JVC LST0979-001B инструкция обслуживания

OUTDOOR DOME CAMERA TK-C2201WPU (For USA and Canada) TK-C2201WPE (For Europe) INSTRUCTIONS . For Customer Use: Enter below the Serial No. which is located on the body. Retain this information for future reference. Model No. TK-C2201WPU,TK-C2201WPE Serial No. LST0979-001B[...]

Contents Introduction Contents ............................................................................................................. 2 Features ............................................................................................................. 3 Operating Precautions ................................................................[...]

Thank you for purchasing this product. Before use, please read this "INSTRUCTIONS" and the information materials included to ensure proper use of this product. These instructions are for TK-C2201WPU/TK-C2201WPE. TK-C2201WPE is not evaluated by UL. Features v Easy DAY/NIGHT function (TK-C2201WPU) v DAY/NIGHT surveillance with auto IR cut f[...]

Operating Precautions m Storage and Location of Use v Do not install the camera in the following places. - In a place with vapor or oil, for example in a kitchen. - When the ambient temperature rises above or falls below the acceptable range (from -10 f to 50 f ) - In a place at which corrosive gases are emitted. - Near a source of radiation, X-ray[...]

m Disclaimer v We will not be responsible for any inconveniences or disturbances caused in the event of privacy invasion as a result of camera footages of this product. m Others v When using this camera with [AGC] set to "MID" or "HIGH", the sensitivity increases automatically for dark images and the screen may appear grainy, bu[...]

Name of Parts Camera . . A D E B C J K F H I G A Mounting Hole 2 2 ( A page 14) B Fall Prevention Wire Mounting Screw ( A page 14) C Conduit Plug/Hole (side) ( A page 21) D Dome Cover ( A page 13) E Inner Dome ( A page 13) F Video signal output connector (BNC) ( A page 10) ( A page 15) Introduction 6[...]

G Protection Cover ( A page 15) H Power Supply Cable ( A page 11) ( A page 15) I Hole for Connecting Cables, Conduit Hole ( A page 20) J Base ( A page 19) K Dome Cover Fastening Screw 2 3 ( A page 13) Introduction 7[...]

Name of Parts (Continued) Camera (Interior) The dome cover and inner dome are removed. . . D C H A B L 1 F ADJ MENU MONITOR SET MONITOR TYPE NOT USED DIPSW SEE INSTRUCTION MANUAL BLC OFF D/N AUTO CRT 1 2 3 4 OFF LCD ON F ADJ M N E G I F P Q R S O J K A Focus Adjustment Ring ( A page 25) B Zoom Adjustment Ring ( A page 25) C Rotation Knob ( A page 2[...]

F Space for Inserting Heater When mounting the heater (sold separately: KA-ZH215U), read the instruction manual of the heater before mounting. G Power Supply Connector for Heater For connecting to the power supply connector of the heater. H Tilt Fastening Screw 2 2 ( A page 24) I [MONITOR] Terminal (RCA pin) ( A page 23) J Lug Plate ( A page 16) K [...]

About Connection Cables The maximum connection distance varies with the type of cable used. v Be sure to turn off the power of devices before connecting cables. . . To Power Supply To video Signal Cable Memo v Connect to AC 24 V power supply if using the heater (sold separately: KA-ZH215U). Video signal cable (coaxial cable) Connect a 75 K coaxial [...]

DC 12 V or AC 24 V power supply cable Connect the power cord to the DC 12 V or the AC 24 V power supply. The unit is to be powered by a UL Listed Class 2 power supply only. (For USA and Canada) The AC 24 V and DC 12 V power supply shall conform to the following: UL Listed Class 2 power supply only, Class 2 not wet and Class 3 wet wiring (For USA) I[...]

Setting the Switches Before mounting the camera, set the function setting switches on the camera. To set the switches, use a fine-tipped screwdriver. . . D/N 1 2 3 4 AUTO BLC OFF ON MONIT OR TYP E CRT LCD - - NOT UESD OFF Function selection switches DIP Switch Settings Chart 1 [D/N AUTO/OFF] Day & Night Switch Set this to "AUTO" when [...]

Mounting the Camera Selecting a mounting method v Mount directly to the ceiling or on the wall ( A page 13) v Mounting the Camera Using the Conduit Hole at the Bottom of the Base ( A page 19) v Mounting the Camera Using the Conduit Hole at the Side of the Base ( A page 21) v Mounting the Camera using the Electrical Box ( A page 22) Memo When mounti[...]

Mounting the Camera (Continued) m Mounting the Camera Unit 1 Make a hole ( Φ 30 mm) in the ceiling using the template provided 2 Mount the fall prevention wire for connecting the camera unit to the ceiling The fall prevention wire is not provided. Prepare a wire, taking into due consideration the length, strength, pull and material (insulating). ?[...]

m Connecting the cable For safety reasons, turn on the power only after all the connection is complete. The status indicator lights up when the camera is turned on. 1 Connect the coaxial cable ( A page 10) Lower the protection cover and connect the connectors. Upon connecting, restore the protection cover to cover the connectors. This will isolate [...]

Mounting the Camera (Continued) m Process after connection Fill the conduit hole and mounting holes with sealing agent and insert the silica gel. 1 Fill the conduit hole and the screw mounted holes (2 locations) with sealing agent (GE silicon) Note Seal the holes completely. Failure to do so may cause water or moisture to enter, thereby fogging the[...]

m Adjusting images After mounting is completed, adjust the images while checking the actual image. ( A page 23) m Mounting the Dome Cover Attach the dome cover back when all settings are finished. 1 Mount the inner dome Mount the inner dome in a way that supports the tilt direction of the lens. Insert the inner depression of the inner dome into the[...]

Mounting the Camera (Continued) 2 Mount the dome cover ① Clean the dust and dirt on the dome cover. ② Align the position marks (3 locations) on the camera unit and dome cover, followed by pressing in directly to mount the cover. ③ Tighten the dome cover fastening screw. . . Position alignment mark (x 3) Dome cover Dome cover protective sheet [...]

Mounting the Camera Using the Conduit Hole at the Bottom of the Base Conduit hole: G3/4-14 UNC (TK-C2201WPU), M25 (TK-C2201WPE) 1 Remove the dome cover and inner dome ( A page 13) 2 Remove the camera unit from the base and mount the fall prevention wire to the camera unit ① Loosen the camera unit fastening screw (2 locations) with a screwdriver. [...]

Mounting the Camera (Continued) 3 Wind the sealing tape Wind the sealing tape around the pipe junction (where the conduit hole thread lines with the pipe screw hole) two or more times. 4 Mount the base to the pipe Turn and screw the base unit to the pipe in the clockwise direction. Note When screwing the pipe, do not screw beyond 12 mm. Doing so ca[...]

Mounting the Camera Using the Conduit Hole at the Side of the Base If the camera cannot be mounted directly to the ceiling, use the conduit hole at the side of the base to mount the camera to the pipe. Conduit hole: G3/4-14 UNC (TK-C2201WPU), M25 (TK-C2201WPE) 1 Remove the dome cover and inner dome ( A page 13) 2 Remove the camera unit from the bas[...]

Mounting the Camera (Continued) Mounting the Camera using the Electrical Box 1 Remove the dome cover and inner dome ( A page 13) 2 Mount the camera unit to the electrical box Mount the camera unit to the electrical box using the mounting hole (2 locations) with the M4 screw (2 pieces). Memo The screws are not provided. . . M4 Screw 4 Inch square el[...]

Adjusting Image After mounting the camera, adjust the images while looking at the actual image. Discharge the static electricity from your body by touching the metallic part of the monitor terminal before handling the camera as static electricity may cause the camera to malfunction. 1 Mount the monitor Connect the monitor terminal of this camera to[...]

Adjusting Image (Continued) 3 Adjust the shooting direction of the camera Adjust the camera for pan, tilt and rotation, and face the camera towards the subject. . MONITOR TYPE NOT USED DIPSW SEE INSTRUCTION MANUAL BLC OFF D/N AUTO CRT 1 2 3 4 OFF LCD ON 1 F ADJ MENU Tilt: 80 Rotation: 100 Pa n : 1 75 Tilt fastening scre w Shooting direction mark Pa[...]

4 Adjust the image size Loosen the fastening screw for the zoom adjustment ring and move the ring to the left/right to adjust the image size. After adjustment is complete, fasten the screw. 5 Adjust the focus ① Hold the focus adjust gear knob, shift the catch from point A to point B as illustrated in the diagram to disengage the gear. Note To pre[...]

Adjusting Image (Continued) 6 Fine adjust the focus ① Press and hold the [ J ] button. v Focus adjust mode will be activated and "FOCUS ADJUST MODE" is displayed on the monitor screen. v The contours are emphasized as the iris opens and the depth of field becomes shallow. v After adjustment, press [ K , H , I ]/[SET]/[MENU] to exit focu[...]

7 Tighten the fastening screw of the focus adjustment ring Hold and press the focus adjust gear between your fingers in the direction of the arrows in the diagram, and tighten the fastening screw of the focus adjustment ring. . . Foc us adjustment r ing Adjustment 27[...]

Adjusting the Auto White Balance Each light source has its own color temperature. Therefore, when the main light source lighting the subject is changed, adjust the white balance again. 1 Press the [MENU] button. 2 Select [WHITE BALANCE] with the [ J / K ] button and "AWC" with the [ H / I ] button, then press the [SET] button. 3 Zoom in t[...]

Specifications Horizontal resolution : 550TV lines (typical) Video S/N ratio : 52 dB (typical, AGC OFF) Minimum illumination : Color mode: 0.05 lx (typical, 50 %, F1.2, AGC HIGH) Black and White mode: 0.03 lx (TK-C2201WPU) (typical, 50 %, F1.2, AGC HIGH) 0.006 lx (TK-C2201WPE) (typical, 50 %, F1.2, AGC HIGH) Zoom ratio : 3.75 Focal length : 2.8 mm [...]

Specifications (Continued) Accessories : (TK-C2201WPU) WARRANTY CARD 2 1 INSTRUCTIONS 2 3 Silica gel 2 1 Wrench 2 1 Template 2 1 (TK-C2201WPE) INSTRUCTIONS 2 5 Silica gel 2 1 Wrench 2 1 Template 2 1 Others 30[...]

m External dimensions [Unit: mm (inch)] . . 121(4-3/4) 113(4-1/2) 160(6-1/4) 9 5(1/4) 42(1-5/8) 125(4-7/8) 160(6-1/4) SR53.7 (3/8) Screw f or conduit (bottom surface , side surface) (TK-C2201WPU: G3/4-14 UNC, T K -C2201WPE: M25) (2-1/8) * Specifications and appearance of this camera are subject to change for improvements without notice. Others 31[...]

TK-C2201WPU/ TK-C2201WPE OUTDOOR DOME CAMERA Q 2009 Victor Company of Japan, Limited LST0979-001B[...]