window defrost is activated. T ype A T ype B Do not remove ice from the mirrors with a scraper or attempt to readjust the mirror glass if it is frozen in place. These actions could cause damage to the glass and mirrors. Signal indica[...]

POWER ADJUSTABLE FOOT PEDALS (IF EQUIPPED) The accelerator and brake pedal should only be adjusted when the vehicle is stopped and the gearshift lever is in the P (Park) position. Press and hold the rocker control to adjust accelerator and brake pedal. • Press the top of the control to adjust the pedals toward you. • Press the bottom of the con[...]

3. Press the SET + control and release it. 4. T ake your foot off the accelerator pedal. 5. The indicator light on the instrument cluster will turn on. Note: • V ehicle speed may vary momentarily when driving up and down a steep hill. • If the vehicle speed increases above the set speed on a downhill, you may want to apply the brakes to reduce [...]

Increasing speed while using speed control There are two ways to set a higher speed: • Press and hold the SET + control until you get to the desired speed, then release the control. Y ou can also use the SET + control to operate the T ap-Up function. Press and release this control to increase the vehicle set speed in small amounts by 1 mph (1.6 k[...]

• Press the speed control OFF control. Note: When you turn off the speed control or the ignition, your speed control set speed memory is erased. STEERING WHEEL CONTROLS (IF EQUIPPED) These controls allow you to operate some radio and climate control features. Audio control features Press MEDIA to select: • AM, FM1, FM2 • CD (if equipped) • [...]

In any mode: • Press VOL + or − to adjust volume. Climate control features (if equipped) Press TEMP + or - to adjust temperature. Press F AN + or - to adjust fan speed. 2007 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus) Driver Controls 109[...]

Navigation control features (if equipped) Press and hold VOICE briefly until the voice icon appears on the Navigation display to use the Navigation voice command. Press the control again to hear previous command repeated from the navigation system. MOON ROOF (IF EQUIPPED) The moon roof control is located on the overhead console. Do not let children[...]

The moon roof has a built-in sliding shade that can be manually opened or closed when the glass panel is shut. T o close the shade, pull it toward the front of the vehicle. HOMELINK 姞 WIRELESS CONTROL SYSTEM (IF EQUIPPED) The HomeLink 威 W ireless Control System, located on the driver’ s visor , provides a convenient way to replace up to three[...]

1. Press and hold the two outside buttons releasing only when the indicator light begins to flash after 20 seconds. Do not repeat Step 1 to program additional hand-held transmitters to the remaining two HomeLink 威 buttons. This will erase previously programmed hand-held transmitter signals into HomeLink 威 . 2. Position the end of your hand-held[...]

Note: There are 30 seconds in which to initiate Step 7. 7. Return to the vehicle and firmly press, hold for two seconds and release the programmed HomeLink 威 button. Repeat the press/hold/release sequence again and, depending on the brand of the garage door opener (or other rolling code equipped device), repeat this sequence a third time to compl[...]

Operating the HomeLink 姞 Wireless Control System T o operate, simply press and release the appropriate HomeLink 威 button. Activation will now occur for the trained product (garage door , gate operator , security system, entry door lock, or home or office lighting etc.). For convenience, the hand-held transmitter of the device may also be used a[...]

STANDARD MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the ON position, the message center , located on your instrument cluster , displays important vehicle information through a constant monitor of vehicle systems. Y ou may select display features on the message center for a display of status preceded by a brief indicator chime. The system wi[...]

Distance to empty (DTE) Selecting this function from the INFO MENU estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will display LOW FUEL LEVEL and sound a ton[...]

Outside air temperature (OA T) The outside air temperature is shown together with the compass heading in the bottom row of the message center display . Compass display (if equipped) The compass heading is displayed as one of N, NE, E, SE, S, SW , W and NW in the message center display . The compass reading may be affected when you drive near large [...]

3. Locate the reset button on top of the compass sensor mounted behind the mirror . 4. Press and hold the reset button on the compass module for approximately 4 seconds until the message center displays a selection to change the current zone setting: ZONE <XX> RESET = CHANGE 5. Press and release the RESET stem to scroll through until the corr[...]

5. The compass is now calibrated. Setup menu This menu allows the user , via the RESET stem located in the instrument cluster , to interface and control the information displayed in the message center for following selectable features: • System Check • Oil life • Units (English/Metric) • Autolamp • Autolock • Language (English/French/Sp[...]

System check Selecting this function from the SETUP MENU causes the message center to cycle through each of the systems being monitored. For each of the monitored systems, the message center will indicate either an OK message or a warning message for 2 seconds. Pressing the RESET stem cycles the message center through each of the systems being moni[...]

Units (English/Metric) 1. Select this function from the SETUP MENU for the current units to be displayed. 2. Press and hold the RESET stem for 2 seconds to change from English to Metric. 3. Press the RESET stem for the next SETUP MENU item or wait for more than 4 seconds to return to the INFO MENU (“HOLD RESET FOR SETUP MENU” will appear). Auto[...]

Language Note: When entering the SETUP MENU and a non-English language has been selected, “HOLD RESET FOR ENGLISH” will be displayed to change back to English. 1. Select this function from the SETUP MENU for the current language to be displayed. 2. Press and hold the RESET stem for 2 seconds to select a new language. Selectable languages are En[...]

W arning display Status Driver door ajar W arning can be reset. W ill return if reset and warning is cleared and set again within the same ignition cycle. W ill return on ignition cycle. Passenger door ajar Rear left door ajar Rear right door ajar Door ajar Liftgate/glass ajar Check charging system T ire pressure sensor fault (if equipped) Low tire[...]

turn off as many of the electrical loads as soon as possible. If the warning stays on or comes on when the engine is operating at normal speeds, have the electrical system checked as soon as possible. P ARK BRAKE ENGAGED. Displayed when the manual park brake is set, the engine is running and the vehicle is driven more than 3 mph (5 km/h). If the wa[...]

OPTIONAL MESSAGE CENTER (IF EQUIPPED) W ith the ignition in the ON position, the message center , located on your instrument cluster , displays important vehicle information through a constant monitor of vehicle systems. Y ou may select display features on the message center for a display of status preceded by a brief indicator chime. The system wi[...]

Outside air temperature (if equipped) Press and hold the INFO button for 2 seconds to display the outside temperature. T o switch from a blank display to the temperature display , hold the INFO button for 2 seconds until the temperature is seen in the display . T o switch the temperature display to compass display , hold the INFO button again for 2[...]

5. Press and release the RESET until the message center displays a selection to change the current zone setting. 6. Press and release the RESET control until the message center display changes to show the current zone setting (XX). 7. Press and release the RESET control repeatedly until the correct zone setting for your geographic location is displ[...]

Distance to empty (DTE) Selecting this function from the INFO menu estimates approximately how far you can drive with the fuel remaining in your tank under normal driving conditions. Remember to turn the ignition OFF when refueling to allow this feature to correctly detect the added fuel. The DTE function will display XXX MILES TO E FUEL LEVEL LOW [...]

Instantaneous fuel economy Press INFO until the menu displays “MPG”. This will display your fuel economy as a Bar Graph ranging from poor economy to excellent economy . Y our vehicle must be moving to calculate instantaneous fuel economy . When your vehicle is not moving, this function shows one or no bars illuminated. Instantaneous fuel econom[...]

Reset to English (if in another language) When entering the SETUP MENU and a non-English language has been selected, “HOLD RESET FOR ENGLISH” will be displayed to change back to English. Press and hold the RESET control to set the language choice. Easy entry/exit (if equipped) This feature automatically moves the drivers seat backwards for easy[...]

Autolock This feature automatically locks all vehicle doors when the vehicle is shifted into any gear , putting the vehicle in motion. 1. T o disable/enable the autolock feature, select this function from the SETUP control for the current display mode. 2. Press the RESET control to turn the autolock ON or OFF . Power Liftgate (if equipped) This fea[...]

3. Press and hold the RESET control for 2 seconds to set the language choice. Units (English/Metric) 1. Select this function from the SETUP menu for the current units to be displayed. 2. Press the RESET control to change from English to Metric. System check Selecting this function from the SETUP menu causes the message center to cycle through each [...]

System warnings System warnings alert you to possible problems or malfunctions in your vehicle’ s operating systems. In the event of a multiple warning situation, the message center will cycle the display to show all warnings by displaying each one for 4 seconds. The message center will display the last selected feature if there are no more warni[...]

W arning display Status Brake fluid level low W arning can be reset. Will NOT return if reset and warning is cleared and set again within the same ignition cycle. W ill return on ignition cycle. Check park brake W asher fluid level low Oil change required XXX% Oil life change soon Check air suspension (if equipped) Check brake system W arning can b[...]

W arning display Status For 4x4 low stop vehicle (if equipped) T emporary alert For 4x4 apply brake (if equipped) For 4x4 shift to N (if equipped) T o exit 4x4 low stop vehicle (if equipped) T o exit 4x4 apply brake (if equipped) T o exit 4x4 shift to N (if equipped) DRIVER DOOR AJAR. Displayed when the driver door is not completely closed. P ASSEN[...]

Wheels and Loading chapter . If the warning stays on or continues to come on, have the system inspected by your authorized dealer . 4X4 SHIFT IN PROGRESS. Displayed on 4x4 vehicles only when 4x4 Low , 4x4 High or 4x4 Auto Range is selected. For further information, refer to AdvanceT rac 威 with RSC stability enhancement system in the Driving chapt[...]

An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule. USE ONL Y RECOMMENDED ENGINE OILS. T o reset the oil monitoring system to 100% after each oil change [approximately 5,000 miles (8,000 km) or 180 days] perform the following: 1. Press and release the SETUP control to display “[...]

POSITIVE RETENTION FLOOR MA T (IF EQUIPPED) Do not install additional floor mats on top of the factory installed floor mats as they may interfere with the accelerator or the brake pedals. Position the floor mat so that the eyelet is over the pointed end of the retention post and rotate forward to lock in. Make sure that the mat does not interfere w[...]

Keep keys out of reach of children. Do not allow children to play near an open or moving power liftgate. Do not open the liftgate in a garage or other enclosed area with a low ceiling. If the liftgate is raised the liftgate could be damaged against a low ceiling. T o open the liftgate from the Instrument panel: Press the button once to open the lif[...]

T o close the liftgate with the rear cargo area control button: Press and release the control on the left rear quarter panel to close the liftgate. The chime will beep once if conditions are not correct to start an operation (i.e., the vehicle is out of park). In a normal close, the chime will begin just before the gate starts to move and continue [...]

• disconnected battery • the liftgate is manually closed and left ajar (unlatched) T o reset the power liftgate: 1. Manually close and fully latch the liftgate. 2. Power open the liftgate by using the keyfob or instrument panel button. Note: If the power liftgate system is turned <OFF> in the message center , the system cannot be activate[...]

MANUAL LIFTGATE (IF EQUIPPED) • T o open the liftgate, position your hand on top of the liftgate handle and pull to open the liftgate. • Do not open the liftgate or liftgate glass in a garage or other enclosed area with a low ceiling. If the liftgate glass is raised and the liftgate is also opened, both liftgate and glass could be damaged again[...]

Cargo shelf/divider (if equipped) The cargo shelf/divider is located behind the rear seat of your vehicle. The shelf has two positions: Flat shelf which pivots up and snaps into place OR a divider which pivots up and snaps vertically into place. Do not put more than 30 lbs. (14 kg) on the shelf. T o move the shelf to the shelf position, pull up and[...]

LUGGAGE RACK Y our vehicle is equipped with a roof rack for transporting items on the exterior of the vehicle. The maximum recommended load to be carried on the roof rack is 200 lbs (90 kg), evenly distributed. The cross-bars can be adjusted by using the thumbwheels at each end. Use the tie-down loops on the thumbwheels to secure load. T o adjust t[...]

KEYS One key operates all the locks and starts the vehicle. Always carry a spare key with you in case of an emergency . Y our keys are programmed to your vehicle; using a non-programmed key will not permit your vehicle to start. If you lose your authorized dealer supplied keys, replacement keys are available through your authorized dealer . Refer t[...]

The autolock feature repeats when: • any door is opened then closed while the ignition is in the 3 (ON) position and the vehicle speed is 9 mph (15 km/h) or lower , and • the vehicle attains a speed greater than 12 mph (20 km/h). Deactivating/activating autolock Y our vehicle comes with the autolock feature enabled. There are four methods to en[...]

3. Enter 5–digit entry code 4. Press and hold the 3 • 4. While holding the 3 • 4 press the 7 • 8. 5. Release the 7 • 8. 6. Release the 3 • 4. The user should receive a horn chirp to indicate the system has been disabled or a chirp followed by a honk to indicate the system has been enabled. Message center procedure For information on act[...]

The remote entry lock/unlock feature operates in any ignition position. The liftgate glass features operate as long as vehicle speed is less than 5 mph (8 km/h). The panic feature operates with the key in the 1 (OFF/LOCK) position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL remote entry transmitters are bro[...]

• 4–button remote • 5–button remote If any of the doors or liftgate are ajar , the horn will make two quick chirps, reminding you to properly close all doors. Opening the liftgate window Press the control to unlatch the liftgate window . • 4–button remote 2007 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus) Locks and Security 14[...]

• 5–button remote Opening the power liftgate (if equipped) Press the control twice to fully unlatch and open the liftgate. Make sure all persons are clear of the liftgate area before using power liftgate control. In order to fully lower and latch the liftgate, press the control twice. If the liftgate stops mid travel, it may have detected an ob[...]

• 4–button remote • 5–button remote T o deactivate the alarm, press the control again or turn the ignition to the 2 (ACCESSORY) or 3 (ON) position. Memory feature The remote entry system can also control the memory feature. Press the control once to unlock the driver’ s door . Pressing the control will automatically move the seat, rearvie[...]

• 5–button remote Activating the memory feature T o activate this feature: 1. Position the seat, rearview mirror , and adjustable pedals to the positions you desire. 2. Press the SET control on the driver’ s seat. 3. W ithin 5 five seconds, press one control on the remote transmitter and then press the 1 or 2 memory seat control to which you [...]

T o replace the battery: 1. T wist a thin coin between the two halves of the remote entry transmitter near the key ring. DO NOT T AKE THE RUBBER COVER AND CIRCUIT BOARD OFF THE FRONT HOUSING OF THE REMOTE ENTRY TRANSMITTER. 2. Do not wipe off any grease on the battery terminals on the back surface of the circuit board. 3. Remove the old battery . N[...]

Programming remote transmitters It is necessary to have all (maximum of six — original and/or new) of your remote transmitters available prior to beginning this procedure. If all remote entry transmitters are not present during the programming procedure, the transmitters that are not present during programming will no longer operate the vehicle. [...]

Perimeter lamps illuminated entry The following items will illuminate when the (unlock) control on the remote entry transmitter is pressed: • Head lamps • Park lamps • T ail lamps The lamps will automatically turn off: • if the ignition switch is turned to the 3 (RUN) position, or • the (lock) control is pressed, or • after 25 seconds o[...]

been deactivated. The horn will chirp once and honk once (one short and one long) to indicate the perimeter lighting feature has been activated. 8. T urn the ignition to the 1 (LOCK) position to exit the procedure. Note: The horn will chirp once to confirm the procedure is complete. KEYLESS ENTRY SYSTEM (IF EQUIPPED) Y ou can use the keyless entry [...]

3. Press and hold the 1 • 2 for two seconds. This must be done within five seconds of completing Step 2. Y our personal code is now erased and only the factory set 5–digit code will work. Anti-scan feature If the wrong code has been entered 7 times (35 consecutive button presses), the keypad will go into an anti-scan mode. This mode disables th[...]

• When the ignition is in the 3 (ON) position, the indicator will glow for 3 seconds to indicate normal system functionality . If a problem occurs with the SecuriLock 娂 system, the indicator will flash rapidly or glow steadily when the ignition is in the 3 (ON) position. If this occurs, the vehicle should be taken to an authorized dealer for se[...]

Check to make sure the coded key is an approved Ford coded key . If your keys are lost or stolen you will need to do the following: • Use your spare key to start the vehicle, or • Have your vehicle towed to a authorized dealer or a locksmith. The key codes will need to be erased from your vehicle and new key codes will need to be re-coded. Repl[...]

4. T urn the ignition from the 3 (ON) back to 1 (OFF/LOCK) position in order to remove the second coded key from the ignition. 5. W ithin 10 seconds of removing the second coded key , insert the new unprogrammed key (new key/valet key) into the ignition and turn the ignition from the 1 (OFF/LOCK) to the 3 (ON) position [maintain ignition in 3 (ON) [...]

SEA TING Front row adjustable head restraints Y our vehicle’ s seats are equipped with two-way adjustable head restraints. The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close[...]

Lift handle to move seat forward or backward. Manual seat recliner (if equipped) Always drive and ride with your seatback upright and the lap belt snug and low across the hips. Reclining the seatback can cause an occupant to slide under the seat’ s safety belt, resulting in severe personal injuries in the event of a collision. Pull the seatback h[...]

Using the armrest (if equipped) Push the release control to move the armrest up or down. Using the manual lumbar support (if equipped) The lumbar support control is located on the outboard side of the seat. T urn the lumbar support control clockwise for more support. T urn the lumbar support counter -clockwise for less support. 2007 Expedition (exd[...]

Using the power lumbar support (if equipped) The power lumbar control is located on the outboard side of the seat. Press the forward side of the control for additional support. Press the rear side of the control to reduce support. Adjusting the front power seat Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile ca[...]

Move the switch in the direction of the arrows to raise or lower the rear portion of the seat cushion. Press the switch in the direction of the arrows to move the seat forward, backward, up or down. Press the control to recline the seatback forward or rearward. Note: On vehicles with memory seats, to prevent damage to the seat, the power seats are [...]

Memory seats/power mirrors/adjustable pedals (if equipped) This system allows automatic positioning of the driver seat, power mirrors, and adjustable pedals to two programmable positions. The memory seat control is located on the outboard side of the seat cushion. • T o program position 1, move the driver seat, mirrors and pedals (if equipped) to[...]

The controls for the climate controlled seats are located on the dual electronic automatic temperature control (DEA TC) system. Refer to Climate controls for more information. If the vehicle falls below 350 RPMs while the cooled seats are on, the feature will turn itself off and will need to be reactivated. Climate controlled seats air filter repla[...]

• Remove filter . T o install a filter: • First, position the filter in it’ s housing making sure that the far forward end is all the way up in the housing. Then push in on the center of the outside edge of the filter and rotate up into the housing until it clips into position. REAR SEATS Folding down the 2nd row 40% seat system Use caution w[...]

1. Lower the head restraints by pulling on the strap. 2. Locate handle on the side of the seat cushion by the door . 3. Pull up on the handle and push the seatback forward toward the front of the vehicle. T o return the seat to the upright position: 1. Lift the seatback toward the rear of the vehicle. 2. Rotate the seatback until you hear a click, [...]

3. Lift up on the head restraint until it locks into its original position. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After returning the seatback to its original position, pull on the seatback to ensure that it has fully latched. An unlatched seat may become dan[...]

2. Pull the cargo mode lever up to release the seat into a kneel down load floor position. A moderate force may be required to move the seat forward and down. Returning to the upright position from full lowered load floor position The seatback cannot be returned to the upright position until the seat is returned from the kneel down position. T o re[...]

2. Pull the handle up again until the seat releases from the floor . 3. Push the seat upward and fold it away from the third row . Always latch the vehicle seat to the floor , whether the seat is occupied or empty . If not latched, the seat may cause injury during a sudden stop. T o return the seat to a seating position: 1. Push the seat down and l[...]

Exiting the 3rd row 1. Pull the strap located at the bottom outboard of the seat back to release the seat from the floor , and rotate the seat up towards the front seat. 2. Follow the directions above to return the seat from the E-Z entry and to the upright position. Reclining the 2nd row outboard 40% seatback Locate the release handle on the outbo[...]

T o prevent possible damage to the seat or safety belts, ensure that the safety belts are not buckled when moving the seat to the load floor position. 2. W ith the latch released the seatback can be lowered into the load floor position. 3. T o return the seat to the upright position, lift the seatback until the latch is fully engaged. Before return[...]

Adjusting the 2nd row center 20% seat (if equipped) Lift the handle to move the seat forward or backward. Note: This seat can be moved forward to keep a child in a child restraint close to the front seat occupants. The seat should be moved to the full rearward position when it is occupied by older children or adults. 3rd row seats Ensure that no ob[...]

Pull up on the handle located behind the seatback while pushing the seatback forward and down into the seat cushion. T o return the seatback to its original position lift the seatback until it latches into place. Before returning the seatback to its original position, make sure that cargo or any objects are not trapped behind the seatback. After re[...]

Push the bottom portion of the control button to lower the desired seatback. Push the top of the control button to return the seatback to its original position. The power fold down seats will operate for 10 minutes after the ignition switch is in Off. The transmission must be in P (park), and the liftgate, or liftgate glass must be open. Similar to[...]

SAFETY RESTRAINTS Personal Safety System 姟 The Personal Safety System 娂 provides an improved overall level of frontal crash protection to front seat occupants and is designed to help further reduce the risk of airbag-related injuries. The system is able to analyze different occupant conditions and crash severity before activating the appropriat[...]

Driver and passenger dual-stage airbag supplemental restraints The dual-stage airbags offer the capability to tailor the level of airbag inflation energy . A lower , less forceful energy level is provided for more common, moderate-severity impacts. A higher energy level is used for the most severe impacts. Refer to Airbag supplemental restraints se[...]

Determining if the Personal Safety System 姟 is operational The Personal Safety System 娂 uses a warning light in the instrument cluster or a back-up tone to indicate the condition of the system. Refer to the W arning lights and chimes section in the Instrument Cluster chapter . Routine maintenance of the Personal Safety System 娂 is not require[...]

It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in any area of your vehicle that is not equipped with seats and safety belts. Be sure everyone in your vehicle is in a seat and using a safety [...]

Combination lap and shoulder belts 1. Insert the belt tongue into the proper buckle (the buckle closest to the direction the tongue is coming from) until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. • Front and rear seats 2. T o unfasten, push the release button and remove the tongue from the buckle.[...]

Front center lap belt T o fasten the front center lap belt, insert the tongue into the center buckle until you hear a snap and feel it latch. Make sure the tongue is securely fastened in the buckle. Pull on the webbing to tighten the belt. All combination lap/shoulder belts, other than the driver’ s belt, have two modes: V ehicle sensitive mode T[...]

How to use the automatic locking mode 1. Buckle the combination lap and shoulder belt. 2. Grasp the shoulder portion and pull downward until the entire belt is pulled out. 3. Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the auto[...]

BEL T AND RETRACTOR ASSEMBL Y MUST BE REPLACED if the safety belt assembly “automatic locking retractor” feature or any other safety belt function is not operating properly . In addition, all safety belts should be checked for proper function. Failure to replace the belt and retractor assembly could increase the risk of injury in collisions. Sa[...]

Position the safety belt height adjusters so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the seat belt and increase the risk of injury in a collision. Second row comfort guide The second row outboard lap/shoulder belt is equipped with a belt comfort guide. Thi[...]

Position the safety belt comfort guide so that the belt rests across the middle of your shoulder . Failure to adjust the safety belt properly could reduce the effectiveness of the safety belt and increase the risk of injury in a collision. Safety belt extension assembly If the safety belt is too short when fully extended, there is a 8 inch (20 cm) [...]

Conditions of operation If... Then... The driver safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates 1-2 minutes and the warning chime sounds 4-8 seconds. The driver safety belt is buckled while the indicator light is illuminated and the warning chime is sounding... The saf[...]

If... Then... The driver’ s safety belt is not buckled approximately 5 seconds after the safety belt warning light has turned off... The Belt-Minder 威 feature is activated - the safety belt warning light illuminates and the warning chime sounds for 6 seconds every 30 seconds, repeating for approximately 5 minutes or until safety belt is buckled[...]

Reasons given... Consider ... “Belts are uncomfortable” W e design our safety belts to enhance comfort. If you are uncomfortable - try different positions for the safety belt upper anchorage and seatback which should be as upright as possible; this can improve comfort. “I was in a hurry” Prime time for an accident. Belt-Minder 威 reminds u[...]

Do not sit on top of a buckled safety belt or insert a latchplate into the buckle to avoid the Belt-Minder 威 chime. T o do so may adversely affect the performance of the vehicle’ s air bag system One time disable Any time the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt-Minder 威 will be disabled for that ignitio[...]

4. W ithin approximately 7 seconds of the light turning off, buckle then unbuckle the safety belt. • This will disable the Belt-Minder 威 feature for that seating position if it is currently enabled. As confirmation, the safety belt warning light will flash 4 times per second for 3 seconds. • This will enable the Belt-Minder 威 feature for th[...]

All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag supplemental restraint system (SRS) is provided. Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. The National Highway T raffic Safety Administration (NHTSA)[...]

Additional equipment may affect the performance of the airbag sensors increasing the risk of injury . Children and airbags Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions ma[...]

The airbags inflate and deflate rapidly upon activation. After airbag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the airbag. Small amo[...]

The RCM (restraints control module) monitors its own internal circuits and the supplemental airbag electrical system wiring (including the impact sensors, the system wiring, the airbag system readiness light, the airbag back up power and the airbag ignitors). Determining if the system is operational The SRS uses a readiness light in the instrument [...]

Do not attempt to service, repair , or modify the airbag SRS, its fuses or the seat cover on a seat containing an airbag. See your authorized dealer . All occupants of the vehicle should always wear their safety belts even when an airbag SRS is provided. How does the side airbag system work? The design and development of the side airbag system incl[...]

The fact that the airbags did not inflate in a collision does not mean that something is wrong with the system. Rather , it means the forces were not of the type sufficient to cause activation. Side airbags are designed to inflate in side-impact collisions, not roll-over , rear -impact, frontal or near -frontal collisions, unless the collision caus[...]

Do not attempt to service, repair , or modify the Safety Canopy 娂 system, its fuses, the A, B, C or D pillar trim, or the headliner on a vehicle containing a Safety Canopy 娂 . See your authorized dealer . All occupants of the vehicle including the driver should always wear their safety belts even when an airbag SRS and Safety Canopy 娂 system [...]

• T wo crash sensors mounted in the front doors (one on each side of the vehicle). • T wo crash sensors located at the C pillar behind the rear doors (one on each side of the vehicle). • Rollover sensor in the restraints control module (RCM). The Safety Canopy 娂 system, in combination with safety belts, can help reduce the risk of severe in[...]

If the Safety Canopy 娂 system has deployed, the Safety Canopy 娂 will not function again unless replaced. The Safety Canopy 娂 system (including the A, B, C, and D pillar trim) must be inspected and serviced by an authorized dealer . If the Safety Canopy 娂 is not replaced, the unrepaired area will increase the risk of injury in a collision. D[...]

Important child restraint precautions Y ou are required by law to use safety restraints for children in the U.S. and Canada. If small children (generally children who are four years old or younger and who weigh 40 lb. [18 kg] or less) ride in your vehicle, you must put them in safety seats made especially for children. Many states require that chil[...]

T o improve the fit of both the lap and shoulder belt on children who have outgrown child safety seats, Ford Motor Company recommends use of a belt-positioning booster . Booster seats position a child so that safety belts fit better . They lift the child up so that the lap belt rests low across the hips and the knees bend comfortably . Booster seat[...]

T ypes of booster seats There are two types of belt-positioning booster seats: • Those that are backless. If your backless booster seat has a removable shield, remove the shield and use the lap/shoulder belt. If a seating position has a low seat back and no head restraint, a backless booster seat may place your child’ s head (top of ear level) [...]

Children and booster seats vary widely in size and shape. Choose a booster that keeps the lap belt low and snug across the hips, never up across the stomach, and lets you adjust the shoulder belt to cross the chest and rest snugly near the center of the shoulder . The drawings below compare the ideal fit (center) to a shoulder belt uncomfortably cl[...]

Never use pillows, books, or towels to boost a child. They can slide around and increase the likelihood of injury or death in a collision. SAFETY SEATS FOR CHILDREN Child and infant or child safety seats Use a safety seat that is recommended for the size and weight of the child. Carefully follow all of the manufacturer’ s instructions with the sa[...]

for children up to 60 pounds (27 kg) in a child restraint, and to provide upper torso restraint for children up to 80 pounds (36 kg) using an upper torso harness and a belt-positioning booster . Ford recommends the use of a child safety seat having a top tether strap. Install the child safety seat in a seating position with LA TCH and tether anchor[...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is pulled out and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buc[...]

Installing child safety seats in the center front seating position (if equipped) Always transport children 12 years old and under in the rear seats and always properly use appropriate child restraints. It is safer to install child safety seats in seating positions that have child seat anchors. The front seat has no tether anchor nor does it have LA[...]

The tether strap anchors in your vehicle are in the following positions (shown from top view): • Second row bench seat • Second row bucket seats Attach the tether strap only to the appropriate tether anchor as shown. The tether strap may not work properly if attached somewhere other than the correct tether anchor . Second row seating positions [...]

• center seating position (if equipped) 3. Route the child safety seat tether strap under the head restraint (outboard seats) and over the back of the seat. 4. Grasp the tether strap and position it to the seat frame. 5. Rotate the tether strap, and clip the tether strap to the anchor on the seat frame. 2007 Expedition (exd) Owners Guide (post-20[...]

6. Rotate the tether strap clip. 7. T ighten the child safety seat tether strap according to the manufacturer’ s instructions. Third row seating position 1. Position the child safety seat on the center of the seat cushion. 2. Route the child safety seat tether strap over the back of the seat. 3. Locate the anchor webbing loop for the seating posi[...]

4. Clip the tether strap through the anchor loop as shown. If the tether strap is clipped incorrectly , the child safety seat may not be retained properly in the event of a collision. 5. Install the child safety seat tightly using the LA TCH anchors or safety belts. Follow the instructions in this chapter . 6. T ighten the child safety seat tether [...]

Y our vehicle has LA TCH anchors for child seat installation at the seating positions marked with the child seat symbol: Never attach two LA TCH child safety seats to the same anchor . In a crash, one anchor may not be strong enough to hold two child safety seat attachments and may break, causing serious injury or death. The lower anchors for child[...]

Attach LA TCH lower attachments of the child seat only to the anchors shown. If you install a child seat with rigid LA TCH attachments, do not tighten the tether strap enough to lift the child seat off the vehicle seat cushion when the child is seated in it. Keep the tether strap just snug without lifting the front of the child seat. Keeping the ch[...]

NOTICE TO UTILITY VEHICLE AND TRUCK OWNERS Utility vehicles and trucks handle differently than passenger cars in the various driving conditions that are encountered on streets, highways and off-road. Utility vehicles and trucks are not designed for cornering at speeds as high as passenger cars any more than low-slung sports cars are designed to per[...]

Power is supplied to all four wheels through a transfer case or power transfer unit. 4WD vehicles allow you to select different drive modes as necessary . Information on transfer case operation and shifting procedures can be found in the Driving chapter . Information on transfer case maintenance can be found in the Maintenance and Specifications ch[...]

• Narrower — to provide greater maneuverability in tight spaces, particularly in off-road use. As a result of the above dimensional differences, SUV’ s and trucks often will have a higher center of gravity and a greater difference in center of gravity between the loaded and unloaded condition. These differences that make your vehicle so versa[...]

government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the actual conditions of their use, however , and may depart significantly from the norm due to variations in driving habits, service practices, and di[...]

• T ire Identification Number (TIN): A number on the sidewall of each tire providing information about the tire brand and manufacturing plant, tire size and date of manufacture. Also referred to as DOT code. • Inflation pressure: A measure of the amount of air in a tire. • Standard load: A class of P-metric or Metric tires designed to carry a[...]

At least once a month and before long trips, inspect each tire and check the tire pressure with a tire gauge (including spare, if equipped). Inflate all tires to the inflation pressure recommended by Ford Motor Company . Use a tire gauge to check the tire inflation pressure, including the spare (if equipped), at least monthly and before long trips.[...]

T o check the pressure in your tire(s): 1. Make sure the tires are cool, meaning they are not hot from driving even a mile. If you are checking tire pressure when the tire is hot, (i.e. driven more than 1 mile [1.6 km]), never “bleed” or reduce air pressure. The tires are hot from driving and it is normal for pressures to increase above recomme[...]

cracking, cuts, bruises and other signs of damage or excessive wear . If internal damage to the tire is suspected, have the tire demounted and inspected in case it needs to be repaired or replaced. For your safety , tires that are damaged or show signs of excessive wear should not be used because they are more likely to blow out or fail. Improper o[...]

U.S. DOT Tire Identification Number (TIN) Both U.S. and Canada Federal regulations require tire manufacturers to place standardized information on the sidewall of all tires. This information identifies and describes the fundamental characteristics of the tire and also provides a U.S. DOT T ire Identification Number for safety standard certification[...]

When mounting replacement tires and wheels, you should not exceed the maximum pressure indicated on the sidewall of the tire to set the beads without additional precautions listed below . If the beads do not seat at the maximum pressure indicated, re-lubricate and try again. When inflating the tire for mounting pressures up to 20 psi greater than t[...]

If your vehicle is stuck in snow , mud, sand, etc., do not rapidly spin the tires; spinning the tires can tear the tire and cause an explosion. A tire can explode in as little as three to five seconds. Do not spin the wheels at over 35 mph (56 km/h). The tires may fail and injure a passenger or bystander . Highway hazards No matter how carefully yo[...]

• Rear Wheel Drive (RWD) vehicles/Four Wheel Drive (4WD)/ All Wheel Drive (A WD) vehicles (front tires at top of diagram) Sometimes irregular tire wear can be corrected by rotating the tires. Note: If your tires show uneven wear ask an authorized dealer to check for and correct any wheel misalignment, tire imbalance or mechanical problem involved[...]

Information on “P” type tires P215/65R15 95H is an example of a tire size, load index and speed rating. The definitions of these items are listed below . (Note that the tire size, load index and speed rating for your vehicle may be different from this example.) 1. P: Indicates a tire, designated by the T ire and Rim Association (T&RA), that[...]

Note: Y ou may not find this information on all tires because it is not required by federal law . Letter rating Speed rating - mph (km/h) M 81 mph (130 km/h) N 87 mph (140 km/h) Q 99 mph (159 km/h) R 106 mph (171 km/h) S 112 mph (180 km/h) T 118 mph (190 km/h) U 124 mph (200 km/h) H 130 mph (210 km/h) V 149 mph (240 km/h) W 168 mph (270 km/h) Y 186[...]

12. T readwear , T raction and T emperature Grades • T readwear: The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1 ⁄ 2 ) times as well on the government course as a tire grad[...]

Additional information contained on the tire sidewall for “L T” type tires “L T” type tires have some additional information beyond those of “P” type tires; these differences are described below: 1. LT: Indicates a tire, designated by the T ire and Rim Association (T&RA), that is intended for service on light trucks. 2. Load Range/L[...]

Information on “T” type tires “T” type tires have some additional information beyond those of “P” type tires; these differences are described below: T145/80D16 is an example of a tire size. Note: The temporary tire size for your vehicle may be different from this example. 1. T: Indicates a type of tire, designated by the T ire and Rim A[...]

TIRE PRESSURE MONITORING SYSTEM (TPMS) Each tire, including the spare (if provided), should be checked monthly when cold and inflated to the inflation pressure recommended by the vehicle manufacturer on the vehicle placard or tire inflation pressure label. (If your vehicle has tires of a different size than the size indicated on the vehicle placard[...]

Changing tires with TPMS Each road tire is equipped with a tire pressure sensor fastened to the inside rim of the wheel. The pressure sensor is covered by the tire and is not visible unless the tire is removed. The pressure sensor is located opposite (180 degrees) from the valve stem. Care must be taken when changing the tire to avoid damaging the [...]

no longer capable of functioning as intended. Please refer to the following chart for information concerning your T ire Pressure Monitoring System: Low T ire Pressure W arning Light Possible cause Customer Action Required Solid W arning Light T ire(s) under -inflated 1. Check your tire pressure to ensure tires are properly inflated; refer to Inflat[...]

Low T ire Pressure W arning Light Possible cause Customer Action Required Flashing W arning Light Spare tire in use Y our temporary spare tire is in use. Repair the damaged road wheel and re-mount it on the vehicle to restore system functionality . For a description of how the system functions under these conditions, refer to When your temporary sp[...]

any tire is under -inflated, carefully drive the vehicle to the nearest location where air can be added to the tires. Inflate all the tires to the recommended inflation pressure. SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tires you currently have on your vehicle. The tires on your vehicle have all weather treads to prov[...]

your vehicle, familiarize yourself with the following terms for determining your vehicle’ s weight ratings, with or without a trailer , from the vehicle’ s T ire Label or Safety Compliance Certification Label: Base Curb W eight – is the weight of the vehicle including a full tank of fuel and all standard equipment. It does not include passeng[...]

Example only: Cargo W eight – includes all weight added to the Base Curb W eight, including cargo and optional equipment. When towing, trailer tongue load or king pin weight is also part of cargo weight. GA W (Gross Axle W eight) – is the total weight placed on each axle (front and rear) – including vehicle curb weight and all payload. 2007 E[...]

GA WR (Gross Axle W eight Rating) – is the maximum allowable weight that can be carried by a single axle (front or rear). These numbers are shown on the Safety Compliance Certification Label located on the B-Pillar or the edge of the driver’ s door . The total load on each axle must never exceed its GA WR. Note: For trailer towing information r[...]

GCW (Gross Combined W eight) – is the weight of the loaded vehicle (GVW) plus the weight of the fully loaded trailer . GCWR (Gross Combined W eight Rating) – is the maximum allowable weight of the vehicle and the loaded trailer – including all cargo and passengers – that the vehicle can handle without risking damage. (Important: The towing [...]

Exceeding any vehicle weight rating limitation could result in serious damage to the vehicle and/or personal injury . Steps for determining the correct load limit: 1. Locate the statement “The combined weight of occupants and cargo should never exceed XXX kg or XXX lbs.” on your vehicle’ s placard. 2. Determine the combined weight of the driv[...]

transport the cement to your home? If you and your friend each weigh 220 lb. (99 kg), the calculation would be: 1400 - (2 x 220) - (12 x 100) = 1400 - 440 - 1200 = - 240 lb. No, you do not have enough cargo capacity to carry that much weight. In metric units, the calculation would be: 635 kg - (2 x 99 kg) - (12 x 45 kg) = 635 - 198 - 540 = -103 kg.[...]

• Thoroughly prepare your vehicle for towing. Refer to Preparing to tow in this chapter . • Use extra caution when driving while trailer towing. Refer to Driving while you tow in this chapter . • Service your vehicle more frequently if you tow a trailer . Refer to the severe duty schedule in the scheduled maintenance guide. • Do not tow a t[...]

Engine Rear axle ratio Maximum GCWR - lb. (kg) T railer weight range (0 - maximum) lb. (kg) 4x2 5.4L with standard trailer tow package All 11800 (5351) 0–6000 (0–2721) 5.4L with optional trailer tow package All 15000 (6804) 0–9200 (0–4173) 4x4 5.4L with standard trailer tow package All 12100 (5489) 0–6000 (0–2721) 5.4L with optional tra[...]

Engine Rear axle ratio Maximum GCWR - lb. (kg) T railer weight range (0 - maximum) lb. (kg) Expedition EL (U.S. Only) Expedition Max (Canada Only) 4x2 5.4L with standard trailer tow package All 12200 (5534) 0–6000 (0–2721) 5.4L with optional trailer tow package All 15000 (6804) 0–9000 (0–4082) Expedition EL (U.S. Only) Expedition Max (Canad[...]

Integrated hitch rating The standard integrated hitch has two ratings depending on mode of operation: • W eight carrying - requires a draw bar and hitch ball. The draw bar supports all the vertical tongue load of the trailer . • W eight distributing - requires an aftermarket weight distributing system which includes draw bar , hitch ball, sprin[...]

2. T urn the air suspension (if equipped) control to OFF . 3. Measure the height of a reference point on the front and rear bumpers at the center of the vehicle. 4. Attach the trailer to the vehicle and adjust the hitch equalizers so that the front bumper height is within a 1 ⁄ 2 ” (13 mm) of the reference point. After proper adjustment, the re[...]

Driving while you tow When towing a trailer: • Keep your speed no faster than 70 mph (112 km/h) during the first 500 miles (800 km) of towing a trailer , and don’t make full throttle starts. • T urn off the speed control. The speed control may shut off automatically when you are towing on long, steep grades. • Consult your local motor vehic[...]

the lubricant specification. Remember that regardless of the rear axle lube used, do not tow a trailer for the first 500 miles (800 km) of a new vehicle, and that the first 500 miles (800 km) of towing be done at no faster than 70 mph (112 km/h) with no full throttle starts. • After you have traveled 50 miles (80 km), thoroughly check your hitch,[...]

If a distance of 50 miles (80 km) or a speed of 35 mph (56 km/h) must be exceeded, the drive shaft will have to be removed before the vehicle is towed. Ford recommends the driveshaft be removed/installed only by a qualified technician at an authorized dealer . See your authorized dealer for driveshaft removal/installation. Improper removal/installa[...]

STARTING Positions of the ignition 1. OFF/LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 2. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 3. ON, all electrical circuits operational. W arning lights illuminated. Key position when driving. 4.[...]

If you smell exhaust fumes inside your vehicle, have your dealer inspect your vehicle immediately . Do not drive if you smell exhaust fumes. Important safety precautions A computer system controls the engine’ s idle revolutions per minute (RPM). When the engine starts, the idle RPM runs higher than normal in order to warm the engine. If the engin[...]

4. Make sure the parking brake is set. 5. T urn the key to 3 (ON) without turning the key to 4 (ST ART). Some warning lights will briefly illuminate. See W arning lights and chimes in the Instrument Cluster chapter for more information regarding the warning lights. Starting the engine Note: Whenever you start your vehicle, release the key once the [...]

3. After idling for a few seconds, apply the brake, shift into gear and drive. Note: If the engine does not start within five seconds on the first try , turn the key to OFF , wait 10 seconds and try again. If the engine still fails to start, press the accelerator to the floor and try again; this will allow the engine to crank with the fuel shut off[...]

results, plug the heater in at least three hours before starting the vehicle (the heater can be plugged in the night before starting the vehicle). T o plug the heater in, remove the cap from the plug and insert the plug into a 110 volt grounded outlet. Be sure to re-attach the cap onto the plug when the heater is not in use. T o reduce the risk of [...]

mechanical noise may be heard during this test. This is normal. If a malfunction is found, the ABS warning light will come on. If the vehicle has continuous vibration or shudder in the steering wheel while braking, the vehicle should be inspected by an authorized dealer . The ABS operates by detecting the onset of wheel lockup during brake applicat[...]

Parking brake Apply the parking brake whenever the vehicle is parked. T o set the parking brake, press the parking brake pedal down until the pedal stops. The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is released. If the parking brake is fully released, [...]

Pull the release lever to release the brake. Driving with the parking brake on will cause the brakes to wear out quickly and reduce fuel economy . ADVANCET RAC 姞 WITH ROLL STABILITY CONTROL 姟 (RSC) STABILITY ENHANCEMENT SYSTEM (IF EQUIPPED) The AdvanceT rac 威 with RSC system provides stability enhancement features such as Roll Stability Contr[...]

If your vehicle should become stuck in deep snow or mud, try switching the AdvanceT rac 威 with RSC system off by pressing the AdvanceT rac 威 with RSC button momentarily . This will allow your tires to “dig” for traction. If the AdvanceT rac 威 with RSC system is activated excessively in a short period of time, the brake portion of the syst[...]

• Driving on slick surfaces. • Cornering while towing a heavily loaded trailer (refer to T railer towing in the T ires, Wheels and Loading chapter .) Roll Stability Control 娂 (RSC) The RSC system works in conjunction with the AdvanceT rac 威 system to help maintain roll stability of the vehicle during aggressive maneuvers by applying brake f[...]

icon, however , the AdvanceT rac 威 with RSC system will remain enabled until the vehicle speed drops below 25 mph. If the vehicle speed decreases below 25 mph (40 km/h), the system will become deactivated, but if the vehicle speed subsequently increases to above 25 mph (40 km/h), the system will again become active. In general, the system will be[...]

Aggressive driving in any road conditions can cause you to lose control of your vehicle increasing the risk of severe personal injury or property damage. The occurrence of a AdvanceT rac 威 with RSC event is an indication that at least some of the tires have exceeded their ability to grip the road; this may lead to an increased risk of loss of veh[...]

• High crosswinds • Wheels out of alignment • Loose or worn suspension components V ariable assist steering Y our vehicle is equipped with variable assist power steering. At low engine RPM, steering assist will adjust to reduce efforts and improve low speed maneuverability . At high engine RPM, the assist will adjust to improve steering feel [...]

LIMITED-SLIP AXLE (IF EQUIPPED) This axle provides added traction on slippery surfaces, particularly when one wheel is on a poor traction surface. Under normal conditions, the limited slip axle functions like a standard rear axle. Extended use of other than the manufacturer’ s specified size tires on a limited slip rear axle could result in a per[...]

If you cannot move the gearshift lever out of P (Park) with ignition in the ON position and the brake pedal depressed, or when the ignition is in the OFF position, it is possible that a fuse has blown or the vehicle’ s brakelamps are not operating properly . Refer to Fuses and relays in the Roadside Emergencies chapter . If the fuse is not blown,[...]

If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer . Brake-shift interlock – floor-shift transmission This vehicle is equipped with a brake-shift interlock feature that prevents the gearshift lever from being moved from P (Park) when the ignit[...]

Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. If the parking brake is fully released, but the brake warning lamp remains illuminated, the brakes may not be working properly . See your authorized dealer . Driving with [...]

T o put your vehicle in P (Park): • Come to a complete stop • Move the gearshift lever and securely latch it in P (Park) Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the ignition to the LOCK position and remove the key whenever you leave your vehicle. R (Reverse) W ith the gearshift lever in R (Re[...]

• Floor -shift transmission T ransmission operates in gears one through six except in 4L where transmission operates in gears two through six. • Provides engine braking. • Use when driving conditions cause excessive shifting from O/D to other gears. Examples: city traffic, hilly terrain, heavy loads, trailer towing and when engine braking is [...]

• Provides maximum engine braking. • Allows upshifts by moving gearshift lever . • W ill not downshift into 1 (First) at high speeds; allows for 1 (First) when vehicle reaches slower speeds. Forced downshifts • Allowed in D (Drive) only . • Depress the accelerator to the floor . • Allows transmission to select an appropriate gear . If y[...]

Certain add-on devices such as large trailer hitches, bike or surfboard racks and any device that may block the normal detection zone of the reverse sensing system may create false beeps. The system will assist the driver in detecting certain objects while the vehicle moves in reverse at speeds less than 6 mph (10 km/h). The system is not effective[...]

Audible W arnings Distance to Object W arning Speed below 2.5 mph (4 km/h) up to 1.4 feet (.4 meters) Solid 1.4 feet (.4 meters) to 3 feet (.9 meters) Fast beep 3 feet (.9 meters) to 4.5 feet (1.4 meters) Medium beep 4.5 feet (1.4 meters) to 6.3 feet (1.9 meters) Medium/slow beep 6.3 feet (1.9 meters) to 8.7 feet (2.6 meters) Slow beep 8.7 feet (2.[...]

damage drive components. 4H (4X4) and 4L (4X4 LOW) are only intended for consistently slippery or loose surfaces. Use of 4H (4X4) or 4L (4X4 LOW) on these surfaces may produce some noise (such as occasional clunks) but will not damage drive components. Y our 4x4 features the heavy-duty Control T rac system which includes a computer -operated transf[...]

• 4L (4X4 LOW) provides electronically locked four -wheel drive when extra power at reduced speeds is required. The RTT location in the message center will display “4X4 LOW” when this position is selected. This position is not recommended for use on dry pavement. Use this position for off-road low-speed operation or when extra power is requir[...]

Shifting to/from 4L 1. Bring the vehicle to a stop. 2. Place the gearshift in N (Neutral). 3. Move the control to the desired position. The message center will display “4X4 SHIFT IN PROGRESS” during the shift. The RTT location in the message center will then display the system mode selected. If any of the above shift conditions are not met, the[...]

steering and braking control of your vehicle, you must have all four wheels on the ground and they must be rolling, not sliding or spinning. Basic operating principles • Do not use 4H (4x4) or 4L (4x4 LOW) on dry , hard surfaced roads. This may damage the driveline and axles. • Drive slower in strong crosswinds which can affect the normal steer[...]

Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur . Do not rock the vehicle for more than a few minutes or damage to the transmission and tires may occur or the engine may overheat. Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn the igni[...]

• If the vehicle goes from one type of surface to another (i.e., from concrete to gravel) there will be a change in the way the vehicle responds to a maneuver (steering, acceleration or braking). Again, avoid these abrupt inputs. Control Trac four–wheel drive system (if equipped) When a four–wheel drive mode is selected, the Control T rac sys[...]

Mud and water If you must drive through high water , drive slowly . T raction or brake capability may be limited. When driving through water , determine the depth; avoid water higher than the bottom of the hubs (if possible) and proceed slowly . If the ignition system gets wet, the vehicle may stall. Once through water , always try the brakes. W et[...]

possibly rolling over . Whenever driving on a hill, determine beforehand the route you will use. Do not drive over the crest of a hill without seeing what conditions are on the other side. Do not drive in reverse over a hill without the aid of an observer . When climbing a steep slope or hill, start in a lower gear rather than downshifting to a low[...]

A void sudden applications of power and quick changes of direction on snow and ice. Apply the accelerator slowly and steadily when starting from a full stop. A void sudden braking as well. Although a four–wheel drive vehicle may accelerate better than a two-wheel drive vehicle in snow and ice, it won’t stop any faster , because as in other vehi[...]

DRIVING THROUGH WATER If driving through deep or standing water is unavoidable, proceed very slowly especially when the depth is not known. Never drive through water that is higher than the bottom of the wheel rims (for cars) or the bottom of the hubs (for trucks). When driving through water , traction or brake capability may be limited. Also, wate[...]

ROADSIDE ASSISTANCE Getting roadside assistance T o fully assist you should you have a vehicle concern, Ford Motor Company offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the period of five years or 60,000 miles[...]

• towing of your disabled vehicle • emergency travel expense reimbursement • travel planning benefits Using roadside assistance Complete the roadside assistance identification card and place it in your wallet for quick reference. In the United States, this card is found in the Owner Guide portfolio in the glove compartment. In Canada, the car[...]

FUEL PUMP SHUT-OFF SWITCH FUEL RESET The fuel pump shut-off switch is a device intended to stop the electric fuel pump when your vehicle has been involved in a substantial jolt. After a collision, if the engine cranks but does not start, the fuel pump shut-off switch may have been activated. The fuel pump shut-off switch is located behind an access[...]

FUSES AND RELAYS Fuses If electrical components in the vehicle are not working, a fuse may have blown. Blown fuses are identified by a broken wire within the fuse. Check the appropriate fuses before replacing any electrical components. Note: Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage r[...]

Passenger compartment fuse panel The fuse panel is located under the right-hand side of the instrument panel. T o remove the trim panel for access to the fuse box, pull the panel toward you and swing it out away from the side and remove it. T o reinstall it, line up the tabs with the grooves on the panel, then push it shut. T o remove the fuse box [...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 30A Smart window #1 2 15A Driver side memory module 3 15A FES, Audio rear seat controls, SDARS 4 30A Smart window #2 5 10A Keypad illumination, 3rd row seat enable, Brake Shift Interlock (BSI), SPDJB 6 20A T urn signals 7 10A Low beam [...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 25 10A Demand lamps, Glovebox, Visor 26 10A Instrument panel cluster 27 20A Ignition switch 28 5A Radio 29 5A Instrument panel cluster 30 5A Not used (Spare) 31 10A Compass, Automatic dimming rear view mirror 32 10A Restraints control module 33 — Not used 34 5A Not u[...]

Always disconnect the battery before servicing high current fuses. T o reduce risk of electrical shock, always replace the cover to the Power Distribution Box before reconnecting the battery or refilling fluid reservoirs. If the battery has been disconnected and reconnected, refer to the Battery section of the Maintenance and Specifications chapter[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 11 30A** Auxiliary blower 12 25A* T railer tow connector (park lamps) 13 30A * T railer tow connector (battery charge) 14 — Not used 15 — Not used 16 — A/C clutch relay 17 — Not used 18 — Fuel pump relay 19 — Back-up relay 20 — T railer tow connector relay (left tu[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 36 10A* Powertrain Control Module (PCM) – Keep alive power , Canister vent 37 15A* T ransmission B+ 38 30A** Third row seats (passenger side) 39 50A** Air suspension pump 40 30A** Starter motor 41 20A** IP/Console power point 42 — Not used 43 20A** 4x4 module motor 44 — No[...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 63 15A* T railer tow connector (back-up lamp) 64 — Not used 65 10A* Air suspension logic 66 — Not used 67 10A* Blower coil 68 — Not used 69 30A* Run/Start – passenger compartment fuse panel 70 20A* PCM (sensors) – EFC, A/C clutch coil 71 5A* Fuel coil, ISP-R 72 20A* PC[...]

The use of tire sealants may damage your tires. The use of tire sealants may also damage your T ire Pressure Monitoring System. Refer to T ire Pressure Monitoring System (TPMS) in the T ires, Wheels and Loading chapter for important information. If the tire pressure monitor sensor becomes damaged, it will no longer function. Dissimilar spare tire/w[...]

Use of one of the dissimilar spare tires listed above at any one wheel location can lead to impairment of the following: • Handling, stability and braking performance • Comfort and noise • Ground clearance and parking at curbs • W inter weather driving capability • W et weather driving capability For vehicles equipped with 4WD, it is not [...]

Stopping and securing the vehicle 1. Park on a level surface, activate the hazard flashers and set the parking brake. 2. Place the gearshift in P (Park) and turn the engine OFF . Spare tire information Note: The tire pressure monitoring system (TPMS) indicator light will illuminate when the spare is in use. T o restore the full functionality of the[...]

Removing the jack and tools 1. Open the liftgate, then locate the access panel on the floor behind the 3rd row seat. Unlatch and remove the panel. 2. Remove the jack and tools assembly tray from the compartment by turning the wing-nut counterclockwise to relieve tension against the jack assembly tray . Remove the bag from the jack and tool assembly[...]

Tire change procedure T o help prevent the vehicle from moving when you change a tire, be sure the parking brake is set, then block the wheels (both front or both rear) on the opposite end of the vehicle from the wheel being changed. If on a grade, block both opposite wheels on the downward side of the hill. If the vehicle slips off the jack, you o[...]

2. Place gearshift lever in P (Park), turn engine OFF and block the wheels (both front or both rear) on the opposite end of the vehicle from the wheel being changed. If on a grade, block both wheels on the downward side of the hill. 3. T urn off the air suspension system (if equipped - the air suspension system is controlled through the message cen[...]

When one of the rear wheels is off the ground, the transmission alone will not prevent the vehicle from moving or slipping off the jack, even if the transmission is in P (Park). T o prevent the vehicle from moving when you change the tire, be sure that the parking brake is set and block the wheels (both front or both rear) on the opposite end of th[...]

T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the front or rear differential as a jacking point. 8. Remove the lug nuts with the lug wrench. 9. Replace the flat ti[...]

Stowing the spare tire 1. Lay the tire on the ground, near the rear of the vehicle, with the valve stem side facing up. 2. Slide the wheel partially under the vehicle and install the retainer through the wheel center . If equipped, you may have to remove the wheel center cap prior to pushing the retainer through the center of the wheel. T o remove [...]

WHEEL LUG NUT TORQUE SPECIFICATIONS Retighten the lug nuts to the specified torque within 100 miles (160 km) after any wheel disturbance (tire rotation, changing a flat tire, wheel removal, etc.). Bolt size Wheel lug nut torque* lb.ft. N • m M14 x 2.0 150 200 * T orque specifications are for nut and bolt threads free of dirt and rust. Use only Fo[...]

1. Use only a 12–volt supply to start your vehicle. 2. Do not disconnect the battery of the disabled vehicle as this could damage the vehicle’ s electrical system. 3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine c[...]

2. Connect the other end of the positive (+) cable to the positive (+) terminal of the assisting battery . 3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . + – + – + – + – 2007 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies 307[...]

4. Make the final connection of the negative (-) cable to the jump starting stud located in the rear of the engine compartment, behind the battery . Do not use fuel lines, engine rocker covers or the intake manifold as grounding points. Do not connect the end of the second cable to the negative (-) terminal of the battery to be jumped. A spark may [...]

Removing the jumper cables Remove the jumper cables in the reverse order that they were connected. 1. Remove the jumper cable from the jump starting stud. Note: In the illustrations, lightning bolts are used to designate the assisting (boosting) battery . + – + – 2007 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies [...]

2. Remove the jumper cable on the negative (-) connection of the booster vehicle’ s battery . 3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . + – + – + – + – 2007 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus) Roadside Emergencies 310[...]

4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle conditions. + – + – 2007 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus) Roadside Eme[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member of a roadside assistance program, your roadside assistance service provider . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a sl[...]

If the vehicle is towed by other means or incorrectly , vehicle damage may occur . W ith a disabled vehicle (without access to wheel dollies, car hauling trailer or flatbed transport vehicle) your vehicle can be towed (all wheels on the ground) under the following conditions: Special Conditions: • Release the parking brake. • T urn the air susp[...]

GETTING THE SERVICES YOU NEED At home Y ou must take your Ford vehicle to an authorized dealer for warranty repairs. While any authorized dealer handling your vehicle line will provide warranty service, we recommend you return to your selling authorized dealer who wants to ensure your continued satisfaction. Please note that certain warranty repair[...]

In Canada: Customer Relationship Centre Ford Motor Company of Canada, Limited P .O. Box 2000 Oakville, Ontario L6J 5E4 1-800-565-3673 (FORD) www .ford.ca If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the authorized dealer could provide, after following the steps described above, c[...]

In some states (in the U.S.) you must directly notify Ford in writing before pursuing remedies under your state’ s warranty laws. Ford is also allowed a final repair attempt in some states. In the United States, a warranty dispute must be submitted to the BBB AUTO LINE before taking action under the Magnuson-Moss W arranty Act, or to the extent a[...]

THE BETTER BUSINESS BUREAU (BBB) AUTO LINE PROGRAM (U.S. ONLY) Y our satisfaction is important to Ford Motor Company and to your dealer . Experience has shown that our customers have been very successful in achieving satisfaction by following the three-step procedure outlined on the front page of the W arranty Guide. However , if your warranty conc[...]

UTILIZING THE MEDIATION/ARBITRATION PROGRAM (CANADA ONLY) For vehicles delivered to authorized Canadian dealers. In those cases where you continue to feel that the efforts by Ford of Canada and the authorized dealer to resolve a factory-related vehicle service concern have been unsatisfactory , Ford of Canada participates in an impartial third part[...]

If you did not take advantage of the Ford Extended Service Plan at the time of purchasing your vehicle, you may still be eligible. Since this information is subject to change, please ask your authorized dealer for complete details about Ford Extended Service Plan coverage options, or visit the Ford ESP website at www .ford-esp.com. GETTING ASSIST A[...]

ORDERING ADDITIONAL OWNER’S LITERA TURE T o order the publications in this portfolio, contact Helm, Incorporated at: HELM, INCORPORA TED P .O. Box 07150 Detroit, Michigan 48207 Or call: For a free publication catalog, order toll free: 1-800-782-4356 Monday-Friday 8:00 a.m. - 6:00 p.m. EST Helm, Incorporated can also be reached by their website: w[...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect which could cause a crash or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

W ASHING THE EXTERIOR W ash your vehicle regularly with cool or lukewarm water and a neutral pH shampoo, such as Motorcraft Detail W ash (ZC-3-A), which is available from your authorized dealer . • Never use strong household detergents or soap, such as dish washing or laundry liquid. These products can discolor and spot painted surfaces. • Neve[...]

• After polishing chrome bumpers, apply a coating of Motorcraft Premium Liquid W ax (ZC-53-A), available from your authorized dealer , or an equivalent quality product to help protect from environmental effects. W AXING Applying Motorcraft Paint Sealant (ZC-45) to your vehicle every six months will assist in reducing minor scratches and paint dam[...]

• T o remove tar and grease, use Motorcraft Bug and T ar Remover (ZC-42), available from your authorized dealer . ENGINE Engines are more efficient when they are clean because grease and dirt buildup keep the engine warmer than normal. When washing: • T ake care when using a power washer to clean the engine. The high-pressure fluid could penetr[...]

• For plastic headlamp lenses, use Motorcraft Ultra Clear Spray Glass Cleaner (ZC-23). WINDOWS AND WIPER BLADES The windshield, rear and side windows and the wiper blades should be cleaned regularly . If the wipers do not wipe properly , substances on the vehicle’ s glass or the wiper blades may be the cause. These may include hot wax treatment[...]

• Be certain to wash or wipe your hands clean if you have been in contact with certain products such as insect repellent and suntan lotion in order to avoid possible damage to the interior painted surfaces. • Do not use household or glass cleaners as these may damage the finish of the instrument panel, interior trim and cluster lens. Do not use[...]

Do not use cleaning solvents, bleach or dye on the vehicle’ s safety belts, as these actions may weaken the belt webbing. Do not use chemical solvents or strong detergents when cleaning the seat-mounted side airbag (if equipped). Such products could contaminate the side airbag system and affect performance of the side airbag in a collision. CLEAN[...]

materials that meet or exceed rigid specifications. For best results, use the following products or products of equivalent quality: Motorcraft Bug and T ar Remover (ZC-42) Motorcraft Car Care Kit (ZC-26) Motorcraft Car W ash (Canada only) (CXC-21) Motorcraft Custom Bright Metal Cleaner (ZC-15) Motorcraft Custom Clear Coat Polish (ZC-8-A) Motorcraft[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle, we provide scheduled maintenance information which makes tracking routine service easy . If your vehicle requires professional service, your authorized dealer can provide the necessary parts and service. Check your W arranty Guide to find out which parts and services are covered. Use only r[...]

OPENING THE HOOD 1. Inside the vehicle, pull the hood release handle located under the bottom of the instrument panel. 2. Go to the front of the vehicle and release the auxiliary latch that is located under the front center of the hood. 3. Lift the hood until the lift cylinders hold it open. 2007 Expedition (exd) Owners Guide (post-2002-fmt) USA (f[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 5.4L 3V–V8 engine 1. W indshield washer fluid reservoir 2. Engine oil dipstick 3. Brake fluid reservoir 4. Engine coolant reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Power distribution box 8. Engine oil filler cap 9. Battery 2007 Expedition (exd) Owners Guide (post-2002-fm[...]

WINDSHIELD WASHER FLUID Add fluid to fill the reservoir if the level is low . In very cold weather , do not fill the reservoir completely . Only use a washer fluid that meets Ford specification WSB-M8B16-A2. Do not use any special washer fluid such as windshield water repellent type fluid or bug wash. They may cause squeaking, chatter noise, streak[...]

CHANGING THE WIPER BLADES It is recommended that wiper blades are renewed before winter . T o replace the wiper blades: 1. Fold back the wiper arm and position the wiper blade at right angles to the wiper arm. 2. T o remove, press the retaining clip (A) to disengage the wiper blade, then pull the blade down toward the windshield to remove it from t[...]

ENGINE OIL Checking the engine oil Refer to the scheduled maintenance information for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. T urn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Pa[...]

• If required, add engine oil to the engine. Refer to Adding engine oil in this chapter . • Do not overfill the engine with oil. Oil levels above this mark may cause engine damage. If the engine is overfilled, some oil must be removed from the engine by an authorized dealer . 7. Put the indicator back in and ensure it is fully seated. Adding en[...]

Engine oil and filter recommendations Look for this certification trademark. Use SAE 5W -20 engine oil Only use oils “Certified For Gasoline Engines” by the American Petroleum Institute (API). An oil with this trademark symbol conforms to the current engine and emission system protection standards and fuel economy requirements of the Internatio[...]

BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. If your battery has a cover/shield, make sure it is reinstalled after the battery has been cleaned or replaced. For longer , trouble-free operation, keep the top of the battery clean and dry . Als[...]

Keep batteries out of reach of children. Batteries contain sulfuric acid. A void contact with skin, eyes or clothing. Shield your eyes when working near the battery to protect against possible splashing of acid solution. In case of acid contact with skin or eyes, flush immediately with water for a minimum of 15 minutes and get prompt medical attent[...]

• If you do not allow the engine to relearn its idle trim, the idle quality of your vehicle may be adversely affected until the idle trim is eventually relearned. If the battery has been disconnected or a new battery has been installed, the clock and the preset radio stations must be reset once the battery is reconnected. • Always dispose of au[...]

When the engine is cold, check the level of the engine coolant in the reservoir . • The engine coolant should be at the “FULL COLD” level or within the “COLD FILL RANGE” as listed on the engine coolant reservoir (depending upon application). • Refer to scheduled maintenance information for service interval schedules. • Be sure to read[...]

Note: Use of Motorcraft Cooling System Stop Leak Pellets or an equivalent product meeting Ford specification WSS-M99B37-B6, may darken the color of Motorcraft Premium Gold Engine Coolant from yellow to golden tan. • Do not add/mix an orange-colored, extended life coolant such as Motorcraft Specialty Orange Engine Coolant, meeting Ford specificati[...]

Add the proper mixture of coolant and water to the cooling system by following these steps: 1. Before you begin, turn the engine off and let it cool. 2. When the engine is cool, wrap a thick cloth around the coolant pressure relief cap on the coolant reservoir (a translucent plastic bottle). Slowly turn cap counterclockwise (left) until pressure be[...]

Coolant refill capacity T o find out how much fluid your vehicle’ s cooling system can hold, refer to Maintenance product specifications and capacities in this chapter . Fill your engine coolant reservoir as outlined in Adding engine coolant in this section. Severe climates If you drive in extremely cold climates (less than –34°F [–36°C ]):[...]

How fail-safe cooling works If the engine begins to overheat: • The engine coolant temperature gauge will move to the red (hot) area. • The symbol will illuminate. • The indicator light will illuminate. If the engine reaches a preset over -temperature condition, the engine will automatically switch to alternating cylinder operation. Each disa[...]

FUEL FILTER For fuel filter replacement, see your authorized dealer . Refer to scheduled maintenance information for the appropriate intervals for changing the fuel filter . Replace the fuel filter with an authorized Motorcraft part. The customer warranty may be void for any damage to the fuel system if an authorized Motorcraft fuel filter is not u[...]

• Automotive fuels can be harmful or fatal if swallowed. Fuel such as gasoline is highly toxic and if swallowed can cause death or permanent injury . If fuel is swallowed, call a physician immediately , even if no symptoms are immediately apparent. The toxic effects of fuel may not be visible for hours. • A void inhaling fuel vapors. Inhaling t[...]

Refueling Fuel vapor burns violently and a fuel fire can cause severe injuries. T o help avoid injuries to you and others: • Read and follow all the instructions on the pump island; • T urn off your engine when you are refueling; • Do not smoke if you are near fuel or refueling your vehicle; • Keep sparks, flames and smoking materials away [...]

the fuel filler cap, align the cap properly and reinstall it. The lamp will not reset immediately . Upon restarting the vehicle, it may take a few driving cycles (mileage accumulation) to clear the symbol. Continued driving with this lamp illuminated may cause the lamp to activate. If you must replace the fuel filler cap, replace it with a fuel fil[...]

Repairs to correct the effects of using a fuel for which your vehicle was not designed may not be covered by your warranty . Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with pump (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratin[...]

Running out of fuel A void running out of fuel because this situation may have an adverse effect on powertrain components. If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling to allow the fuel system to pump the fuel from the tank to the engine. On restarting, cranking time will take a f[...]

For consistent results when filling the fuel tank: • T urn the engine/ignition switch to the off position prior to refueling, an error in the reading will result if the engine is left running. • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow no more than two automatic click-offs when filling.[...]

Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel e[...]

• Adding certain accessories to your vehicle (for example; bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy . • Using fuel blended with alcohol may lower fuel economy . • Fuel economy may decrease with lower temperatures during the first 8–10 miles (12–16 km) of driving. • Driving on flat t[...]

If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivalent to genuine Ford Motor Company parts in performance and durability . Do not park, idle, or drive your vehicle in dry grass or other dry ground cover . The emis[...]

Examples are: 1. The vehicle has run out of fuel—the engine may misfire or run poorly . 2. Poor fuel quality or water in the fuel—the engine may misfire or run poorly . 3. The fuel cap may not have been securely tightened. See Fuel filler cap in this chapter . 4. Driving through deep water—the electrical system may be wet. These temporary mal[...]

eight times, it means that the vehicle is not ready for I/M testing; if the indicator stays on solid, it means that the vehicle is ready for I/M testing. The OBD-II system is designed to check the emission control system during normal driving. A complete check may take several days. If the vehicle is not ready for I/M testing, the following driving[...]

BRAKE FLUID The fluid level will drop slowly as the brakes wear , and will rise when the brake components are replaced. Fluid levels between the “MIN” and “MAX” lines are within the normal operating range; there is no need to add fluid. If the fluid levels are outside of the normal operating range the performance of the system could be comp[...]

Changing the air filter element 1. Locate the Mass Air Flow Sensor electrical connector on the air outlet tube. This connector will need to be unplugged. 2. Reposition the locking clip on the connector (connector shown from below for clarity), squeeze the connector and pull it off of the air outlet tube. 3. Clean the area around the air tube to air[...]

5. Release the three clamps that secure the cover to the air filter housing. Push the air filter cover toward the center of the vehicle and up slightly to release it. 6. Remove the air filter element from the air filter housing. 7. Install a new air filter element. 8. Replace the air filter housing cover and secure the clamps. Be careful not to cri[...]

10. Reconnect the Mass Air Flow Sensor electrical connector to the outlet tube. Make sure the locking tab on the connector is in the “locked” position (connector shown from below for clarity). Note: Failure to use the correct air filter element may result in severe engine damage. The customer warranty may be void for any damage to the engine if[...]

Replace the spark plugs with ones that meet Ford material and design specifications for your vehicle, such as Motorcraft or equivalent replacement parts. The customer warranty may be void for any damage to the engine if such spark plugs are not used. MOTORCRAFT PART NUMBERS 1 For spark plug replacement, see your authorized dealer . Refer to schedul[...]

MAINTENANCE PRODUCT SPECIFICATIONS AND CAPACITIES Item Capacity Ford part name Ford part number / Ford specification Brake fluid Between MIN and MAX on reservoir Motorcraft High Performance DOT 3 Motor V ehicle Brake Fluid PM-1-C / WSS-M6C62-A Hinges, latches, striker plates and rotors, seat tracks, fuel filler door hinge and spring — Multi-Purpo[...]

Item Capacity Ford part name Ford part number / Ford specification Engine coolant (Base radiator without aux rear heat) 20.6 quarts (19.5L) Motorcraft Premium Gold Engine Coolant (yellow-colored) 1 VC-7-B / WSS-M97B51-A1 Engine coolant (Heavy-duty trailer tow radiator without aux rear heat) 21.1 quarts (20.0L) Engine coolant (Base radiator with aux[...]

Item Capacity Ford part name Ford part number / Ford specification Power steering fluid Fill between MIN and MAX lines on reservoir Motorcraft MERCON 威 V AT F XT -5-QM / MERCON 威 V Front axle fluid (4X4) 3.5-3.7 pints (1.8-2.0L) Motorcraft SAE 80W -90 Premium Rear Axle Lube XY -80W90-QL / WSP-M2C197-A Rear axle fluid –Conventional differentia[...]

Item Capacity Ford part name Ford part number / Ford specification Fuel tank (Expedition Max – Canada only) 33.5 gallons (126.8L) 1 Add the coolant type originally equipped in your vehicle. 2 Use of synthetic or synthetic blend motor oil is not mandatory . Engine oil need only meet the requirements of Ford specification WSS-M2C930-A and the API C[...]

ENGINE DATA Engine 5.4L V8 engine Cubic inches 330 Required fuel 87 octane Firing order 1-3-7-2-6-5-4-8 Ignition system Coil on plug Spark plug gap 1 0.040–0.050 inch (1.02–1.27 mm) Compression ratio 9.85:1 1 Spark plug gap not adjustable Engine drivebelt routing • 5.4L V8 Engine 2007 Expedition (exd) Owners Guide (post-2002-fmt) USA (fus) Ma[...]

IDENTIFYING YOUR VEHICLE Safety Compliance Certification Label The National Highway T raffic Safety Administration Regulations require that a Safety Compliance Certification Label be affixed to a vehicle and prescribe where the Safety Compliance Certification Label may be located. The Safety Compliance Certification Label is located on the structur[...]

The V ehicle Identification Number (VIN) contains the following information: 1. W orld manufacturer identifier 2. Brake system / Gross V ehicle W eight Rating (GVWR) / Restraint System 3. V ehicle line, series, body type 4. Engine type 5. Check digit 6. Model year 7. Assembly plant 8. Production sequence number T RANSMISSION/T RANSAXLE CODE DESIGNA[...]

GENUINE FORD ACCESSORIES FOR YOUR VEHICLE A wide selection of Genuine Ford Accessories are available for your vehicle through your local Ford or Ford of Canada dealer . These quality accessories have been specifically engineered to fulfill your automotive needs; they are custom designed to complement the style and aerodynamic appearance of your veh[...]

Peace of mind Mobile-Ease 娂 hands-free communication system Remote start V ehicle security systems Wheel locks For maximum vehicle performance, keep the following information in mind when adding accessories or equipment to your vehicle: • When adding accessories, equipment, passengers and luggage to your vehicle, do not exceed the total weight [...]

A ABS (see Brakes) ..................... 257 Accessory delay ........................ 102 AdvanceT rac .............................. 260 Air cleaner filter ................... 357–358, 360–361 Air suspension ...........................265 description .............................. 265 Airbag supplemental restraint system ........192, 196, 198 [...]

in front seat ............................207 in rear seat ...................... 207, 210 Child safety seats - booster seats ............................. 202 Cleaning your vehicle engine compartment .............. 324 instrument panel ....................325 interior ............................. 326–327 plastic parts ..........................[...]

change oil soon warning, message center ....................... 334 checking and adding .............. 334 dipstick .................................... 334 filter , specifications .......... 336, 360–361 recommendations ................... 336 refill capacities ........................ 362 specifications .......................... 362 Event data[...]

Infant seats (see Safety seats) ..................... 206 Inspection/maintenance (I/M) testing .............................. 355 Instrument panel cleaning ................................... 325 cluster ........................................ 12 lighting up panel and interior ....................................... 85 J Jack .....................[...]

P Panic alarm feature, remote entry system .............................. 150 Parking brake ............................ 259 Parts (see Motorcraft parts) ......360–361 Pedals (see Power adjustable foot pedals) ............. 105 Power adjustable foot pedals ...105 Power distribution box (see Fuses) ....................... 289, 291 Power door locks[...]

Spare tire (see Changing the T ire) ...................298 Spark plugs, specifications ............. 360–361, 366 Special notice utility-type vehicles .................... 8 Specification chart, lubricants ................................... 362 Speed control ............................ 105 Starting your vehicle ........ 253–255 jump starting [...]