Honeywell IPGSM-DP инструкция обслуживания

I I P P G G S S M M - - D D P P C C o o m m m m e e r r c c i i a a l l F F i i r r e e C C o o m m m m u u n n i i c c a a t t o o r r I I n n s s t t a a l l l l a a t t i i o o n n a a n n d d S S e e t t u u p p G G u u i i d d e e IPGSM-DP Commercial Fire Comm unicator RADIO TROUBLE LO W BA TT AC ON AC LOSS 800-08074 1/11 Rev. A[...]

Contents General Info rmation ............................................................................................................ ...........1 Package Contents ............................................................................................................... ........1 Compatible Fi re Panels ...................................[...]

IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 1 – General Information The IPGSM-DP Commercial Fire Comm unicator (henceforth referred to as IPGSM-DP) includes everything you need to upgrade a c ommercial fire system th at previously reported by POTS to a system that uses the Internet as its primary reporting path, an[...]

IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 2 – STEP 1 – Activate the SIM and Setup the Customer Account The communicator requires a subscriber account (customer account) to be setup with Alar mNet Direct. This is accomplished by registering th e communicator' s iGSM communications m odule with AlarmNet. Re[...]

IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 3 – STEP 3 – Determine the Signal Strength and Select a Location IMPORTANT - Do Not mount this de vice outdoors. RF Exposure Warning - The antenna(s) used for th is transmitter must be installed to provide a separati on distance of at least 20 cm from all persons and mu[...]

IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 4 – 3. Install the two plastic m ounting rails for th e LED Display board. Th ey simply snap into the back plate holes. 4. Connect the LED Dis play board to its connect or, then slide the board int o the mounting rails. (Yellow LED and Buzzer are on top.) 5. Carefully re[...]

IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 5 – IPGSM-DP-001-V2[US Only] TB 1 6 7 8 5 10 11 9 2 3 4 1 FOR EXTERNAL ANTENNA 50 OHM MMCX ONLY PRIMARY POWER: 9 - 16.5 VAC CURRENT: 900mA PEAK, 70mA STANDBY BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP FCC:XXXXXXXXXX IC: YYYYYYYYYY RSSI M0 M1 GPRS IBS 7720P PROGRAMMER PORT NOT [...]

IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 6 – STEP 5 – Program the Communications Module You must use the 7720P Programming tool to program the IPGSM-DP. When using the 7720P P rogramming tool, the valu es given below are for mo st installations. Press the [#] key to accept the displa yed default value ( xxx) [...]

IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 7 – To exit the progr amming mode, press [ N] in response to the "Review?" pr ompt. Then press [Y] to the "Exit Prog Mode?" prompt. Upon exiting, the ro ot file is updated to log the changes made. A message is dis played telling the user that this step[...]

IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 8 – IPGSM-DP Trouble Detection Information Telco 1 is used for th e Fire Panel to output con tact ID messages to the IPGSM-DP, an d Telco 2 is use d by the IPGSM-DP to report f aults to the Fire P anel. If Telco 1 is not operat ional, the Fire Pan el will use Telco 2 to [...]

IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 9 – Note: If a wire pulled out of the LED Board Connector refer to the diagram on right and reinsert wir e, ensuring the connector pin is locked in. PowerBoost1 Module Information LED Indicator STATUS AC (green) AC power available. ACTIVE (green) Cyclical flashing – nor[...]

IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 10 – iGSM Communications Module Information TB 1 6 7 8 5 10 11 9 2 3 4 1 PRIMARY POWER: 9 - 16.5 VAC CURRENT: 900mA PEAK, 70mA STANDBY BATTERY: 8V. 3.1 AHr FOR 24 Hr BACKUP FCC:XXXXXXXXXX IC: YYYYYYYYYY RSSI M0 M1 GPRS IBS iPGSM-COM-002-V1 RSSI / Mode and status LEDs ON [...]

IPGSM-DP Commercial Fire Communicato r – Installation and Setup Guide – 11 – RF Specifications Band Transmission Frequency (MHz) Transmit Power (dBm) Receive Frequency (MHz) Receive Sensitivity (dBm) Number of Channels Channel Spacing (MHz) Duplex Separation (kHz) GSM 850 824-849 33 869-894 -107 124 200 45 GSM 900 890-915 33 935-960 -107 124 [...]

IPGSM-DP Commercial Fire Communicato r – Installation and Se tup Guide – 12 – NOTES[...]

Wiring Diagram The wiring diagram below is depict ed for point-to-point electrical con nection checks used for tr oubleshootin g or componen t replacement. It is not in tended to show the phys ical routing of wires. When replacing a wire or componen t, ensure the wire is route d in the same manner as the orig inal factory wire. IPGSM-DP-007- V 2 [U[...]

FCC STATEMENT Note: This equipment has been tested and foun d to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits ar e designed to prov ide reasonable prot ection against harmful interference when the equipment is operated in a commerci al environment. This equipment generates, us es, and can r[...]