Makita 9557NB инструкция обслуживания

1 ENGLISH (Original instructions) INSTRUCTION MANUAL DOUBLE INSULA T ION IMPORT ANT : Read Before Using. Angle Grinder 9556NB 9557NB 9558NB 005801[...]

2 ENGLISH (Orig inal instruct ions) SPECIFICA TIONS Model 9556NB 9557NB 955 8NB Depressed center wheel dia meter 100 mm 1 15 mm 125 mm S pindle thread M10 M14 M14 Rated speed (n) / No load s peed (n 0 ) 1 1,0 00min -1 11 , 0 0 0 m i n -1 11 , 0 0 0 m i n -1 Overall length 271 mm 271 mm 271 m m Net weight 1.9 kg 2.0 kg 2.1 kg Safety class /II • Du[...]

3 For Model 9557NB ENG102-3 Noise The typical A-weighted noise level determined a ccording to EN60745: Sound pressure level (L pA ) : 86 dB(A) Sound power level (L WA ) : 97 dB(A) Uncertainty (K) : 3 dB(A) Wear ear protection ENG208-5 Vibration The vibration tot al value (tri-axial v ector sum) determined according to EN60745: Work mode : surfac e [...]

4 GEA005-3 General Power T ool Safety W arnings W ARNING Read all safety w arnings and all instructions. Failure to follow the w arnings and instructions may result i n electric shock, fire and /or serious injury . Save all warnings and instructions for future reference. The term "power tool" in the w arnings refers to y our mains-operate[...]

5 22. Maintain power tools. Check for misalignment or binding of moving part s, breakage of part s and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools. 23. Keep cutting tools sharp and clean. Properly maintained cutting [...]

6 accessory into y our body . 14. Regularly clean the power tool’ s air vents. The motor’s fan will draw the dust in side the housing and excessive accumulation of pow dered metal may cause electric al hazards. 15. Do not operate the power tool near flammable materials. S parks could ignite these materials. 16. Do not use accessories that requi[...]

7 edge of the w orkpiece on both sides of the w heel. f) Use extra caution when making a “pocket cut” into existing wall s or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or object s that can cause kickba ck. Safety W ar nings Specific for Sanding Operations: a) Do not use excessively oversized sanding d[...]

8 FUNCTIONAL DESCRIPTION CAUTION : • Always be sure th at the tool i s switched of f and unplugged before adjusting o r checkin g function on the tool. Shaft lock 1 005802 CAUTION : • Never actuate the shaf t lock when the spindle is moving. The to ol may be damaged. Press the shaf t lock to prev ent spindle rot ation when installing or remov i[...]

9 Mount the wheel guard w ith the protrusion on the wheel guard band aligne d with the no tch on the bearin g box. Then rotate th e wheel guard to such an angle that it can protect the operator according to w ork. Be sure to tighten the screw securely . T o remove wheel guard, follow the installation procedure in reverse. Inst alling or remo ving d[...]

10 Operation with abrasi ve cut-off / diamond w heel (optional acces sory) 1 2 3 4 010855 The direction for mounting the lock nut a nd the inner flange varies by wheel thickness. Refer to the table b elow . Abrasive cut-off wheel Diamond wheel Thickness: Less than 4 mm (5/32") Thickness: 4 mm (5/32") or more 16 mm (5/8") 20 mm (13/16[...]

11 • Do not start the cutting operation in the workpiece. Let the wheel rea ch full speed and carefully enter into the cut moving the tool forward over the workpiece surface. The wheel may bind, walk up or kickback if the power tool is st arted in the workpiece. • During cutting operations, never chan ge the angle of the wheel. Placi ng side pr[...]

12 Makita Corporation Anjo, Aichi, Japan www.makita.com 884565G224[...]