Makita GA5020Y инструкция обслуживания

1 ENGLISH (Original instructions) INSTRUCTION MANUAL DOUBLE INSULA T ION W ARNING: For your personal safety , READ and UNDERST AND before using. SA VE THESE INSTRUCTIONS FOR FUTURE REFERENCE. Angle Grinder GA5020 GA5020C GA5021 GA5021C GA6020 GA6020C GA6021 GA6021C 008074[...]

2 ENGLISH SPECIFICA TIONS Model GA5020 GA5021 GA5020C / GA5021C GA6020 GA6021 GA6020C / GA6021C Depressed center whee l diameter 125 mm 125 mm 125 mm 150 mm 150 mm 150 mm S pindle thread M14 M14 M14 M14 M14 M14 No load speed (n o ) / Rated speed (n) 11 , 0 0 0 m in -1 11 , 0 0 0 m i n -1 10,000 min -1 10,000 min -1 10,0 00 min -1 9,000 min -1 Overa[...]

3 7. Do not abuse the cord. Never use the cord for carrying, pulling or unpl ugging the power tool. Keep cord away from heat, oil, sharp edges or moving part s. Damaged or ent angled cords increase the ri sk of electric shock. 8. When operating a power tool outdoors, use an extension cord suitable for out door use. Us e of a cord suitable for outdo[...]

4 and/or serious injur y . 2. Operations such as polishing are not recommended to be performed with this power tool. Operations for which the pow er tool was not designed may create a haza rd and cause personal injury . 3. Do not use accessories which are not specifically designed and recommended by the tool manufacturer . Just because the accessor[...]

5 forces, if proper precautions are taken. b) Never place your hand near the rotating accessory . Acce ssory may kickback over y our hand. c) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposi te to the wheel’s mov ement at the point of snagging. d) Use special ca[...]

6 20. Before using the tool on an actual workpiece, let it ru n for a while. W atch for v ibration or wobbling that could indicate poor installation or a poorly balanced wheel. 21. Use the specified surface of the wheel to perform the grinding. 22. Watch out fo r flying sparks. Hold the tool so that sparks fly away from y ou and other persons or fl[...]

7 For tool with lock-off button T o prevent the sw itch trigger from being a ccidentally pulled, a lock-of f button is prov ided. T o start the tool, depress the lock-o ff butto n and pull the switch trigger . Release the switch trigger to stop. For tool with typeB switch trigger 1 2 A B 008415 For tool with the lock-on switch T o start the tool, s[...]

8 Inst alling loop handle (Accessory) CAUTION : • Always be sure that the loop handle is in stalled securely before operation . 1 2 008049 Always install the loop handle on the tool be fore operation. Hold the tool's switch handle and the loop handle firmly with both hands during operation. Install the loop ha ndle so that its protrusion w i[...]

9 Inst alling or remo ving depressed center grinding w heel/Multi-disc (accessory) W ARNING: • Always use supplied guard w hen depressed center grinding wheel/Multi-disc is on tool. Wheel can shatter during use and gu ard helps to redu ce chances of personal injury . 1 2 3 007995 Mount the inner flange onto the spindle . Fit th e wheel/disc on th[...]

10 Replacing carbon br ushes 1 001 1 45 Remove and check the carbo n brushes regularly . Replace when they w ear down to the limit mark. Keep the carbon brushes clean and free to slip in the holders. Both carbon brush es should be repla ced at the same time. Use only identica l carbon brushe s. Use a screwdriver to remov e the brush holder caps. T [...]

11[...]

12 Makita Corporation 884710C5[...]