Grizzly H5570 инструкция обслуживания

COPYRIGHT © SEPT, 2003 BY GRIZZLY INDUSTRIAL, INC. WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC. PRINTED IN TAIWAN ONLINE MANUAL DISCLAIMER THE INFORMATION IN THIS MANUAL REPRESENTS THE CONFIGURATION OF THE MACHINE AS IT IS CURRENTLY BEING SHIPPED. THE MACHINE CON[...]

For Your Own Safety Read Instruction Manual Before Operating This Equipment Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. Indicates a potentially hazardous situation which, if not a[...]

H5570 18 Gauge Finish Angle Nailer -2 - 10. USE PROPER AIR HOSE for the tool. Make sure your air hose is in good condition and is long enough to reach your work without stretching. 11. WEAR PROPER APPAREL. DO NOT wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Non-slip footwear is reco[...]

H5570 18 Gauge Finish Angle Nailer -3 - Operating this nailer can propel objects into the air, causing immedi- ate eye damage. To protect yourself, always wear American National Standards Institute (ANSI) approved safety glasses or goggles when oper- ating this equipment. In addition, this nailer discharges at 85-90 decibels. To protect your hearin[...]

H5570 18 Gauge Finish Angle Nailer -4 - INTRODUCTION Commentary Most importantly, we stand behind our tools. If you have any service questions or parts requests, please call or write us at the location listed below. Grizzly Industrial, Inc. 1203 Lycoming Mall Circle Muncy, PA 17756 Phone: (570) 546-9663 Fax: (800) 438-5901 E-Mail: techsupport@grizz[...]

H5570 18 Gauge Finish Angle Nailer -5 - Compressed Air System Safety Yoke Mechanism The safety yoke is a mechanical device that can fail. Never rely on the safety yoke mechanism as an excuse to point the nailer at yourself or any bystanders. Serious injury may occur. Exceeding the maximum permissible operating pressure may cause the nailer to explo[...]

Oiling Nailer Special oil has been included with your new Grizzly nailer to help maintain its use- ful life. Place one drop of oil in the nailer air inlet (as shown in Figure 1 ) before every use. Wipe off any excess oil near the nail- er exhaust to avoid dust build-up. When the oil that was included with the nailer has been completely used, replac[...]

H5570 18 Gauge Finish Angle Nailer -7 - Operating Nailer If you have not read the safety instruc- tions in this manual, DO NOT operate the nailer. Before you operate your nailer, place one drop of the included oil into the quick con- nect fitting where the nailer connects to the air supply. To operate your nailer: 1. Connect the air supply to the q[...]

Always disconnect air from nailer whenever clearing a jammed nail! H5570 18 Gauge Finish Angle Nailer -8 - To clear a jammed nail from the dis- charge area on the Model H5570: 1. Disconnect the nailer from the air supply! 2. Pull the spring loaded pusher all the way back and remove the nail stick. 3. Flip up the quick release latch located on top o[...]

H5570 18 Gauge Finish Angle Nailer -9 - Replacing Pistons/O-Rings If you use your nailer day in and day out, Grizzly offers repair pistons as cheap insurance against wasted down time and lost profits in the event that a piston or pis- ton shaft becomes worn out. Figure 8. Removing rear cap. 5. The top of the piston should now be visible inside the [...]

H5570 18 Gauge Finish Angle Nailer -10 - H5570 PART BREAKDOWN[...]

H5570 18 Gauge Finish Angle Nailer -11 - 01 PSB113M BTN CAP SCR M5-.8 X 11 02 PH5570002 EXHAUST COVER 03 PH5570003 SEAL 04 PSB15M CAP SCREW M5-.8 X20 05 PSS08M SET SCREW M4-.7 X 5 06 PH5570006 CAP 07 PH5570007 PISTON STOPPER 08 PH5570008 O RING 09 PH5570009 COLLAR 10 PH5570010 O RING 11 PH5570011 SPRING 12 PH5570012 PISTON HEAD VALVE 13 PH5570013 S[...]

1. O-rings must be replaced & operation of safety yoke must be checked. 1. Tighten screws. 2. Replace O-ring. 3. Tighten air fitting. 1. Replace damaged seals. 1. Tighten screws and fit- tings. 2. Clean nose. 3. Clean magazine and inspect/repair damage. 4. Check fitting, hose, com- pressor & air pressure. 5. Replace piston O-ring. Lubricate[...]

H5570 18 Gauge Finish Angle Nailer -13 - Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of main- tenance. This is Grizzly’s[...]

Name __________________________________________________________ Street __________________________________________________________ City ____________________ State ________ Zip _________ Phone Number ____________ E-Mail ___________________ FAX ____________ Model # _______________Serial#________________ Order # ______________ The following information[...]

FOLD ALONG DOTTED LINE GRIZZLY INDUSTRIAL, INC. P.O. BOX 2069 BELLINGHAM, WA 98227-2069 TAPE ALONG EDGES--PLEASE DO NOT STAPLE Name________________________________ Street________________________________ City______________State______Zip_______ Send a Grizzly Catalog to a friend: Place Stamp Here[...]