Makita 6990D инструкция обслуживания

INSTR UCTION MANU AL W ARNING: F or your personal saf ety , READ and UNDERST AND bef ore using. SA VE THESE INSTR UCTIONS FOR FUTURE REFERENCE. www .makitatools.com Cor dless Impact Driver Equipped with Electric Brake MODEL 6990D[...]

2 SPECIFICATIONS • Manuf acturer reser ves the right to change specifications without notice. • Specifications ma y differ from country to countr y . GENERAL SAFETY R ULES USA003-1 (FOR All BA TTER Y OPERA TED T OOLS ) W ARNING: Read and understand all instructions. F ailure to f ollow all instructions listed below , ma y result in electr ic sh[...]

3 Wo r k A r e a 1. Keep y our work area clean and well lit. Cluttered benches and dark areas invite acci- dents. 2. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Pow e r tools create sparks which may ignite the dust or fumes. 3. Keep bystander s, children, and visitors awa y whil[...]

4 18. Maintain tools with care. Keep cutting tools sharp and clean. Properly maintained tools with sharp cutting edge are less likely to bind and are easier to control. 19. Check f or misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tool’ s operation. If damaged, have the tool ser- viced befo[...]

5 SYMBOLS USD302-1 The f ollowings show the symbols used f or tool. V ....................... volts ................... direct current ................... no load speed .../min ................ rev olutions or reciprocation per minute ................ number of b low IMPOR T ANT SAFETY INSTR UCTIONS FOR CHARGER & B A TTER Y CAR TRIDGE USC001-3 [...]

6 11 . Do not disassemble charger or battery cartridge; take it to a qualified ser viceman when service or repair is required, Incor- rect reassembly ma y result in a risk of electric shock or fire. 12. T o reduce risk of electric shock, unplug charger fr om outlet before attempting any maintenance or cleaning. T urning off con- trols will not redu[...]

7 FUNCTIONAL DESCRIPTION CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed bef ore adjusting or checking function on the tool. Installing or removing battery cartridge • Alwa ys switch off the tool bef ore inser tion or remov al of the batter y cartr idge. • T o remove the battery car tr idge , [...]

8 NO TE: • The batter y charger is f or charging Makita batter y car tridge. Ne ver use it f or other pur poses or f or other manuf acturer ’ s batteries. • When you charge a ne w batter y car tridge or a batter y car tridge which has not been used for a long period of time, it ma y not accept a full charge. This is a normal condition and doe[...]

9 Switch action CA UTION: • Bef ore inser ting the batter y car tridge into the tool, alwa ys check to see that the s witch trigger actuates properly and retur ns to the “ OFF ” position when released. T o star t the tool, simply pull the switch trigger . T ool speed is increased by increasing pressure on the s witch trigger . Release the s w[...]

10 Installing or removing driver bit or soc ket bit Use only the driver bit or soc ket bit shown in the figure . Do not use any other driver bit or soc ket bit. T o install the bit, pull the sleev e in the direction of the arrow and inser t the bit into the slee ve as f ar as it will go . Then release the slee ve to secure the bit. T o remove the b[...]

11 OPERA TION The proper fa stening torque may diff er depending upon the kind or size of the scre w/bolt, the mater ial of the workpiece to be f astened, etc. The relation between fastening torque and f astening time is shown in the figures. Hold the tool firmly and place the point of the dr iv er bit in the screw head. Apply f orward pressure to [...]

12 4. The manner of holding the tool or the material of dr iving position to be f astened will affect the torque. 5. Operating the tool at low speed will cause a reduction in the fa stening torque. MAINTENANCE CA UTION: • Alwa ys be sure that the tool is switched off and the batter y cartr idge is remov ed before attempting to perf or m inspectio[...]

13 EN0001-1 Recyc ling the Battery The only wa y to dispose of a Makita batter y is to recycle it. The law prohibits an y other method of disposal. T o recycle the batter y: 1. Remov e the batter y from the tool. 2. a) T ak e the batter y to your nearest Makita F actor y Ser- vice Center or b) T ak e the batter y to your nearest Makita A uthorized [...]

Memo 14[...]

Memo 15[...]

Memo 16[...]

17 First-Class Postage Required Post Office will not deliver without proper postage. Makita U .S.A., Inc. 14930 Nor tham Street La Mirada, CA 90638-5753 Fold Cut[...]

18 1. This product was pur chased from: Home Center Hardware/Lumber Store T ool Distributor Industrial Supply Construction Supply Other ( ) 3. Ho w did you learn about this product: Magazine F rom Dealer Newspaper Store Display Catalog Radio Exhibition F rom Friend Previous Usage Other ( ) 2. Use of the pr oduct is intended for: Construction T rade[...]

19 F A CT OR Y SER VICE CENTERS 1-800-4-MAKIT A RET AIN THIS POR TION FOR Y OUR RECORDS ALABAMA 2365 Pelham P arkway Pelham, AL 35124 (205) 620-1791 ARIZONA 3707 E. Broadw ay Rd., Ste. 6 Phoenix, AZ 85040 (602) 437-2850 ARKANSAS Shackleford Shopping Center 240 South Shackleford Rd., Ste. C Little Rock, AR 72211 (501) 224-5733 CALIFORNIA 41850 Chris[...]

W ARNING Some dust created by po wer sanding, sawing, g r inding, drilling, and other construction activities contains chemicals known to the State of Calif or nia to cause cancer , bir th def ects or other reproductive harm. Some e xamples of these chemicals are: • lead from lead-based paints, • cr ystalline silica from bricks and cement and o[...]