HP Z220 SFF инструкция обслуживания

HP Z220 SFF, Z220 CMT, Z420, Z620, and Z820 Workstations Maintenance and Service Guide[...]

Copyright Information © Copyright 2012, 2013 Hewlett-Packard Development Company, L.P Third Edition: February 2013 First Edition: April 2012 669531-003 Warranty Hewlett-Packard Company shall not be liable for technical or editorial errors or omissions contained herein or for incidental or consequential damages in conn ection with the furnishing, p[...]

About this guide This guide provides service and maintenance inform ation, technical details and configuration guidance for the HP Z220 SFF, Z220 CMT, Z420, Z6 20, and Z820 Workstatio ns. IMPORTANT: Removal and replacement procedures are now availabl e in videos on the HP website. Go to the HP Customer Self-Re pair Services Media Library at http://[...]

Table of contents 1 Ha rdware o verview ......... ........ .......... ......... .......... ......... .......... ......... .......... ........ ........... .. 1 HP Z220 SFF W orkstation c omponents .... ......... ............ ......... ........... ......... ............ ......... ............ 1 HP Z220 S FF Workstatio n front panel components .......[...]

Environmental specific ations ............. ............ ........... .......... .............. ........... ............ ........... .... .. 37 ENERGY ST AR qualific ation ........... .............. ..................... .............. .................... ............... ..... 37 Ensuring proper ventilation .... ............ .......... .......... .[...]

Changing a pow er-on or s etup passw ord ..................................... 72 Deleting a power-o n or setup pa ssword .......... ......... ........ ....... ..... 73 Nat ion al k ey boa rd d eli mit er cha rac ter s .... ............ .......... ............. 73 Clearing passwords ..... ........... ......... ........ ......... ........... .......[...]

Drive install ation and cabl ing scenarios ...................................................... 96 HP Z220 SFF Workstations — SATA cable connection guidelines . . . 96 HP Z220 CMT Workstations — SATA cable connection guidelines ................................................................................ 96 HP Z420 Workstations — Intel A[...]

Troubles hooting a pro blem ..... .............. ........... ............. ........... .............. .. 123 Instant Su pport and Ac tive Chat ........... .................. ............... ................... 123 Customer Advisories , Customer and Security Bulletins, and Cus tomer Notices 123 Product Cha nge Notifications .........................[...]

POST e rror messa ges ....................... ...................................... ............................... 154 5 Configur ing passw ord securi ty and res ettin g CMOS ......... ................. ................... ......... 159 Prepar ing to configure pa sswords .... .................. ............... .................. .............. ..[...]

Index . .......... ........ ........... ......... .......... ........ ........... ......... .......... ......... ........... ........ ...... ...... 1 86 xi[...]

1 Hardware overview This chapter presents an overview of workstation hard ware components. Topics HP Z220 SFF Works tation components on page 1 HP Z220 CMT Workstation components on page 8 HP Z420 Workstation components on page 15 HP Z620 Workstation components on page 23 HP Z820 Workstation components on page 30 Environmental specifications on pag[...]

HP Z220 SFF Workstation front panel components Figure 1-1 Front panel components Table 1-1 Component descri ption 1 Optical drive 5 Optional media card reader (shown) or optional second hard disk drive 2 Power button 6 Hard drive or optical drive activity light 3 USB 2.0 ports (4, black) 7 Headphones connector 4 Microphone or headphones connector ([...]

HP Z220 SFF Workstation rear panel components Figure 1-2 Rear pa nel components NOTE: The labels for the rear panel connectors use industry-standar d icons and colors. Table 1-2 Component desc riptions 1 RJ–45 network connect or 7 DisplayPort (DP) 2 Serial port 8 VGA (monitor) (blue) 3 PS/2 mouse connector (green ) 9 PS/2 keyboard connec tor (pur[...]

HP Z220 SFF Workstation chassis components For complete and current information on supported accessories and components for the computer, see http://partsurfer.hp.com . The following image shows the components of a typical computer layout. Drive configurations can vary. Figure 1-3 Chassis components Table 1-3 Component desc riptions 1 Access panel [...]

HP Z220 SFF Workstation system board component The following illustration and table identify computer system board components. Figure 1-4 System board comp onent locations Table 1-4 System board comp onent descriptions I/O SATA Power 1 Display Port 13 AHCI 3Gb/s 20 Battery 2 Front audio 14 AHCI 6Gb/s 21 CPU power 3 Front speaker NOTE: Only the port[...]

HP Z220 SFF Workstation system board architecture This section desc ribes the system archite ctures. The following figure shows the typical system board block diagram. Figure 1-5 System board block diagram NOTE: The PCIe designators indicate the mechanical connector size and number o f electrical PCIe lanes routed to an expansion slot. For example,[...]

Workstation specifications HP Z220 SFF Proces sor technology Intel Series C216 chipset: ● Support for the Intel® Xeon® Processor E3 v2 Fami ly, third-generation Intel Core processors u p to 95 W, or Intel Pentium® G640 procesors ● Integrated 2-channel memory con troller ● Microarchitecture improvements ● Integrated graphics (some models)[...]

HP Z220 CMT Workstation components For complete and current information on supported accessories and components for the computer, see http://partsurfer.hp.com . Topics HP Z220 CMT Workstation front panel components on page 9 HP Z220 CMT Workstation rear panel components on page 10 HP Z220 SFF Workstation chassis compon ents on page 4 HP Z220 SFF Wo[...]

HP Z220 CMT Workstation front panel components Figure 1-6 Front panel components Table 1-5 Component descripti ons 1 Optical drive 5 USB 3.0 ports (2) (blue) 2 Power button 6 Headphone connector 3 Hard drive activity light 7 Microphone connector 4 USB 2.0 ports (1) (black) 8 1394a FireWire® connector (optional and plugged unless configured) HP Z22[...]

HP Z220 CMT Workstation rear panel components Figure 1-7 Rear pa nel components Table 1-6 Component desc riptions 1 Power cord connector 9 Power supply Built-In Self Tes t (BIST) LED 2 PS/2 keyboard connector (purple) 10 PS/2 mou se connector (green) 3 DVI-I connector 11 Universal chassis clamp opening 4 Display Port (DP) conn ector 12 Cable lock s[...]

HP Z220 CMT Workstation chassis co mponents The following figu re shows the chassis componen ts of a typical HP Z220 CMT Workstation layout. Drive configurations can vary. Figure 1-8 Chassis components Table 1-7 Workstation component descriptions Item Descrip tion Item Descrip tion 1 Power supply 8 Memory module (DIMM) 2 Side access panel 9 PCIe ca[...]

HP Z220 CMT Workstation system board component The following illustration and table identi fy workstation system board components. Figure 1-9 System board comp onent locations Table 1-8 System board comp onent descriptions I/O SATA Power 1 Display Port 15 AHCI 3Gb/s 27 Battery 2 DVI video 16 AHCI 6Gb/s 28 CPU power 3 Front audio PCI/PCIe 29 Front p[...]

HP Z220 CMT Workstation system board architecture The following figure shows the typical system board block diagram. Figure 1-10 System board block diagram NOTE: The PCIe designators indicate the mechanical connector size and number o f electrical PCIe lanes routed to an expansion slot. For example, x16(8) means that the expansion slot is mechanica[...]

Workstation specifications HP Z220 CMT Proces sor technology Intel Series C216 chipset: ● Support for the Intel Xeon Processor E3 v2 Family or third-generation Intel Core processors up to 95 W ● Integrated 2-channel memory con troller ● Microarchitecture improvements ● Integrated graphics (some models) ● Advanced Vector Extensions (AVX) t[...]

HP Z420 Workstation components For complete and current information on supported accessories and components for the computer, see http://partsurfer.hp.com . Topics HP Z420 Workstation front panel on page 16 HP Z420 Workstation rear panel on page 17 HP Z420 Workstation chassis compon ents on page 18 HP Z420 Workstation system board components on pag[...]

HP Z420 Workstation front panel Figure 1-11 Front p anel components Table 1-9 Component desc riptions 1 Optical drive 5 USB 3.0 ports (2, blue) 2 Power button 6 Headphone connector 3 Hard drive activity light 7 Microphone connector 4 USB 2.0 port (black) 8 IEEE–1394a FireWire® connector 16 Chapter 1 Hardware overview[...]

HP Z420 Workstation rear panel Figure 1-12 Rear panel c omponents Table 1-10 Component descri ptions 1 Power supply Built-In Self Test (BIST) LED 9 Audio line-out connector (green) 2 Universal chassis clamp opening 10 Microphone connect or (pink) 3 PS/2 mouse connector (green ) 11 AMT-enabled RJ-45 network connector (orange) 4 USB 2.0 ports (4, bla[...]

HP Z420 Workstation chassis components Figure 1-13 Chassis components Table 1-11 Component descri ptions 1 Power supply 9 CPU 2 Side access panel 10 Memory module (DIMM) 3 Rear system fan 11 System board 4M e m o r y a i r f l o w g u i d e 1 2 P C I e c a r d 5 Hard disk drive 13 PCI card 6 Hard disk drive 14 Speaker 7 Optical drive 15 Front bezel[...]

HP Z420 Workstation system board components Figure 1-14 System board component locati ons Table 1-12 System board c omponent descriptions I/O SATA (SAS optional) Cooling Security 1 Front 1394a 14 AHCI 3Gb/s 25 CPU0 fan 34 Chassis solenoid lock 2 Front audio 15 AHCI 6Gb/s 26 Front fan 35 Chassis intrusion sensor 3 Front speaker 16 HDD LED 27 Memory [...]

HP Z420 Workstation system board architecture Figure 1-15 HP Z420 Workstat ion system board block diagra m NOTE: The PCIe designators indicate the mechanical connector size and number o f electrical PCIe lanes routed to an expansion slot. For example, x16(8) means that the expansion slot is mechanically a x16 length connector, with 8 PCIe lanes sup[...]

HP Z420 Workstation specifications Processo r technolog y Intel Series C602 chipset: ● Support for the Intel Xeon Processor E5-1600 Series and E5-2600 Series, including processors up to 150 W ● Integrated 4-channel memory con troller ● Microarchitecture improvements ● Large L3 cache for superior performance ● Intel QuickPath Interc onnect[...]

Weight ● Standard configuration: 13.2 kg (29.2 lb) ● Minimum configur ation: 12.5 kg (27.5 lb) ● Maximum configuration: 17.7 kg (39.4 lb) Chassis dimensions Tower configuration: ● Height: 44.76 cm (17.62 in) ● Width: 17.78 cm (7.00 in) ● Depth: 44.50 cm (17.53 in) Desktop configuration: ● Height: 17.78 cm (7.00 in) ● Width: 44.76 cm[...]

HP Z620 Workstation components For complete and current information on supported accessories and components for the computer, see http://partsurfer.hp.com . Topics HP Z620 Workstation front panel on page 23 HP Z620 Workstation rear panel on page 24 HP Z620 Workstation chassis compon ents on page 25 HP Z620 Workstation system board components on pag[...]

HP Z620 Workstation rear panel Figure 1-17 Rear panel c omponents Table 1-14 Component descri ptions 1 Power cord connector 8 Audio line-out connector (green) 2 PS/2 mouse connector (green ) 9 Microphone connector (pink) 3 USB 2.0 ports (4, black) 10 U SB 3.0 ports (2, blue) 4 RJ-45 network connectors (orange) Bottom connector is AMT enabled 11 IEE[...]

HP Z620 Workstation chassis components Figure 1-18 Chassis components Table 1-15 Component descripti ons 1 Side access panel 13 Second CPU memory m odule (DIMM) (optional) 2 Second CPU module rear guide bracket 14 CPU 3 Memory fan s 15 Second CPU module (option al) 4 Rear system fans 16 PCIe card 5 Power supply 17 PCI card 6 Speaker 18 Card guide a[...]

HP Z620 Workstation system board components Figure 1-19 System board component locati ons Table 1-16 System board c omponents descriptions I/O PCI/PCIe Power 1 Front 1394a 13 PCIe2 x4 (1) 25 Battery 2 Front audio 14 PCIe3 x1 6 26 CPU and memory power 3 Front USB 2.0 15 PCIe2 x8 (4) 27 Front power button, LED, speaker 4 Front USB 3.0 16 PCIe3 x8 28 [...]

Table 1-16 System board components descriptions (c ontinued) 12 Serial (optional) 23 CPU1 memory fan (optional) Service 24 Rear fan s 35 Clear CMOS button For related expansion card slot information, see Expansion slots on page 84 36 ME/AMT flash override 37 Password jum per HP Z620 Workstation system board architecture Figure 1-20 System board blo[...]

HP Z620 Workstation specifications Proces sor technology Intel Series C602 chipset: ● Support for the Intel Xeon Processor E5-1600 Series and E5-2600 Series ● Integrated 4-channel memory con troller ● Microarchitecture improvements ● Large L3 cache for superior performance ● Intel QuickPath Inte rconnect (QPI) connects processors and I/O [...]

Weight ● Standard configuration: 17.9 kg (39.4 lb) ● Minimum configur ation: 15.5 kg (34.2 lb) ● Maximum configuration: 22.6 kg (49.9 lb) Chassis dimensions ● Height: 44.45 cm (17.50 in) ● Width: 17.15 cm (6.75 in) ● Depth: 46.48 cm (18.30 in) HP Z620 Workstatio n components 29[...]

HP Z820 Workstation components For information on suppor ted ac cessories and compo nents, see h ttp://partsurfer.hp.com . Topics HP Z820 Workstation syst em bo ard architecture on page 34 HP Z820 Workstation chassis compon ents on page 32 HP Z820 Workstation front panel on page 30 HP Z820 Workstation rear panel on page 31 HP Z820 Workstation syste[...]

HP Z820 Workstation rear panel Figure 1-22 Rear panel c omponents Table 1-18 Component descri ptions 1 Power cord connector 9 USB 3.0 ports (2, blue) 2 PS/2 mouse connector (green ) 10 USB 2.0 ports (4, black) 3 Audio line-in conne ctor (blue) 11 Audio line-out connector (green) 4 RJ-45 network connectors (2, orange) Top connector is AMT enabled 12[...]

HP Z820 Workstation chassis components Figure 1-23 Chassis components Table 1-19 Component descri ptions 1 CPU/memory fans 12 Processor (CPU) heatsink 2 Power supply 13 Processo r (CPU) 3 Optical drive 14 Chassis 4 Side access panel 15 Processor (CPU) liquid cooling unit (optional u pgrade to standard heatsink) 5 Side access panel key lock 16 PCI R[...]

HP Z820 Workstation system board components Figure 1-24 System board component locati ons Table 1-20 System board c omponent descriptions I/O PCI/PCIe P ower 1 Front 1394 a 16 PCIe3 x8 (4) — CPU0 31 Battery 2 Front audio 17 PCIe3 x16 — CPU0 32 CPU0 power 3 Front USB 2.0 18 PCIe3 x16 (8) — CPU1 33 CPU1 power 4 Front USB 3.0 19 PCIe3 x16 — CP[...]

Table 1-20 System board com ponent descriptions (continued) 10 Serial 24 Aux iliary fan 2 (rear) 39 Crisis recovery jumper SAS/SATA 25 CPU/memory fans 40 ME/AMT Flash override 11 AHCI 6Gb/s 26 Front fan 1 (top) 41 Password jumper 12 Hard disk drive LED 27 Fron t fan 2 (bottom) NOTE: For related expansion card slot information, see Expansion slots o[...]

HP Z820 Workstation specifications Proces sor technology Intel Series C602 chipset: ● Support for the Intel Xeon Processor E5-2600 Series, including processors up to 150 W ● Integrated 4-channel memory con troller ● Microarchitecture improvements ● Large L3 cache for superior performance ● Intel QuickPath Inte rconnect (QPI) connects proc[...]

I/O technology ● SATA RAID 0/1/5/10 on SCU ● SAS RAID 0/1/10 on LSI SAS 2308 controller ● Six SATA ports: four SCU (3 GB/s) ; two AHCI (6 GB/s) ● Eight SAS po rts (6 GB/ s) ● Two ports (6.0 GB/s) available for optional eSATA ● Four external USB 3.0 ports ● Five external and six internal USB 2.0 ports Weight ● Standard configuration:[...]

Environmental specifications The following table lists the environmental specifications o f HP Workstations. Table 1-21 HP Workstation environmenta l specifications Temperature Operating : 5 to 35°C (40 to 95°F) Non-operating : -4 0 to 60°C (-40 to 140°F) NOTE: Derate by one degree C (1.8 degrees F) for every 305m (1,000 ft) altitude over 1,524[...]

Ensuring proper ventilation Proper ventilation for the system is important fo r workstation operatio n. Follow these guidelines: ● Operate the workstation on a sturdy, level surface. ● Provide at least 15.24 cm (6 inches) of cleara nce at the front and back of the workstation. (Workstation models vary.) Figure 1-26 Proper workstation ventilatio[...]

2 System management This section describes the tools and utilities that provide system ma nagement for the work station. Topics Power management and performance features on page 39 BIOS ROM on page 41 Computer Setup (F10) Utility on page 42 Desktop manageme nt on page 60 Power management and performance features ERP compliance mode This computer pr[...]

Hyper-Threading Technology (HTT) This computer supports HT T, an Intel-propriet ar y technology that improv es processor performa nce through parallelization of computations (doing multiple tasks at once). The operating system treats an HTT-en abled proc essor as two virtual proc esso rs, and sh ares the workload between them when pos sible. This f[...]

Non-Uniform Memory Access (NUMA) Non-Uniform Memory Acce ss (NUMA) is av ailable on some Z se ries Workstations. NUMA can improve memory bandwidth and la tency fo r multi-process or multi-thread ed applications or workloads. Observed performance improve ments depend on th e operating system, cu stomer workload , system configuration, and the degree[...]

Computer Setup (F10) Utility Topics Computer Setup (F10) functionality on page 42 Accessing Computer Setup (F10) Utility on page 43 Computer Setup (F10) Utility menu on page 44 Computer Setup (F10) functionality The Computer Setu p (F10) Utility enables you to: ● Update BIOS using a USB device. ● Change factory default settings and set or chan [...]

● Specify the Ass et Tag or proper ty identification number assi gned by the company to this workstation. ● Enable power-on password pr ompts during system restarts (warm-starts) and power on. ● Hide or show the integrated I/O functionality, in cluding serial, USB, or parallel ports, aud io, or embedded NIC. Hidden devices are inacce ssible, [...]

Computer Setup (F10) Utility menu The following tables describe the functions availa ble in Computer Setup (F10) (BIOS) utility menu. NOTE: With new BIOS releases, the fo llowing content is subject to change, so the menu mig ht be different than shown. Table 2-1 Computer Setup (F10) Utility menu desc riptions for the HP Z220 SFF and Z220 CMT Workst[...]

Table 2-1 Computer Setup (F10) Utility menu desc riptions for the HP Z220 SFF and Z220 CMT Workstations (co ntinued) Heading Option Description Apply Defaults and Exit Restores the de fault settings defin ed in Default Setup. Ignore Changes and Exit Exits computer setup without applying or saving changes. Save Changes and Exit Saves changes to syst[...]

Table 2-1 Computer Setup (F10) Utility menu desc riptions for the HP Z220 SFF and Z220 CMT Workstations (co ntinued) Heading Option Description ◦ Hard Drive ◦ Network Controller You can take the following actions: ● Press Enter to drag a device with the arro w keys to a preferred place, then press Enter again to drop the device in place. ● [...]

Table 2-1 Computer Setup (F10) Utility menu desc riptions for the HP Z220 SFF and Z220 CMT Workstations (co ntinued) Heading Option Description Device Security Makes the following devices available or hidden to the computer: ● Embedded Security Device (hidden by default) ● System Audio ● Network Controller ● SATA ports With the exception of[...]

Table 2-1 Computer Setup (F10) Utility menu desc riptions for the HP Z220 SFF and Z220 CMT Workstations (co ntinued) Heading Option Description System Security With the exception of the first option, Data Execu tion Prevention, changing any of these system s ecurity settings and choosing Fi le > Save Changes and Exit will result in the computer [...]

Table 2-1 Computer Setup (F10) Utility menu desc riptions for the HP Z220 SFF and Z220 CMT Workstations (co ntinued) Heading Option Description Secure Boot Configuration ● Legacy Support—Enable/Disable ● Secure Boot—Enable/Disable All option ROMs mu st support EFI. ● Key Management ◦ Clear Secure Boot Keys—Clear/Don't Clear ◦ K[...]

Table 2-1 Computer Setup (F10) Utility menu desc riptions for the HP Z220 SFF and Z220 CMT Workstations (co ntinued) Heading Option Description NOTE: If you turn off power to the computer using a power strip, you cannot use the suspend/ sleep feature or the Remote Management features. ● POST Delay (None (default), 5 , 10, 15, 20 seconds)—Delays[...]

Table 2-1 Computer Setup (F10) Utility menu desc riptions for the HP Z220 SFF and Z220 CMT Workstations (co ntinued) Heading Option Description Device Options Enable/disable the following device options: ● S5 Wake-on-LAN (Enabled/Disabled) ● Printer Mode (EPP+ECP, Output Only, Bi-Directional) ● Num Lock State at Power-On (On/Off) ● Integrat[...]

Table 2-2 Computer Setup (F10) Utility menu descri ptions for the HP Z420, Z620, and the Z820 Workstation s Heading Option Description File Sy stem Information Displays the following syst em characteristics: ● Product Name ● Memory Size ● SKU Number ● Integrated MAC 1 ● Integrated MAC 2 ● System BIOS ● Boot Block Date ● Chassis seri[...]

Table 2-2 Computer Setup (F10) Utility menu descri ptions for the HP Z420, Z620, and the Z820 Workstations (co ntinued) Heading Option Description Save Changes and Exit Saves changes to system configuration and exits the workstation setup. Storage Device Configuration Lists installed non-SCSI st orage devices (exc ept SATA devices) an d provides op[...]

Table 2-2 Computer Setup (F10) Utility menu descri ptions for the HP Z420, Z620, and the Z820 Workstations (co ntinued) Heading Option Description ◦ Hard Drive ◦ Network Controller Press Enter to drag a device to a preferred place. Press F5 to remove the device from consideration as a bootable device. Press F10 t o accept. MS-DOS drive letterin[...]

Table 2-2 Computer Setup (F10) Utility menu descri ptions for the HP Z420, Z620, and the Z820 Workstations (co ntinued) Heading Option Description Device Security Makes the following devices available or hidden to the workstation: ● Embedded Security Device ● SAS Controller ● SCU Controller ● USB3 Controller ● Intel High Definition (HD) A[...]

Table 2-2 Computer Setup (F10) Utility menu descri ptions for the HP Z420, Z620, and the Z820 Workstations (co ntinued) Heading Option Description System Sec urity Provides these options: ● Data Execution Prevention—E nables or disables Data Execution Prevention mode in the CPUs. This mode prohibits code from running in pages that were set up a[...]

Table 2-2 Computer Setup (F10) Utility menu descri ptions for the HP Z420, Z620, and the Z820 Workstations (co ntinued) Heading Option Description CAUTION: Choos ing Reset to Factory Settings may result in significant data loss. The embedded security device is a critic al component of many security schemes. Erasing the secur ity keys prevent access[...]

Table 2-2 Computer Setup (F10) Utility menu descri ptions for the HP Z420, Z620, and the Z820 Workstations (co ntinued) Heading Option Description Advanced 2 Power-On Options Enables you to set the following: ● POST Messages—Enables or disables the splash screen du ring POST. ● Press the ESC key for Startup Menu. ● Option ROM 1 prompt (Enab[...]

Table 2-2 Computer Setup (F10) Utility menu descri ptions for the HP Z420, Z620, and the Z820 Workstations (co ntinued) Heading Option Description Device Options Enables yo u to set the following device options: ● Num Lock State at Power-On (On or Off) ● S5 Wake-on-LAN (Enable or Disable) ● Internal speaker—(Enable or Disable) ● NIC Optio[...]

Desktop management This section summarizes cap abilities, features, and key components of computer management. Topics Initial computer config uration and deployment on page 61 Installing a remote system on page 61 Copying a setup configuration to another computer on page 62 Updating and managing software on page 63 HP Client Management So lutions o[...]

Initial computer configuration and deployment The computer includes a preinstalled s ystem software image. After a b rief soft ware unbundling process, the computer is ready to use. If you prefer to replace the preins talled software image with a custo mized set of system and applicatio n software, you can de ploy a customiz ed software image by: ?[...]

Copying a setup configurat ion to another computer This section provides information abo ut replicating the computer setup. CAUTION: Setup configuration is model-specific. File sy stem corruption can result if source and target computers are not the same model. To copy a setup c onfiguration: 1. Select a setup c onfiguration to co py, and then rest[...]

Updating and managing software HP provides several tools for manag ing and updating software on desktops and computers: ● HP Client Manager Software ● Altiris Client Mana gement Solutions ● HP SoftPaq Download Manager ● System Software Mana ger HP Client Management Solutions HP Client Management Solutions (C MS), available for downloa d fro[...]

HP SoftPaq Download Manager HP SoftPaq Download Manager is a free, easy-to-use interface for lo cating and downloading software updates for the HP client PC models in your environment. By specifyi ng your models, operating system, and language, you can q uickly locate, sort, and sele ct the softpaqs you need. For more information, go to http://www.[...]

If the syste m ROM fails the valid ation check, the Fa ilSafe Boot Block provides enough support to start the computer from a BIOS ima ge CD creat ed from a SoftPa q. The BIOS image CD programs the sys tem ROM with a valid image. When Boot Block detects an invalid system ROM, the computer power LED blinks red eight times and the computer beeps eigh[...]

Asset tracking Asset track ing features provid e asset tracking data that can be managed using HP S ystems Insight Manager (HP SIM), HP Console Management Controller (CMC), or other syste ms-management applications. Seamless, automatic integr ation between asset tracki ng features and these products enables you to choose the management tool that is[...]

SATA hard d isk drive security HP computers include the HP DriveLock facility for SATA hard disk drives to prevent unauthorized access to data. WARNING! Enabling DriveLock can render a SATA hard disk drive p ermanently inaccessible if the master password is lost or forgotten. No method exists to recover the passwo rd or access the data. DriveLock h[...]

DriveLock applications The most practical use of DriveLoc k is in a corporate environment. The system adm inistrator would be responsible for configuring the hard disk dri ve, wh ich involves setting the DriveLock master password and a temporary user p assword. If you forget the us er pas sword or if the equipment is pass ed on to another employee,[...]

Enabling DriveLock To enable and set th e DriveLock user password: 1. Power on or rest art the computer . 2. As soon as the compu ter is powered on, repea tedly press t he F10 key until you enter Computer Setup (F10) Utility. If you do no t press F10 at the appr opriate time , you must restar t the compute r, then repe atedly press F10 again to acc[...]

Password security The power-on passwo rd prevents unauthorized use of the co mputer by requiring entry of a password to access applications or data when the comp uter is powered on or r estarted. Th e setup passwo rd specifically prevents unau thorized acce ss to Computer Setup (F10) Utility and can also be used as an override to the power-on passw[...]

Establishing a power-on password using computer setup Establishing a power-on password through Comput er Setup (F10) Utility pr events access to the computer when power is connec ted, unless you s p ecify the password. When a power-on password is set, Computer Setup (F10) Utili ty presents Password Options in the Security menu. The password options[...]

Entering a setup password If a setup password has been established on the comp uter, you will b e prompted to enter it each time you run Computer Setup (F10) Utility. To enter a setup password: 1. Restart the computer. 2. As soon as the compu ter is powered on, press a nd hold F10 until you enter Co mputer Setup (F10) Utility. Press Enter to bypa s[...]

Deleting a power-on or setup password To delete a power-on or setup password: 1. Power on or rest art the computer . 2. Choose from the following: ● To delete the power-on password, go to step 4. ● To delete the setup pa ssword, as soo n as the computer is powered on, press and hold F10 until you enter Computer Se tup (F10) Utility. Press Enter[...]

Clearing passwords If you forget the password, you cannot access the c omputer. For instructions about clearing passwords, see Configuring password security and r esetting CMOS on page 159 . Chassis security Smart Cover Se nsor (optio nal) The optional Smart Cover Sensor is a combination of hardware and software technology that aler ts you if the i[...]

Side access panel solenoid lock The side access panel solenoid lock (available only on specific wo rkstations) sec ures the side access panel to the chassis. The solenoid is controlled by a loca l or remote s ignal. To lock the solenoid, set a password for the solenoid lo ck in Compu ter Setup (F10) Utility. To unlock the solenoid, remove the solen[...]

Programmable power butt on (Windows only) With ACPI (Advanced Configuration and Power Interf ace) enabled, you can customize the behavior of the power button so that rather than powering do wn, the workstation enters sleep mode (low power state), or hibernate mod e (very low power state) . This lets you go to standby wit hout closing applications, [...]

3 Component replacement information and guidelines This chapter provides warnings, cautions, informat ion, and guidelines for removal and replacement procedures. It does not document the step-b y-step procedure s. IMPORTANT: Removal and replacement procedures are now availabl e in videos on the HP website. Go to the HP Customer Self Re pair Service[...]

Warnings and cautions WARNING! These symbols on any surface or area of the equipment indicate the following: Presence of a hot s urface or hot component. If th is surface is contacted, the potential for injury exists. To reduce the risk of injury from a hot component, let the surfac e cool before touching. Presence of an electrical shock hazard. To[...]

Service considerations Tools and soft ware requirements The tools necessary for computer co mponent removal and installation are : ● Torx T-15 driver ● Flat blade and cross-tip screwdrivers ● Diagnostics software Electrostatic discharge (ESD) information Generating static Different activities generate different amou nts of static electricity [...]

Persona l groundi ng methods and equipment Use the following items to h elp prevent ESD damage: ● Wrist straps — These are flexible straps with a ma ximu m of one megohm ± 10% resistance in the ground cords. To provide a proper ground, wear the strap against bare skin. The ground cord must be connected and fit snug ly int o the banana pl ug co[...]

Product recycling HP encourages customers to recycle used electronic hardware, HP or iginal print cartridges, and rechargeable batteries. For information about recycling HP components or pro ducts, see http://www.hp.com/ go/recycle . Component replacement guidelines This section provides information and guidelines fo r removal and replacement proce[...]

Cable management Proper routing o f the internal cables is critical to the operation of the workstation. Follow good cable management prac tices when remo ving and installing c omponents. ● Handle cables with care to avoid damage. ● Apply only the tension required to seat or unse at cables during insertion or removal from the connector. ● Whe[...]

CPU (processor) and CPU heatsink CAUTION: Observe the following cautions when removing or replacing the heatsink. — When removing the heatsink, loo sen all screws a li ttle at a time to ensure the CPU remains level. Do not fully loosen one screw, and then move on to the next. — After you remove the CPU heatsink from the chassis, use alcohol and[...]

Expansion slots This section identifies and describes computer expa nsion card slots, and presents card configuration information. Go to http://www.hp.com/ go/quickspecs to learn which graphics c ards are supported in the workstation, how much memory each graphics card includes, and gra phics ca rd power requirements. Card configuration restriction[...]

HP Z220 SFF Workstation slot identification an d description Maximum power used by all slots must not exceed total system power and is subject to configuration limitations. Figure 3-1 Identifying expansion card slots Table 3-1 PCI slots Slot Type Mechanical compatibil ity Electrical compatibility 1 PCIe2 x1 x1 x1 2 PCIe2 x16 (4) x16 x4 3P C I e 3 x[...]

HP Z220 SFF Workstation installa tion sequence recommendations Table 3-2 Slot Installa tion sequence Load order Card description Slot 1 Slot 2 Slot 3 Slot 4 1 PCIe graphic card Only 2 S econd PCIe graphic card Only 3 PCIe audio card 1st 2nd 4P C I e N I C c a r d 1 s t 2 n d 5 PCIe 1394a card 1st 2nd 6 PCIe Wireless card 1st 2n d 7 S econd serial p[...]

HP Z220 CMT Workstation slot id entification an d description Maximum power used by all slots must not exceed total system power and is subject to configuration limitations. Figure 3-2 Identifying expansion card slots Table 3-3 PCI slots Slot Type Mechanical compatibil ity Electrical compatibility 1P C I e 2 x 8 ( 4 ) x 8 x 4 2P C I e 3 x 1 6 x 1 6[...]

HP Z220 CMT Workstation installa tion sequence recommendations Table 3-4 Slot installation sequence Load order Card description Slo t 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 Slot 7 1 PCIe graphic card Only 2 Second PCIe graphic card Only 3 PCIe NIC card 1st 3rd 2nd 4 PCIe 1394 card 1st 2nd 3rd 5 PCIe USB3.0 card 1st 2nd 6 PCIe audio card 1s t 2nd 3rd [...]

HP Z420 Workstation slot identification and description Maximum power used by all slots must not exceed total system power and is subject to configuration limitations. Figure 3-3 Identifying expansion card slots Table 3-5 PCI slots Slot Type Mechanical compatibil ity Electrical compatibility 1P C I e 2 x 4 ( 1 ) x 4 x 1 2 PCIe3 - x16 x16 x16 3P C I[...]

HP Z420 Workstation installati on sequence recommendations Table 3-6 Slot installation sequence Load order Card description Slo t 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 1 First PCIe graphic card Only 2 Second PCIe graphic card or Tesla C2075 Only 3 Third PCIe graphic card Only 4 Fourth PCIe graphic card Only 5 SAS card 2nd 1st 3rd 6 PCIe 1394b card 1[...]

HP Z620 Workstation slot identification and description Maximum power used by all slots must not exceed total system power and is subject to configuration limitations. Figure 3-4 Identifying expansion card slots NOTE: Slot 1 is not available in dual processor conf igurations. Table 3-7 PCI slots Slot Type Mech anical compatibility Electrical compa [...]

HP Z620 Workstation installati on sequence recommendations Table 3-8 Slot installation sequence Load order Card description Slot 1 Slot 2 Slot 3 Slot 4 Slot 5 Slot 6 1 Second System Board (Riser) Only 2 First PCIe graphic card Only 3 Second PCIe graphic card or High Performance GPU Compute card Only 4 PCIe 1394b card Only 5 Third PCIe graphics card[...]

HP Z820 Workstation slot identification and description Maximum power used by all slots must not exceed total system power and is subject to configuration limitations. Figure 3-5 Identifying expansion card slots Table 3-9 Expansion card slo t description and com patibility Slot Type Mechanical comp atibility Electrical compatibility 1 PCIe3 x8 (4) [...]

HP Z820 Workstation installati on sequence recommendations Table 3-10 Slot installation sequence Load order Card description Type Slot 0 Slot 1 Slot 2 * Slot 3 * Slot 4 Slot 5 Slot 6 Slot 7 1 1st high performance GPU Compute card PCIe- x16 2nd 1st 1 2 2nd high performance GPU Compute card (requires 2nd CPU and 1125w PSU) PCIe- x16 Only 3 1st PCI e [...]

Hard disk drives and optical disc drives Handling hard disk drives CAUTION: Take proper precautions wh en handling hard disk drives to prevent loss of work and damage to the comput er or drive. ● Do not remove hard drives from the shipping pa ckage for storage. Keep hard drives in their protective pac kaging unti l they are mounted in the compute[...]

Drive installation and cabling scenarios This section presents cabling guid elines for the most common maximu m storage configurations. If you add or remove drives, HP recommends you follow th ese guidelines for hig hest drive performance and efficient cable routing. HP Z220 SFF Workstations — SATA cable connection guidelines Configuration / PCA [...]

HP Z420 Workstations — Intel AHCI SATA controller guidelines See HP Z420 Workstation system board components on page 19 to determine the location of system board connectors. NOTE: Port 0 is the default port for the boot drive (t he default port c an be changed manually in the BIOS). System board connector Drive configuration s cenarios 1234 SATA [...]

HP Z420 Workstations — LSI 921 2-4i RAID controller guidelines See HP Z420 Workstation system board components on page 19 to determine the location of system board connectors. NOTE: Hard disk drives attached to RC J8 are designat ed b y the 9212-4i BIOS to be boot devices. If the hard disk drive c onnected to RC J8 is a memb er of a RAID array, t[...]

HP Z620 Workstations — Intel AHCI SATA controller guidelines See HP Z620 Workstation system board components on page 26 to determine the location of system board connectors. NOTE: Port 0 is the default port for the boot drive (t he default port c an be changed manually in the BIOS). System board connector Drive installation scenarios 123 SATA 0 S[...]

HP Z620 Workstations — LSI 921 2-4i RAID controller guidelines See HP Z620 Workstation system board components on page 26 to determine the location of system board connectors. NOTE: Hard disk drives attached to RC J8 are designat ed b y the 9212-4i BIOS to be boot devices. If the hard disk drive c onnected to RC J8 is a memb er of a RAID array, t[...]

HP Z820 Workstation cabling guideli nes See HP Z820 Workstation system board components on page 33 to determine the location of system board connectors. NOTE: Port 0 is the default port for the boot drive (t he default port c an be changed manually in the BIOS). System board connector Drive configuration s cenarios 1234 5 SATA RAID 5 only 6 SATA RA[...]

Memory Supported DIMM configurations NOTE: Mirroring and DIMM sparing are not supported. Table 3-12 Supported DIMM configurations Platform Configuration HP Z220 SFF ● Four DIMM slots ● Unbuffered ECC/nECC DIMMS only ● Maximum capacity: 32 GB HP Z220 CM T ● Four DIMM slots ● Unbuffered ECC/nECC DIMMS only ● Maximum capacity: 32 GB HP Z42[...]

BIOS errors and warnings The BIOS generates warnings/errors on invalid memory config urations: ● If the BIOS can find a valid memor y configuration by disabling plugged-in memory, it does so and reports a warning during POST. the workstation can still be started. The warning will indicate the location of th e failed DIM M on the system bo ard. ?[...]

HP Z220 SFF Workstation DIMM installation order Install DIMMs in this order. NOTE: If you install DIMMs of different sizes, load them in order of size, starting with largest and finishing with the smallest (larges t in DIMM 1, smalle st in last loaded DIMM ). Figure 3-6 DIMM installation order HP Z220 CMT Workstation DIMM installation order Install[...]

HP Z420 Workstation DIMM installation order Install DIMMs in this order. NOTE: If you install DIMMs of different sizes, load them in order of size, starting with largest and finishing with the smallest (larges t in DIMM 1, smalle st in last loaded DIMM ). Figure 3-8 DIMM installation order Component r eplacement gu idelines 105[...]

HP Z620 Workstation DIMM installation order Install DIMMs in this order. NOTE: If you install DIMMs of different sizes, load them in order of size, starting with largest and finishing with the smallest (larges t in DIMM 1, smalle st in last loaded DIMM ). Figure 3-9 Single processor DIMM installation order Figure 3-10 Dual processor DIMM installati[...]

HP Z820 Workstation DIMM installation order Install DIMMs in this order. NOTE: If you install DIMMs of different sizes, load them in order of size, starting with largest and finishing with the smallest (larges t in DIMM 1, smalle st in last loaded DIMM ). Figure 3-11 Single-processor DIMM installation order Figure 3-12 Dual-processor DIMM installat[...]

Power supply Power supply specifications All power supplies have these specifications: ● Wide-ranging , active P ower Factor Corr ection (PFC) ● ENERGY STAR® qualified (c onfiguration dependent) ● FEMP Standby Power compliant @1 15V (<2W in S5 – Power Off) ● Surge tolerant (withstands power surges up to 2000V) NOTE: HP Z820 Workstatio[...]

Table 3-13 Power supply speci fications (continued) Z220 SFF Z220 CMT Z4 20 Z620 Z820 Heat dissipation, maximum (configuration and software dependent) 646.6 btu/hr (163.0 kcal/ hr) 899.1 btu/hr (226.6 kcal/ hr) 2354 btu/hr (593.2 kcal/hr) 3139 btu/hr (791 kcal/hr) Max: 3335 btu/hr (840 kcal/hr) Max1: 3878 btu/hr (977 kcal/hr) Max2: 5002 btu/hr (126[...]

Power consumption an d heat dissipation Power consumption and heat dissipation specificat ions are available for multiple configurations. To review available specifications, see http://www.hp.com/ go/quickspecs . To reach ze ro power co nsumption, unp lug the workstat ion from the power outl et or use a power strip with an on/off switch. For additi[...]

System cabling HP Z220 SFF Workstation system c abling See HP Z220 SFF Workstation components on page 1 to determine the location of system board connectors. Cable To Cable designator on syst em board PSU cable PCA (Main power) P1 (White) PSU cable PCA (PWR COMM) P2 (White) SATA power cable PCA (CPU power) P3 (White) SATA power cable HDD/ODD P160 ([...]

HP Z220 CMT Workstation system cabling See HP Z220 CMT Workst ation system boar d component on page 12 to determine the location of system board connectors. Cable To Cable designator on syst em board PSU cable PCA (Main Po wer) P1 (White) PSU cable PCA (CPU Power) P3 (White) PSU cable F irst hard drive (Bay 6) P8 (Black) PSU cable S econd hard dr i[...]

HP Z420 Workstation system cabling See HP Z420 Workstation system board components on page 19 to determine the location of system board connectors. Cable To Cable designator on syst em board PSU cable PCA (Main PWR) P1 PSU cable PCA (PWR MEM) P2 PSU cable First hard drive (Bay 6) D1 PSU cable Second hard drive (Bay 5) D2 PSU cable Third hard drive [...]

HP Z620 Workstation system cabling See HP Z620 Workstation system board components on page 26 to determine the location of system board connectors. Cable To Cable/system board designator PSU cable PCA P1(PWR) P1 PSU cable PCA P2(PWRMEM) P2 PSU cable First hard drive HDD BAY 0 PSU cable Second hard drive HDD BAY 1 PSU cable Third hard drive HDD BAY [...]

HP Z820 Workstation system cabling See HP Z820 Workstation system board components on page 33 to determine the location of system board connectors. Cable To Cable/system board designator PSU cable (C1) PCA (P1) P1 PSU cable (C3) PCA (P2) P2 PSU cable (C3) PCA (P3) P3 PSU cable (C3) PCA (P4) P4 PSU cable (C2) Graphics card G1 PSU cable (C2) Graphics[...]

4 Diagnostics and troubleshooting This chapter describes the tools available for diagnosing and tro ubleshooting syst em issues. Topics Calling support on page 117 Locating ID labels on page 118 Locating warranty informatio n on page 119 Diagnosis guidelines on page 119 Troubleshooting checklist on page 121 HP troubleshooting resources and tools on[...]

Calling support At times you might encounter an issue that requires support. When you call support: ● Have the computer readily accessible. ● Write down the computer serial numbers, prod uct numbers, model names, and model numbers and have them in front of you. ● Note any applicable error mess ages. ● Note any add-on options. ● Note the o[...]

Locating ID labels To assist in troubleshooting, product, serial, and authentication numbers are a vailable on each computer. ● All workstations have a serial number (unique for each workstation) and product number. Have these numbers availa ble when you contact support. ● The Certificate of Authentication (COA) is us ed for systems with Window[...]

Locating warra nty information To locate base warranty information, see http://www.hp.com/ support/warranty-lookuptool . To locate an existing Care Pack, s ee http://www.hp.com/ go/lookuptool . To extend a st andard product war ranty, visit http://www.hp.com/ hps/ca repack . HP Care Pack Services offer upgraded service levels to extend and ex pand [...]

Diagnosis du ring operation ● Look for blinking LEDs on the side of the comput er. The blinking ligh ts are erro r codes that will help you diagnose the problem. Refer to the Diagnostic L ED and au dible (beep) codes on page 150 section of this document for information on inter preting diagnostic lights and audible co des. ● Check all cables fo[...]

Troubleshooting checklist Before running diagnostic utili ties, make sure that. ● The computer is c onnected to a work ing electric al outlet and powered on, and the power light is illuminated. ● The monitor (for tower or desktop configurations) is connected to a working electrical outl et and powered on, and the power light is illumin ated. ?[...]

HP troubleshooting resources and tools This section provides information on the HP Help and Suppo rt Center, Online support, an d Helpful Hints for troubleshooting. HP Support Assistant HP Support Assistant (Windows 7 systems only) helps you maintain workstation per formance and resolve pro blems. HPSA provides au tomated up dates, onboar d diagnos[...]

Troubleshooting a problem To help you troubleshoot pr oblems with your system, HP provides the Business Support Center (BSC). The BSC is a portal to an extensive selection of onli ne tools. To acce ss BSC and troub leshoot a pro blem with the workstation, complete the following: 1. Visit http://www.hp.com/ go/workstation support . 2. Under the Busi[...]

Helpful hints If you encounter a problem with the workstation, monitor, or softwar e, the following general suggestions might help you isolate and focus on the proble m before taking further action. At startup ● Verify that the workstation and monitor are plugged into a working electrical outlet. ● Remove all optical discs and USB drive keys fr[...]

● If the monitor connected to a tower, desktop or all- in-one computer is blank: ◦ Plug the monitor into a different video port on the computer if o ne is available. Alternatively, replace the moni tor with a monitor that you know is working properly. ◦ Verify that the computer and monitor are plugged into a working electrical outlet. ◦ Ver[...]

Troubleshooting scenarios and solutions This section presents troubleshooting scenarios an d possible so lutions for a Windows-base d system. Solving minor problems Table 4-1 Minor problems Problem Cause Possible Solution Workstation appears frozen and does not shut down when the power button is pressed. Software control of the power switch is not [...]

Table 4-1 Minor problems (continued) Problem Cause Possible Solution Workstation powered off automatically and the Power LED flashes red 2 times (once every second), followed by a 2-second pause, and then two simultaneous beeps so unded. Processor thermal protection is activated. A fan might be blocked or not turning. OR The processor heatsink is n[...]

Solving hard drive problems Table 4-2 Hard drive problems Problem Cause Solution Hard drive error Hard disk has bad sectors or has failed. Locate and block the usage of bad sectors. If necessary, reformat the hard disk. If the drive is detected by the BIOS, run DPS Self-test. Disk transaction problem The directory structure is bad, or there is a pr[...]

Table 4-2 Hard drive probl ems (continued ) Problem Cause Solution Non-system disk or NTLDR missing message System is trying to s tart from nonbootable media. Remove the optical disc or USB drive. System is trying to start from a damaged hard drive. 1. Insert a bootable system optical disc or USB drive and restart the computer. 2. If the hard drive[...]

Solving display problems These suggestions apply to monitors connected to desktop and tower configurations, and to external monitors connected to a ll-in-one configuratio ns. Table 4-3 Display problems Problem Cause Solution Blank screen (no video). The cable connections are not correct. Verify the cable connections from the monitor to the computer[...]

Table 4-3 Display problems (continue d) Problem Cause Solution Power LED flashes red 6 times (once every second), foll owed by a two-second pause, and then the computer beeps 6 times. Pre-video graphics error. For systems with a graphics card: 1. Reseat the graphics card. 2. If the card requires extern al power, make sure the power cable is properl[...]

Table 4-3 Display problems (continue d) Problem Cause Solution Fuzzy focus; streaking, ghost ing, or shadowing effects; horizontal scrolling lines; faint vertical bars; or unable to center the picture on the screen (flat-panel monitors using an analog VGA input connection only.) Flat-panel monitor’s internal digital conversion circuits might be u[...]

Table 4-4 Audio problems (continued) Problem Cause Solution Noise or no sound comes out of the speakers or headphones. 1. If you are using digital speakers that have a stereo jack and you want the system to autos witch to digital, use a stereo-to-mono adapter to engage the auto sense feature, or use multimedia device properties to switch the audio [...]

Solving power supply problems This section presents power su pply troubleshooting scenarios. Testing power supply Before replacing the power su pply unit (PSU), use the Built-I n Self-T est (BIST) feature to learn if the power supply still works. NOTE: Not all PSUs have the BIST functionality. Refer to the Rear panel components section of this docu[...]

Table 4-6 Power supply problems (continued) Problem Cause Solution If the system enters the POST, perform the fol lowing: a. Power off the workstation. b. Replace one device at a t ime and repeat this procedure until a failure occurs. c. Replace the device causing the failure d. Continue adding devices one at a time to verify that all devices are f[...]

Self-troubleshooting with HP Vision Diagnostics Hewlett-Packard Vision Diagnostics is a di agnostic tool that can be us ed by the end user or te chnical support personnel to view information about the hardware config uration of the computer and perform hardware troubleshooting on HP de sktop and wo rkstation systems. This diagnostic tool is used to[...]

results. The information in each ta b can be saved as an HTML file and stored on an optica l disc or USB flash drive. Use HP Vision Diagnostics to dete rmine if all the devices installed on the computer are recognized by the system and functioning pro perly. Running tests is optional but recommended after installing o r connecting a new device. Bef[...]

Creating and using a bootable USB key This section describes ho w to use a USB key to access th e HP Vision Diagn ostics. NOTE: Using a USB key is the most convenient method to access the HP Vision Diagnostics. It is faster than using a CD, and it accommoda tes both Memory and Vision diagnostics. The HP Memory Test is a comprehensive memory di agno[...]

User interface The HP Vision Diagnostics application prov ides six major functions, a ccessible through tabs: ● Survey — Current system hardware information ● Test — List of all diagnostics ava ilable for the system; tests are started here ● Status — Progress and status of cu rrently run ning diagnostics ● History — Past diagnostics[...]

Survey tab The Survey tab shows your system hardware information, organized into eleve n Categories (for example Processors ) and device instances (for example Processor 1 ). You can control the amount of information displayed by selecting a combination of View Level and Category . The View Levels include: ● Overview (default) — High-level su m[...]

Test tab The Test tab lists all availabl e diagnostics. The li sts have been tailored according to your system configuration. Individual test may be selected or deselected. Tests have three modes: ● Quick — Test runs quickly while covering all ha rdware. Test parameters cannot be modified. ● Complete — Includes all available tests and may t[...]

5. Click the Start Test button. The Status tab, which allows you to monitor the progress of the tests, automatically displa ys during the testing process. When the tests are complete, the Status tab shows whether th e devices passed or fai led. 6. If errors are found, go to the Er rors ta b to view detailed information and recommended actions. Stat[...]

Errors tab The Errors tab displays detailed information ab out any errors found, as well as any recommended actions. The Error Log displays the tests for devices that have failed during the diagnostic testin g and includes the following information: ● Device — Device tested ● Test — Type of test run ● Times Failed — Number of times the [...]

Saving and printing informatio n in HP Vision Diagnostics You can save the information displayed in the HP Vi sion Diagnostics Survey, History and Errors tabs to removable media. You cannot save to the hard driv e. The system automatica ll y creates an HTM L file that has the same appearance as the information displayed on the screen. 1. Insert rem[...]

Self-troubleshooting with HP PC Hardware Diagnostics HP PC Hardware Diagnostic s is a Unified Extensible Firmware In terface (UEFI) based diagnostic tool that can be used by the end user or technical su pport personnel to view in formation about the system configuration and to perform hard ware troubleshooting. The diag nostic tool runs outside of [...]

◦ Includes recommended actions with URL information on whom to contact ◦ Generatio n of the failu re co de indicates a definite hardware f ailure – no addition al troubleshooting is required ● Error Log — The tool automatically saves an error log on the device from which the test was run (either the hard drive or USB drive). This log is a[...]

Accessing HP PC Hardware Diagnostics The process to access the diagnostic s tool is the same regardless of the location from which it is run. The user pre sses ESC , while the system boots. This brings up the BIOS menu, which include an option to run diagnostics ( F2 ). Once selected, the BIOS searches fo r a diagnostic signature. The diagnostic to[...]

Running HP PC Hardware Diagnostics The System Information screen provides extensive system information, which is retrieved from the SMBIOS tables if they are available. Otherwise it is retrieved directly from the BIOS hardware. System information To display the system informati on, click System Information on the Main Menu. System information inclu[...]

Hardware diagnostic tests HP PC Hardware Diagnostics provides five sets of ha rd ware dia gnostic tests to validate the functionality of hardware components (including the CPU, memory, graphics, and system board) prior to booting the operating system. If the operating system cannot load because of a hardware failure, the di agnostics can be used to[...]

Diagnostic codes and errors This section presents information about diagnostic LED co des, LED color definit i ons, and PO ST error messages to help you tr oubleshoot problems. Diagnostic LED and audible (beep) codes This section describes the front panel LED error an d operation codes as we ll as the audible codes that might occur before or during[...]

Table 4-8 Diagnostic lights and audible codes (conti nued) Activity Possible cause Recommende d action Red Power LED blinks three times, once every secon d, foll owed b y a two-second pause. Three beeps. CPU not installed (not an indicator of bad CPU). 1. Verify t hat the CPU is present. 2. R eseat the CPU. Red Power LED blinks four times, once eve[...]

Table 4-8 Diagnostic lights and audible codes (conti nued) Activity Possible cause Recommende d action Red Power LED blinks eight times, once every secon d, foll owed b y a two-second pause. Eight beeps. Invalid ROM based on bad checksum. CAUTION: Internal componen ts migh t be powered even when the computer is off. To prevent dam age, disconnect t[...]

Table 4-8 Diagnostic lights and audible codes (conti nued) Activity Possible cause Recommende d action System does not power-on and LEDs are not blinking. No beeps. System unable to pow er on. CAUTION: Internal componen ts migh t be powered even when the computer is off. To prevent dam age, disconnect the computer power cord before you remove a c o[...]

LED color definitions The following table describes wh at each LED light on the computer fro nt panel signifies. Table 4-9 LED color definitions LED state LED color S ystem status Solid Blue System is on. Flashing Blue System is in Standby. Solid or flashing Red Sy stem ha s experienced an error. (See POST error messages on page 154 .) None No ligh[...]

Table 4-10 POST error messages (continued) Screen message Probable ca use Recommended action 162—System s Options E rror 1. R un Computer Setup (F10) utility and set default settings. 2. R eplace the CMOS battery. 3. R eplace the system board. 163—Time and Date Not Set ● Invalid time or date in configuratio n memory. ● RTC battery might nee[...]

Table 4-10 POST error messages (continued) Screen message Probable ca use Recommended action 304—Keyboard or System Unit Error Keyboard failure. 1. Reconnect the keyboa rd with the computer powered off. 2. Connect a keyboard directly to the computer (instead of through a switch box). 3. Be su re that none of the keys are pressed. 4. Replace keybo[...]

Table 4-10 POST error messages (continued) Screen message Probable ca use Recommended action 521—Memory fan (3) not detected Memory fan(3) missing, disconn ected, or defective. 1. R eseat the fan cable. 2. R eseat the fan. 3. R eplace the fan. 522—Memory fan (4) not detected Memory fan(4) missing, disconn ected, or defective. 1. R eseat the fan[...]

Table 4-10 POST error messages (continued) Screen message Probable ca use Recommended action 922—Front USB 2 Not Connected Front USB 2 mechanis m is missing or is not connected. 1. R eplace or reconnect the missing Fro nt USB 2 mechanism to the system board. 2. R eseat or replace the missing mech anism cable. 923—Fatal IRPP error. Potential sys[...]

5 Configuring password security and resetting CMOS This chapter describes how to configure passwor d secur ity and to reset CM OS. ● Preparing to configure passwords on page 159 ● Resetting the password jumper on page 160 ● Clearing and resetting the CMO S on page 161 Preparing to configure passwords Computer Setup (F10) Utility enab les you [...]

Resetting the password jumper Use the following procedure to disable the power-on or setup password feat ures and clear the power- on and se tup passwords. WARNING! To reduce the risk of personal in jury from electric al shock and ho t surface s, be sure to disconnect the power cord from the wall outlet and a llow the internal system co m ponents t[...]

Clearing and resetting the CMOS This section describes the ste ps necessary to successful ly clear and rese t the CMOS. The C MOS of the computer stores password inform ation and in formation about the computer configuration. Using the CMOS bu tton to reset CMOS To clear CMOS using the Clear CMOS button, use the following procedure: WARNING! To red[...]

Using Computer Setup (F10) Utility to reset CMOS 1. Access Computer Setup (F10) Utility menu. 2. When Computer Setup message appears in the lower- right corner of the screen, press F10 , and then press Enter to bypass the title screen, if nece ssary. If you do no t press F10 while the message is displayed, the computer must be rebooted to access th[...]

A Linux technical notes HP offers a variety of L inux solutions for HP wo rkstation customer s: ● HP certifies and supports Red Hat Enterp rise Linux (RHEL) on HP workstations. ● HP certifies SUSE Linux Enterprise Desktop (SLED) on HP workstations. ● HP offers a SLED 11 preload on some Z Series Workstations. For Linux setup a nd restore proce[...]

audio mixing. The performance of software audio mixing and p layba ck is greatly improved in ALSA version 1.0.13 and later. After the driver is installed, the o ptional NVID IA and AMD graphics cards that are supported in HP workstations also provide audio functionality over HDMI. The sign al can be passed thro ugh the DisplayPort connector to a mo[...]

NVIDIA Graphics Workstations Some workstation configurations come with NV ID IA Quadro graphics hardware. HP recommends the use of NVIDIA drivers for be st results on Linux sys tems. HP provides recommended versions of the drivers with RPM-compatible i nstallers for RHEL and SLED distributions. These are available from the HP In staller Kit for Lin[...]

AMD Graphics Workstations Some workstation configurations include AMD gr aphics hardware. HP recommends use o f AMD graphics drivers for best results on Linux syste ms. HP also provides recommended versions of AMD grap hics drivers with RPM-compatible instal lers for RHEL and SLED distributions. These are available fr om the HP Installer Kit for Li[...]

B Configuring RAID devices This appendix explains how to configu re RAID arrays on your workstation. Topics RAID hard drive maximum and associated storage controller options on page 167 Supported RAID configurations on page 168 Configuring Intel SATA RAID on page 169 Configuring RAID on an LSI 2308 or LSI 9212-4i controller on page 172 Configuring [...]

Supported RAID configurations All workstation platforms have Intel controllers, as follows: ● LSI 2308 controllers — HP Z820 Workstations ● LSI 9212-4i controll ers — HP Z420 and Z620 Workstations (optional) ● LSI 9260-8i co ntrollers — HP Z4 20, Z620, and Z820 Wo rkstations (optional) The following RAID configurations are supported: Ta[...]

Configuring Intel SATA RAID This section describes h ow to use Intel ® Rapid Storage Technology enterprise (Intel ® RSTe) or Intel ® Rapid Storage Technology (RST) t o se t up and manage SATA RAID volumes. NOTE: These instructions apply to Windows-based syst ems. They also apply to Linu x distributions that include the isci kernel driver support[...]

Configuring system BIOS To set up a RAID configuration, the emulation mode must be set to RAID+AHCI in Computer Setu p (F10) Utility. This is the default se tting. If the mode has been changed, follow thes e steps to reinstat e it. 1. During startup, press F10 to enter Computer Setup (F10) Util ity. Use the arrow keys to navigate and select options[...]

Configuring RAID with the Intel utility Follow these steps to create RA ID volumes. NOTE: The option ROM displays once for each controller. For example, if you have two drives on the AHCI controller and two o n the SCU controller, then both option ROMs display. Following the prompt, select Ctrl+I to choose the controller. 1. Press Ctrl+l when promp[...]

Configuring RAID on an LSI 2308 or LSI 9212-4i controller This section explains how to use the LSI Logic Configuration Util ity to set up a SATA or SAS RAID array on the LSI 2308 or LSI 9 212-4i controllers. NOTE: These instructions apply to both Window s-based systems and Linux-based syst ems. RAID 0 configuration Follow these steps to configure a[...]

RAID 1 configuration Follow these steps to configure an Integrated Mir ror ing (IM) volume with the BIOS-based configuration utility. The procedure assumes that the system has the required drives and drive controllers . 1. During BIOS startup, press Ctrl-C when promp ted to start t he LSI Logic Configuration Utility. Use the arrow keys and the spac[...]

RAID 1E/10 configuration Follow these steps to configure an Integrated Mir r oring Extended (IME) volume. The procedure assumes the system has the requ ired disk and disk controllers. NOTE: If an odd number of d rives is used, a RAID 1E array is created. If an even number of dr ives is used, a RAID 10 array is crea ted. 1. During BIOS startup, pres[...]

Configuring RAID on an LSI 9260-8i MegaRAID controller This section explains how to use the LSI Logic Configuration Ut ility to set up SATA or SAS RAID arrays on the LSI 9260-8 i MegaRAID controller. NOTE: These instructions apply to both Window s-based systems and Linux-ba sed systems. RAID 0 Follow these steps to configure a RAID 0 vo lume with t[...]

● Disable BGI: No , Yes ● Select Size: Specify the size of the RAID array 5. Select Next . 6. A message warns you of the effect of your particular Write Policy setting: ● Write Through :The configuration might result in slower performance. ● Always Write Back : The configuration results in optimal performance, but there is a risk of data lo[...]

Software RAID solution This section summar izes software RA ID considerations that are specific to the L inux env ironmen t, and provides links to addition al configuration resources. Software RAID considerations The Linux kernel softwa re RAID driver (called md , for multiple device ) offers integrated software RAID without the need for additional[...]

Configuring software RAID See the following sites for additional information about configuring software RAID on Red Hat Enterprise Linux (RHEL) or SUSE Linux Enterprise Desktop (SLED): ● Red Hat Ent erprise Linux 6—S ee the Storage Administratio n Guide at http://doc s.redhat.c om/ docs/en-US/Red_Hat_Enterprise_Linux/6/html /Storage_Administrat[...]

C System board designators HP Z220 SFF Workstation Designator Silk scr een Compon ent/Description E15 E15 Crisis recovery header/jumper E49 E49 Clear password header/jumper J9 RJ45/USB LAN/DUAL USB 2.0 J10 J10 Quad rear USB 3.0 J20 PCI1J20 PCI slot (white) J31 J31 X1PCIEXP1 PCIe2 x 1 slot (black) J41 J41 X16PCIEXP PCIe3 x 16 slot (black) J42 J42 X4[...]

Designator Silk scr een Compon ent/Description P151 MEDIA2 Media card reader P160 SATAPWR1 HDD power (black) XBT1 XBT1 BAT Battery holder XMM1 - XMM4 XMM1 - XMM4 DIMM1 - DIMM4 Memory slots XU1 XU1 CPU socket HP Z220 CMT Workstation Table C-1 HP Z220 CMT Workstation system board designators Designator Silk screen Compon ent E15 E15 Crisis recovery h[...]

Table C-1 HP Z220 CMT Workstation system board designator s (continued) Designator Silk screen Compon ent P6 SPK R Speak er P8 P8 CHFAN Rear system fan P9 P9 Front fan header P24 P24 FRONT USB Front panel USB header P25 P25 INTERNAL USB2 Dual internal USB header P26 P26 INTERNAL USB3 Single internal USB header P27 DASH/USB1 DASH/Dual internal USB P[...]

Table C-2 HP Z420 and Z 620 Workstatio n system board designators (continued) Designator Name on board Component E49/JP49 PSWD Clear Password header J9 RJ45/USB Stacked RJ45/Dual USB J10 USB Quad Stacked USB J20-22 PCIx (x=1-3) PCI slots J31-32 X1PCIEXPx (x=1-2) PCI Express X1 slot J41 X16PCIEX P or MXM PCI Express x16 or MXM graph ics slot J42 X4P[...]

Table C-2 HP Z420 and Z 620 Workstatio n system board designators (continued) Designator Name on board Component P9 CHFAN Front chassis fan header P10 FLOPPY Floppy header P11 CHFAN2 Rear chassis fan header (Z620) P23 FRONT AUD Header for Front Panel Audio P24/25 FRONT USB/FRONT USB2 Header for Front Panel USB P52 COMAB Header/Connector for 2nd Ser[...]

Table C-3 HP Z820 Workstation system board designators (continued) Designator Name on board Component J32 J32 SLOT5-PCIe2 x8(4) PCI Express Gen 2 x 8 (4) Slot, Open-Ended J33 J33 SLOT4-PCIe3 x16 PCI Ex press Gen 3 x16 Graphics Slot J34 J34 SLOT3-PCIe3 x16(8) PCI Expres s Gen 3 x16(8) Slot J41 J41 SLOT2-PCIe3 x16 PCI Ex press Gen 3 x16 Graphics Slot[...]

Table C-3 HP Z820 Workstation system board designators (continued) Designator Name on board Component P85 SAS5 SAS/SATA Port 5 P86 SAS6 SAS/SATA Port 6 P87 SAS7 SAS/SATA Port 7 P93 FRNT FAN2 Front Fan 2 Header P94 FRNT FAN1 Front Fan 1 Header P125 LC1 Liquid Cooling Header 1 P126 LC0 Liquid Cooling Header 0 SW3 SW3 Rear Power Button/LED SW50 CMOS C[...]

Index B BIOS ROM 41 C Cable management 82 CMOS 159 clearing and resetting 161 Computer Setup (F10) Utilit y 42 Menu description 44 Configuring RAID devices 167 maximum hard drives allowed 167 SAS RAID on LSI 2308 or LSI 9212-4i controll ers 172 SAS RAID on LSI 9260-8i MegaRAID controller 175 SATA RAID 169 D Desktop management 60 Altiris Client Mana[...]

HP Z620 Workstatio n chassis 25 HP Z620 Workstation front panel 23 HP Z620 Workstation rear panel 24 HP Z820 Workstation 30 HP Z820 Workstatio n chassis 32 HP Z820 Workstation front panel 30 HP Z820 Workstation rear panel 31 Workstation setup Ensuring proper ventilation 38 Index 187[...]