Furuno PP-505 инструкция обслуживания

PRINTER PP-505 (For FE-700)[...]

i SAFETY INSTR UCTIONS WARNING Do not open the cover of the equipment. This equipment uses high voltage electricity which can shock or burn. Only qualified personnel should work inside the equipment. Do not disassemble or modify the equipment. Fire, electrical shock or serious injury can result. Immediately turn off the power at the ship's mai[...]

ii A warning label is attached to the printer. Do not remove the label. If the label is missing or damaged, contact your dealer about replacement. WARNING To avoid electrical shock, do not remove cover. No user-serviceable parts inside. Name: Warning Label (1) Type: 86-003-1011 Code No.: 100-236-231 WARNING LABEL[...]

iii FOREWORD A Word to th e Owner of the PP -5 05 Congratulat ions on your choice of the FURUNO PP-505 Printer . For over 50 years FURUNO Electric Company has enjoyed an enviable reputation for innovative and dependable marine electronics equipment. This dedication to excellence is furthered by our extensive global network of agents and dealers. Y [...]

iv T ABLE OF CONTENTS 1. OPERA TION .................................................................................................. 1 1.1 General .................................................................................................................... .......... 1 1.2 P anel ............................................................[...]

1 1. OPERA TION 1.1 General Operation of the PP-505 is simple; just turn on the power . The depth graph or the log, whichever is selected for printing, is printed out at the interval set. Below are example printouts. 60m 80m 100m 20m 40m Marker 2003/12/01 13:05:00 038.6m/01.0m 35 20.02’N/135 45.15’E 15.1kt 008.0deg 2003/12/01 13:05:00 038.6m/01[...]

OPERA TION 2 Changing the mode Press the [MODE] k ey to change t he printing mode from depth graph to log printing alternately . The printing inter val setting is pr inted whenever the [MODE] key is pressed. Changing the printing interval Press the [I NTER V AL] key t o choose printing interv al . Depth graph: 9 s → 45 s → 90 s → 450 s Log: 1[...]

3 2. REPLACEMENT OF THERMAL PA P E R W hen the thermal paper runs out, the P APER LED blinks, pr inting stops automatically and the audible alarm sounds for five seconds. W ith 1 m of pape r remaining, a red paper end mark appears on the p aper . W hen the red mark appears, replace the thermal paper as shown in the procedure below . REQUIRED T HERM[...]

4 3. INST ALLA TION 3.1 Complete Set Name Type Mass Qty Remark Main Unit PP-505 3.1 kg (with hanger) 1 Spare Parts SP08-01600 1 Installation Materials CP16-00800 1 Accessories FP08-00500 1 Flush Mount Kit OP08-4 1 Option (004-511-330) 3.2 Ge nera l Mount ing Considera tions This equipment can perform its intended functions only if it is installed p[...]

3. IN ST ALLA TION 5 3.3 T abletop/Bulkhead Mount The m ain uni t can be m ounted on a desktop, bulkhead, or in a p anel. M ake sur e the selec ted loc ation i s str ong enough to suppor t the mai n unit agai nst poss ibl e vi brati on and shock . I f necessary , appropr iate rei nforcem ent meas ures should be m ade on the mounti ng area. T abl e [...]

3. INST ALLA TION 6 1. Referring to the illustration below , prepare a cutout in the mounting area and drill four pilot holes f or the flush mount angles. Refer to the outline dra wing at end of m anual. 2. Fix the liner and the flus h mount angles to the main unit. 3. Connect the cables at the rear o f main unit. 4. Fix the main unit to the p anel[...]

7 4. MAINTENANCE Checking the power connector Check for loosened or disconnected pow er connector . WARNING Do not open the cover of the equipment. This equipment uses high voltage electricity which can shock or burn. Only qualified personnel should work inside the equipment. Do not disassemble or modify the equipment. Fire, electrical shock or ser[...]

A P-1 APPENDIX REPLACEMENT OF PRINTER ASSEMBL Y/TERMAL HEAD 1. Loosen the four M4 × 15 screws fixing the rear cabinet to the main unit assembly . 2. Disconnect the connecto rs connected to the rear cabinet to detac h the rear cabinet. Rear Cabinet Main Unit Assembly P1 NH 4P P5 NH 6P M4 × 15 screw (4 pcs.) 3. Separate the p anel assembly from the[...]

A P-2 6. Pull out the connector end o f the flexible cable from the connector . T ake care not to damage the flexible cabl e. End of Fle xible Cable (Connector) 180 ° 7. Remove the thermal head from the head holder with a screwdriv er as shown below , and then take the t hermal head assembly out of the printer assembly . Thermal Head Head Holder S[...]

A P-3 1 1. Fix the flexible cable to the carriage w ith the flexible cable support, inserting the projection on the carriage into the hole o f the cable. Fle xible Cab le Suppor t Carriage Projection 12. Fold back the end of the cable and insert it into the connector . End of Fle xible Cable 180 °[...]

FURUNO SP - 1 E5540S03- 1 SPECIFICA TIONS OF PRINT ER PP-505 1 DATA FORM A T 1.1 Receiv ing Syste m RS-232 C 1.2 Speed 9600 bps 1.3 Data Lengt h 8 bits 1.4 Parity Non 1.5 Stop Bit 1 bit 2 PRINTER SEC TION 2.1 Printing Sy stem 9 dots serial ther mal head printing sy stem 2.2 Charact er Alphanu meric 2.3 Dot Pitch 0.28 mm/ dot 2.4 Number of Dot i n L[...]

[...]

Takahashi T . Takahashi T .[...]

Takahashi T . Takahashi T .[...]

2 4 3 A 1 B C DRAWN CHECKE D APPROV ED DWG.No . TITLE NAME 名称 相互結線図 INTERCONNECTIO N DIAGRAM PRINTER 08S008 7 1 2 SHIP'S MA INS 船内電源 12-32 V DC 5 4 3 2 1 6 7 RXD (H) TXD (H) TXD (C) RXD (C) 0V +12V N.C. FM14-2P 08S0157 4 6 5 EIA232 -TD EIA232 -RD GND DISTRIBUT ION BOX 分配箱 FE-702 TB1 FM14-7 P *2 *3 1. LOCAL S UPPLY .[...]