Homelite EL14 инструкция обслуживания

FIRST EDITION PART NO. 101414-01 Printed in U.S.A. Price $1.00 WARNING ICON G 001 M R di I OWNER’S MANUAL ELECTRIC CHAINSA WS EL14 and EL16 ®[...]

2 101414 ELECTRIC CHAIN S A W SAFETY W ARNINGS BEFORE OPERATING SAW 1 . Read and understand this o wner’ s manual before operating chain saw . 2. W atch what you are doing. Use common sense. Do not operate saw when you are tired. 3. Use chain saw for cutting wood only . Do not use chain saw for purpose not intended. Do not use for cutting plastic[...]

3 101414 OWNER’S MANUAL KICKBACK WARNING: Kickback may occur when the nose or tip of the guide bar touches an object, or when the wood closes in and pinches the saw chain in the cut. Tip contact in some cases may cause a lightning fast reverse reaction, kicking the guide bar up and back towards the operator. Pinching the saw chain along the top o[...]

4 101414 ELECTRIC CHAIN S A W CHAIN SA W NAMES AND TERMS Bucking Process of cutting a felled tree or log into lengths. Felling Process of cutting down a tree. Felling Cut Final cut when felling a tree. Make this cut on opposite side of tree from notching cut. Front Handle Located at front of saw body. Front Hand Guard Shield between front handle an[...]

5 101414 OWNER’S MANUAL Power Cord Rear Hand Guard Rear Handle Front Hand Guard Guide Bar Spike Saw Chain Guide Bar Nose Scabbard Oil Cap Trigger Switch Lockout Motor Housing Figure 2 - Electric Chain Saw Oil Level Sight Hole (located on saw body, hidden by front handle) Front Handle PRODUCT IDENTIFICA TION UNP ACKING 1. Remo ve all items fr om c[...]

6 101414 ELECTRIC CHAIN S A W Mounting Stand-Outs Guide Bar Bolts Guide Bar Nuts Adjusting Hole Guide Bar Tapping Screw Saw Chain Cutting Edge Cutting Edge Towards Guide Bar Nose Front Hand Guard Drive Sprocket Figure 3 - Assembling Guide Bar, Chain, and Hand Guard Adjusting Plate Adjusting Screw Sprocket Support Figure 4 - Part Locations For Assem[...]

7 101414 OWNER’S MANUAL PUSH TO SHARPEN INSTALLING AUTOMATIC CHAIN SHARPENER (Fast Sharp Models Only) 1. Scr e w automatic chain sharpener into threaded hole. 2 . Continue turning automatic chain sharpener until you hear five (5) clicks. Automatic Chain Sharpener Figure 5 - Automatic Chain Sharpener (Fast Sharp Models Only) ASSEMBL Y Continued N[...]

8 101414 ELECTRIC CHAIN S A W CUTTING WITH THE CHAIN SAW 1. Connect saw to extension cord. Connect extension cord to po wer supply . 2. Make sure section of log to be cut is not laying on ground. T his will keep chain from touching ground as it cuts through log. T ouching ground with moving chain will dull chain. 3. Use both hands to grip saw . Alw[...]

9 101414 OWNER’S MANUAL Figure 13 - Felling A Tree Direction of Fall 2" 1st Cut - Lower Notch Cut 2nd Cut - Upper Notch Cut Hinge 2 Inches 3rd Cut - Felling Cut WARNING: Do not cut all the way through tree. Leave about two inches of tree diameter uncut directly behind felling notch (see Figure 13). This uncut portion acts as a hinge. The hin[...]

10 101414 ELECTRIC CHAIN S A W BUCKING A LOG Figure 15 - Bucking Log With Entire Length On Ground WARNING: Avoid kickback. Kickback can result in severe injury or death. See Kickback , page 2 to avoid risk of kickback. WARNING: • If on slope, make sure log will not roll down hill. Secure log by using wooden stakes. Drive wooden stakes into ground[...]

11 101414 OWNER’S MANUAL 1st Cut Figure 17 - Bucking Log When Log Is Supported On Both Ends 2nd Cut TRIMMING A TREE (Pruning) Figure 11 - Cutting A Limb WARNING: Avoid kickback. Kickback can result in severe injury or death. See Kickback , page 2 to avoid risk of kickback. WARNING: Do not operate chain saw while • in a tree • on a ladder or a[...]

12 101414 ELECTRIC CHAIN S A W CLEANING SAW BODY CLEANING AND MAINTENANCE Guide Bar With Uneven Wear Figure 18 - Guide Bar Cross Section Show- ing Uneven Bar Wear Guide Bar Groove Guide Bar NOTICE: Below are instructions for servicing your chain saw. Any servicing not mentioned below should be done by an authorized service center. WARNING: Unplug c[...]

13 101414 OWNER’S MANUAL WARNING: Unplug chain saw from power source before servicing. Severe injury or death could occur from electrical shock or body contact with moving chain. WARNING: Cutting edges on chain are sharp. Use protective gloves when handling chain. Figure 20 - File and File Guide Placement On Chain FILE HOLDER 30 ° Guide Mark Fil[...]

14 101414 ELECTRIC CHAIN S A W PUSH TO SHARPEN Filing Cutter Depth Gauges The cutter depth gauge clearance is reduced as cutters are sharpened. After every second or third sharpening, reset cutter depth gauges. 1. Place depth gauge tool (.025") firmly across top of two cutters. Make sure depth gauge enters slot in depth gauge tool (see Figure[...]

15 101414 OWNER’S MANUAL TROUBLE SHOOTING WARNING: Unplug chain saw from power source before servicing. Severe injury or death could occur from electrical shock or body contact with moving chain. OBSERVED FAULT Saw runs, but does not cut. Saw does not cut unless heavily forced. Cutting produces only sawdust with few large chips. Saw runs slow. Sa[...]

WARNING ICON G 001 SYMBOL DEFINITIONS G 018 M R di I THIS SAFE•T•TIP DEVICE ON YOUR BAR NOSE PRE- VENTS KICKBACK THIS SYMBOL INDICATES DANGER OR WARNING. DO NOT USE ONE-HANDED. HOLD SAW PROPERLY WITH BOTH HANDS. READ YOUR PRODUCT LITERATURE. DANGER! BEWARE OF KICKBACK. AVOID BAR NOSE CONTACT. WEAR HEARING AND EYE PROTECTION DEVICES. DIAGONAL LI[...]