Onkyo TX-DS787 инструкция обслуживания

Contents Thank you for purchasing the Onkyo AV Receiver. Please read this manual thoroughly before making connections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver. Please retain this manual for future reference. TX-DS787 A ppendix [...]

2 1. Read Instructions – All the safety and operating instructions should be read before the appliance is operated. 2. Retain Instructions – The safety and operating instructions should be retained for future reference. 3. Heed Warnings – All warnings on the appliance and in the operating instructions should be adhered to. 4. Follow Instructi[...]

3 1. Warranty Claim You can find the serial number on the rear panel of this unit. In case of warranty claim, please report this number. 2. Recording Copyright Recording of copyrighted material for other than personal use is illegal without permission of the copyright holder. 3. AC Fuse The fuse is located inside the chassis and is not user-service[...]

4 Contents Before using Important Safeguards ......................................... 2 Precautions ......................................................... 3 Contents .............................................................. 4 Supplied accessories ......................................... 5 Features .........................................[...]

5 Contents Listening to RDS broadcasts .......................... 51 Listening to RDS broadcasts .......................................... 51 PTY program types in Europe ....................................... 51 Displaying Radio T ext (R T) ........................................... 52 Performing a PTY scan ......................................[...]

6 Features ■ THX Surround EX ® ■ THX ® Select Certified ■ Dolby ® Digital, DTS ® , Dolby ® Pro Logic TM ■ Theater-Dimensional TM Virtual Surround Mode ■ Cinema Re-EQ TM Circuitry ■ 100 W × 2 (Front), 100 W (Center), 100 W × 2 (Surround), 100 W (Surround Back) at 8 Ω , 20Hz-20kHz, 0.08% THD (FTC) ■ 135 W × 2 (Front), 135 W (C[...]

7 Installing the remote controller batteries 1. Remove the battery compartment cover by pressing and sliding the cover. 2. Insert two AA (R6 or UM-3) batteries into the battery compartment. Carefully follow the polarity diagram (positive (+) and negative (–) symbols) inside the battery compartment. 3. After batteries are installed and seated corr[...]

8 TUNING UP DOWN FM MUTE / MODE DISPLAY STEREO CHARACTER / MEMORY DIRECT THX SURROUND BASS / TREBLE EXIT MENU LISTENING MODE / DTS ZONE 2 VOL CH LEVEL FM AM PHONO C D TAPE DVD VIDEO 3 VIDEO 4 VIDEO 2 VCR 2 VIDEO 1 VCR 1 STANDBY/ ON POWER ANDBY ST ZONE 2 OFF ON REC OUT ZONE 2 PHONES AV RECEIVER TX-DS 787 MASTER VOLUME VIDEO AUDIO LR VIDEO CAM INPUT [...]

9 Front panel facilities PHONES jack This is a standard stereo jack for connecting stereo headphones. The audio for the front right and left speakers are sent to the headphone speakers. When the headphones are plugged in, the listening mode automatically changes to stereo and output to the speakers is stopped. AUDIO SELECTOR button This button is u[...]

10 Front panel facilities Front panel display SLEEP indicator PCM DIGITAL indicator Listening mode or digital input format indicator MEMORY indicator FM STEREO indicator Lights when tuned into an FM radio broadcast in stereo. TUNED indicator AUTO indicator Multi function display RDS indicator (European models only) FM MUTE/MODE button If you are li[...]

11 OPEN/CLOSE REC AUDIO MUTING DISC TRACK DVD CD PH TUN T2 T1 V1 STEREO 123 6 5 4 7 + 10 0 ENT 89 SURROUND THX DSP LEVEL + CH SEL Re-EQ LEVEL — DIMMER HOME THEATER CONTROLLER RC-390M LATE NIGHT DIRECT DS P V2 V3 V — L K J I H G F E D C B A 9 0 1 E M 2 3 4 5 6 7 8 Remote contr oller For a more detailed explanation of how to use the remote contro[...]

12 R R R L L L P B P R Y P B P R Y P B P R Y COMPONENT VIDEO REMOTE CONTROL PRE OUT R L ( SB ) ANTENNA VIDEO 1 V IDEO 2 DVD MON ITOR OUT V IDEO 3 R L INPUT 1 INPUT 2 OUTPUT VIDEO S VIDEO GND DIGITAL OUTPUT ( OPTICAL ) DIGITAL INPUT ( OPTICAL ) DIGITAL INPUT ( COAXIAL ) 1 2 1 2 FRONT SURR SURR BACK SUB WOOFER MUL TI CHANNEL INPUT FRONT SURR SURR BAC[...]

13 Rear panel facilities Optical digital input terminal An optical digital input terminal is equipped with a protection cap. When connecting, remove this cap. When not using, put the cap back on the terminal. COAXIAL Coaxial cable OPTICAL Optical fiber cable DIGITAL INPUT/OUTPUT (coaxial and optical) These are the digital audio inputs and outputs. [...]

14 Rear panel facilities MULTI CHANNEL INPUT By connecting a DVD player, MPEG decoder, or other component that has a multi channel port, you can playback the audio with 5.1 channel or 7.1 channel output. So, be sure to prepare a cable that can properly connect the TX-DS787 to the peripheral device. AUDIO IN/OUT These are the analog audio inputs and[...]

15 Rear panel facilities 12V TRIGGER terminal This terminal is provided so that you can use the operation of the TX-DS787 control the operation of another externally connected device. Connect the component to this 1/8-inch mini-jack terminal and when the set input source is selected, the device will turn on. Set the 12V TRIGGER terminal using the 1[...]

16 REMOTE CONTROL PRE OUT R L ( SB ) ANTENNA GND FRONT SURR SURR BACK SUB WOOFER MUL TI CHANNEL INPUT FRONT SURR SURR BACK SUB WOOFER CENTER ( SB ) CENTER R L AM FM 75 ZONE 2 MAIN IR IN DIGITAL OUTPUT ( OPTICAL ) DIGITAL INPUT ( OPTICAL ) DIGITAL INPUT ( COAXAL ) 1 2 1 2 OUT TAPE CD PH R L IN VIDEO 1 V IDEO 2 DVD MON ITOR OUT V IDEO 3 R L VIDEO S V[...]

17 MODE L AV RECEIVER TX-DS 787 MASTER VOLUME VIDEO AUDIO LR VIDEO CAM INPUT / 4 VIDEO S VIDEO Default setting Input source Digital input Component video CD OPTICAL 1 PHONO ---- FM AM TAPE ---- DVD COAXIAL 1 INPUT 1 VIDEO 1 COAXIAL 2 ---- VIDEO 2 ---- ---- VIDEO 3 OPTICAL 2 INPUT 2 VIDEO 4 ---- ---- Example of how to connect your equipment TV monit[...]

18 Example of how to connect your equipment Connecting your audio components Below is an example of how you can connect your audio components to the TX-DS787. Refer to the diagram on pages 16 and 17 for the following connection examples. 1. Connecting a turntable Using an RCA-type audio connection cable, connect the output terminal on the turntable[...]

19 9. Connecting video camera or television game Using an RCA-type video connection cable, connect the video output terminal (composite) on the device to the VIDEO 4 IN jacks on the TX-DS787. If there is an S video output terminal on the device, connect it to the S VIDEO 4 VIDEO CAM INPUT jack using an S video cable. 6. Connecting a satellite tuner[...]

20 Most dipoles have an arrow on them to indicate their orientation towards the screen. So for the side dipoles, the arrows point forward. For the back dipoles, the arrows should point towards each other to achieve the correct acoustical phasing in the room. Connecting speaker s 2 34 5 6 7 10 1 8 2 34 5 6 7 10 1 2 34 5 10 1 67 8 9 89 10 8 9 10 8 (O[...]

21 P B P R Y P B P R Y P B P R Y COMPONENT VIDEO REMOTE CONTROL ANTENNA VIDEO 1 V IDEO 2 DVD MON ITOR OUT V IDEO 3 R L INPUT 1 INPUT 2 OUTPUT VIDEO S VIDEO GND DIGITAL OUTPUT ( OPTICAL ) DIGITAL INPUT ( OPTICAL ) DIGITAL INPUT ( COAXAL ) 1 2 1 2 FRONT SURR SURR BACK SUB WOOFER MUL TI CHANNEL INPUT OUT TAPE CD PH R L VIDEO S VIDEO OUT OUT I N I N I [...]

22 REMOTE CONTROL PRE OUT R L R L DIGITAL OUTPUT ( OPTICAL ) DIGITAL INPUT ( OPTICAL ) 1 FRONT SURR VIDEO S VIDEO ZONE 2 MAIN IR IN ANTENNA AM FM 75 Strip away the insulation from the end of the cable, then fully insert the stripped end of the cable. (Indoor) AM loop antenna Connecting antennas Connecting the AM antenna cable 1. Press down the leve[...]

23 REMOTE CONTROL PRE OUT R L R L DIGITAL OUTPUT ( OPTICAL ) DIGITAL INPUT ( OPTICAL ) 1 FRONT SURR VIDEO S VIDEO ZONE 2 MAIN IR IN ANTENNA AM FM 75 REMOTE CONTROL PRE OUT R L R L DIGITAL OUTPUT ( OPTICAL ) DIGITAL INPUT ( OPTICAL ) 1 FRONT SURR VIDEO S VIDEO ZONE 2 MAIN IR IN ANTENNA AM FM 75 Connecting antennas Outdoor antenna (Indoor) AM loop an[...]

24 R R L L P B P R Y P B P R Y P B P R Y COMPONENT VIDEO ANTENNA VIDEO 1 V IDEO 2 DVD MON ITOR OUT V IDEO 3 R L INPUT 1 INPUT 2 OUTPUT VIDEO S VIDEO VIDEO S VIDEO OUT OUT I N I N I N I N R L FRONT SPEAKERS SURR SPEAKERS SURR BACK SPEAKER CE N SP E E R AV RECEIVER MODEL NO. TX-DS 787 AM FM 75 CAUTION: SPEAKER IMPEDANCE 6 OHMS MIN. PER EACH SPEAKER T[...]

25 Connecting to the IR IN MAIN input Outline If the TX-DS787 is located inside a cabinet or other enclosure where the infrared beams from the remote controller cannot enter, then operation with the remote controller will not be possible. In such a case, it will be necessary to install a remote sensor at a location outside of the cabinet for the in[...]

26 REMOTE CONTROL ANTENNA VIDEO 1 V IDEO 2 R L GND DIGITAL OUTPUT ( OPTICAL ) DIGITAL INPUT ( OPTICAL ) DIGITAL INPUT ( COAXAL ) 1 2 1 2 FRONT OUT VIDE O R L AM F 7 5 ZONE 2 M A IR IN PRE OUT R L ( SB ) FRONT SURR SURR BACK SUB WOOFER CENTER 8 7 6 5 4 3 2 1 Power amplifier Connecting po wer amplifier s and two surr ound bac k speakers Connecting po[...]

27 TUNING UP DOWN FM MUTE / MODE DISPLAY STEREO CHARACTER / MEMORY DIRECT THX SURROUND BASS / TREBLE EXIT MENU LISTENING MODE ZONE 2 VOL CH LEVEL FM AM PHONO C D TAPE DVD VIDEO 3 VIDEO 4 VIDEO 2 VCR 2 VIDEO 1 VCR 1 STANDBY/ ON POWER ANDBY ST ZONE 2 OFF ON REC OUT ZONE 2 PHONES AV RECEIVER TX-DS 787 MASTER VOLUME VIDEO AUDIO LR VIDEO CAM INPUT / 4 V[...]

28 5.OSD Setup 1.OSD Config 2.OSD Setup 3.OSD Position |ENTER| Quit:|OSD| 4.Preference 1.Volume Setup 2.Headphones Level 3.DTS LFE Level Setup |ENTER| Quit:|OSD| 3.Listening Mode Setup 6.Enhanced 7 Setup 7.Orchestra Setup 8.Unplugged Setup 9.Studio-Mix Setup 10.TV Logic Setup 12.All Ch Stereo Setup |ENTER| Quit:|OSD| 3.Listening Mode Setup 1.Stereo[...]

29 Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 1.Speaker Setup 1.Speaker Config 2.Speaker Distance 3.Level Calibration 4.Bass Peak Level |ENTER| Quit:|OSD| 1-1.Speaker Config a.Subwoofer :Yes b.Front :Small c.Center :Small d.Surr L/R :Small e.Surr Back :Small f.Surr Back Out :1ch Quit:|OSD| [...]

30 Speaker Setup 1. Speaker Setup menu After you have installed the TX-DS787, connected all the components, and determined the speaker layout, it is now time to perform the settings in the Speaker Setup menu for the optimum sound acoustics for your environment and speaker layout. Before you perform the following settings, it is important that you f[...]

31 Speaker Setup Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 1.Speaker Setup 1.Speaker Config 2.Speaker Distance 3.Level Calibration 4.Bass Peak Level |ENTER| Quit:|OSD| 1-2.Speaker Distance a.Unit :meters b.Front L/R : 3.60m c.Center : 3.60m d.Surr Right : 2.10m e.Surr Back R : 2.10m f.Surr[...]

32 Speaker Setup Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 1.Speaker Setup 1.Speaker Config 2.Speaker Distance 3.Level Calibration 4.Bass Peak Level |ENTER| Quit:|OSD| 1-3.Level Calibration a.Left : 0dB b.Center : 0dB c.Right : 0dB d.Surr Right : 0dB e.Surr Back R : 0dB f.Surr Back L : 0dB[...]

33 Speaker Setup Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 1.Speaker Setup 1.Speaker Config 2.Speaker Distance 3.Level Calibration 4.Bass Peak Level |ENTER| Quit:|OSD| 1-4.Bass Peak Level a.Bass Peak Level Limiter :Off Quit:|OSD| a. Bass Peak Level Limiter On: Select to set the bass peak l[...]

34 Input Setup Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 2.Input Setup Input:DVD 1.Audio Setup 2.Video Setup 3.Listening Mode Preset 4.Tone Control 5.IntelliVolume 6.12V Trigger |ENTER| Quit:|OSD| Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Qu[...]

35 Input Setup a. Digital Input This setting tells the TX-DS787 which input source button on the front panel is connected with which digital input jack on the rear panel. To perform this setting, you must first select a digital input source at the front panel and then set the name of the digital input jack it is connected to here. For example, if t[...]

36 Input Setup Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 2.Input Setup Input:DVD a.Audio Setup b.Video Setup c.Listening Mode Preset d.Tone Control e.IntelliVolume f.12V Trigger |ENTER| Quit:|OSD| 2-2.Video Setup Input:DVD a.Video :DVD b.Component Video :Input1 Quit:|OSD| a. Video This set[...]

37 Input Setup Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 2.Input Setup Input:DVD a.Audio Setup b.Video Setup c.Listening Mode Preset d.Tone Control e.IntelliVolume f.12V Trigger |ENTER| Quit:|OSD| 2-3.ListeningMode Preset Input:DVD a.2ch Source :Stereo b.PCM fs=96k :Stereo c.Multichannel,M[...]

38 Input Setup • THX Surround EX “ THX Surround EX - Dolby Digital Surround EX ” is a joint development of Dolby Laboratories and the THX division of Lucasfilm Ltd. In a movie theater, film soundtracks that have been encoded with Dolby Digital Surround EX technology are able to reproduce an extra channel which has been added during the mixing[...]

39 Input Setup T-D (Theater-Dimensional) For the best enjoyment of your home theater, it is recommended that you have at least front left and right speakers, a center speaker, and surround left and right speakers. However, even if you only have front left and right speakers, you can still enjoy multichannel audio by using this mode. This mode contr[...]

40 Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 2.Input Setup Input:DVD a.Audio Setup b.Video Setup c.Listening Mode Preset d.Tone Control e.IntelliVolume f.12V Trigger |ENTER| Quit:|OSD| 2-4.Tone Control Input:DVD a.Bass : 0dB b.Treble : 0dB Quit:|OSD| Input Setup 2-4. Tone Control sub-menu [...]

41 Listening Mode Setup Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 3.Listening Mode Setup 1.Stereo Setup 2.Theater-Dimensional Setup 3.Surround Setup 4.THX Setup 5.Mono Movie Setup |ENTER| Quit:|OSD| Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| [...]

42 Listening Mode Setup 3-6. Enhanced 7 Setup Select this to modify the Enhanced 7 listening mode. The parameters that can be set are shown in the table below. Parameter Setting Initial value a Subwoofer Off, On On b Re-EQ Off, On Off c Front Effect Off, On On d Effect Level Low, Mid-low, Middle, Middle Mid-high, High e Room Size Small, Mid-small, [...]

43 Listening Mode Setup Description listening mode parameters Subwoofer Set this to “ Off ” if you are not using a subwoofer (even if one is connected). If “ No ” is selected for the Subwoofer setting in the Speaker Config sub-menu, then this setting will not appear. Re-EQ Depending on the listening mode, you can either turn Re-EQ on or off[...]

44 Listening Mode Setup Center For systems that have a center speaker, the center channel signal can be output from the center speaker. For instance, in systems where the front left and right speakers are small, use of the center speaker may provide a better sound space. (If your system uses a center speaker, be sure to perform the level calibratio[...]

45 4-2. Headphones Level sub-menu You can use this sub-menu to adjust the volume output from the headphones so that it matches the level output from the speakers. The headphone volume can be adjusted between – 12 and +12 decibels. 4-3. DTS LFE Level Setup sub-menu This sub-menu is used to set the LFE level for the playback of DTS sources. Normal [...]

46 5. OSD Setup menu This menu provides settings for you to customize the on-screen display (OSD) for the TX-DS787 by setting different colors or positions for its display. OSD Setup Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 5.OSD Setup 1.OSD Config 2.OSD Setup 3.OSD Position |ENTER| Quit:[...]

47 Menu 1.Speaker Setup 2.Input Setup 3.Listening Mode Setup 4.Preference 5.OSD Setup |ENTER| Quit:|OSD| 5.OSD Setup 1.OSD Config 2.OSD Setup 3.OSD Position |ENTER| Quit:|OSD| 5-3.OSD Position Exit:|EXIT| Quit:|OSD| VIDEO 1 Hint: If this is set to “ Off, ” the background color will not be displayed even when there is no video signal input. d. D[...]

48 Enjo ying m usic in the remote zone Controlling the TX-DS787 from the remote zone 1. Aiming at the remote sensor, press the ON button on the remote controller. Note: Be aware that if you start using the system in the remote zone (Zone 2) while a recording is going on in the main zone, the recording will be stopped in the main zone. 2. Press the [...]

49 Listening to Radio Br oadcasts TUNED Tuned Band Frequency AUTO TUNED FM STEREO Tuned in stereo Band Frequency Auto mode Listening to FM/AM Radio Stations One of the features of the TX-DS787 that is most frequently used is its ability to play FM and AM broadcast radio stations. The TX- DS787 provides a number of listening modes perfect for listen[...]

50 Selecting a preset radio station 1. Press either the AM or FM input source button. The front display should show the currently selected frequency. If it displays the listening mode, press the DISPLAY button to display the frequency. 2. Turn the SSC dial and select the number of the desired preset station. When using the remote controller: 1. Mak[...]

51 Listening to RDS br oadcasts (European models onl y) Listening to RDS broadcasts RDS reception is available only on the European model and only in areas where RDS broadcasts are available. What is RDS? RDS stands for Radio Data System and is a type of FM broadcasting. RDS was developed within the European Broadcasting Union (EBU) and is availabl[...]

52 Listening to RDS broadcasts Displaying Radio Text (RT) If the station you are currently tuned into is broadcasting RT signals, they will be displayed in the front display on the TX- DS787. If the station does not, this function will be ignored. 1. To display the radio text, press the RT/PTY/TP button once. • If the current station you are list[...]

53 Enjo ying m usic or videos with the TX-DS787 Changing the listening mode To change the listening mode during playback, turn the SSC dial on the front panel or the listening mode buttons on the remote controller (see page 59). Listening with headphones To listen with headphones, plug a pair headphones with a standard stereo plug into the PHONES j[...]

54 Enjoying music or videos with the TX-DS787 If one of the messages shown below appears If you try to perform an operation that is not possible, “ Not available ” appears followed by one of the messages shown below to explain the reason. Enjoying the multichannel output Before you can use a component with multichannel output, you must first se[...]

55 Of course the TX-DS787 can also be used to record an input source media. This allows you to make copies of the music or videos you like, copy them from one type of media to another, or even record what is being broadcast on television or radio. Be aware that the Rec Out and Zone 2 buttons use the same circuit so that you cannot make recording an[...]

56 Recording a source To record an input source signal different from that you are currently watching or listening to This method outputs to the audio and video outputs the signal from the input source that you select here. This allows you to record an input source signal different from that which you are listening to or watching at the time of rec[...]

57 Giving a name to each input source You can program names for each input source (e.g., DVD, CD) and preset channel. Giving a name to eac h input sour ce and preset radio station To erase a name 1. Select the source whose name you wish to erase by pressing the corresponding input selector button. 2. Press the CHARACTER/MEMORY button twice. “ Nam[...]

58 Using remote contr oller Overview The RC-390M remote controller is a useful tool to help you operate the components of your home theater. To do so, first press the Mode button that corresponds to the device you wish to control. At this time, the display on the remote controller will change to show the component that is selected. Then simply pres[...]

59 Using remote controller LIGHT: Illuminates the buttons. SLEEP: Sets the sleep function. • The SLEEP buttons enables you to set the TX-DS787 to turn off automatically after a specified time period. If you press it once, the TX-DS787 will turn off after 90 minutes. Each time it is pressed thereafter, the remaining time until the TX-DS787 turns o[...]

60 Using remote controller Controlling an Onkyo CD player The z connector of the Onkyo compact disc player must be connected to the TX-DS787 (see page 13). 1. Press the CD MODE button. “ CD ” appears in the remote controller display. 2. Press the desired operation button. The buttons shaded in the figure to the left are the operation buttons th[...]

61 Using remote controller Controlling an Onkyo cassette tape deck The z connector of the Onkyo cassette tape deck must be connected to the TX-DS787 (see page 13). 1. Press the AUDIO/TAPE MODE button. “ AUDIO ” appears in the remote controller display. 2. Press the desired operation button. The buttons shaded in the figure to the left are the o[...]

62 Using remote controller Controlling an Onkyo DVD player Make sure that you point the remote controller toward the sensor on the Onkyo DVD player. 1. Press the DVD MODE button. “ DVD ” appears in the remote controller display. 2. Press the desired operation button. The buttons shaded in the figure to the left are the operation buttons that ca[...]

63 Pr ogramming the commands of remote contr oller s for other de vices into the remote contr oller 5 to 15 cm (2 to 6 inches) Buttons that cannot be programmed. P O W E R S LE E P D IM M E R S U R M O D E V ID EO -1 V ID EO -2 T A P E D VD C D C D D V D TU N E R TU N E R P H O N O IN P U T S EL E C T O R D IS C TA P E V O LU M E C H S E L P R E S [...]

64 Programming the commands of remote controllers for other devices into the remote controller 4. Press and hold down the button (that corresponds to the command you are programming) on the remote controller of the other device until the SEND/LEARN lamp on the remote controller flashes twice and “ SAVED ” appears in the display. After flashing [...]

65 Programming the commands of remote controllers for other devices into the remote controller OPEN/CLOSE REC AUDIO MUTING DISC TRACK DVD CD PH TUN T2 T1 V1 STEREO 123 6 5 4 7 + 10 0 ENT 89 SURROUND THX D SP LEVEL + CH SEL Re-EQ LEVEL – DIMMER HOME THEATER CONTROLLER RC-390M LATE NIGHT DIRECT DS P V2 V3 V – ENT OPEN/CLOSE REC AUDIO MUTING DISC [...]

66 Using a Macr o function Programming a Macro function You can program a different macro into the MODE MACRO button for each of the eight MODE buttons. The macro is then executed by pressing the appropriate MODE button and then pressing the MODE MACRO button. For example, to program the macro described above into the CD MODE button, perform the st[...]

67 Using a Macro function Programming the Direct Macro function With the direct macro function, you can program a series of button operations as a macro into the DIRECT MACRO button so the macro can be executed with just one touch. Note that for the direct macro function, only one macro can be programmed. For example, to program the macro described[...]

68 Using a Macro function Erasing a macro from the MODE MACRO button 1. Press and hold down the desired MODE button, press the MODE MACRO button, and then release both buttons. When you press the MODE button, the SEND/LEARN indicator lights and that mode appears in the display. When you press the MODE MACRO button, the indicator turns off. When you[...]

69 Using a Macro function Erasing all commands and macros that have been programmed This procedure will erase all the commands and macros that you have programmed into the remote controller and return it to its default settings. This operation will not affect the preset settings of the remote controller. 1. Open the battery cover and remove the bat[...]

70 T r oubleshooting guide If a problem occurs while you are using the remote controller, first try to operate the controls on the front panel of the TX-DS787 to make sure that it is not due to a malfunction (or worn out batteries) in the remote controller. POWER Power shuts off immediately after power on. • Amplifier protection circuitry has bee[...]

71 FM/AM TUNER AM stations cannot be received. • AM loop antenna is not connected. ➞ Connect the included AM loop antenna to the AM antenna terminals. Buzzing noise on AM stations (particularly noticeable at night or with weak stations). • Noise from electrical apparatus such as fluorescent lamp. ➞ Move the AM loop antenna to different posi[...]

72 For digital sources, sound is sometimes not output depending on media type. • Format of digital input source is fixed. Other digital formats will not be output. ➞ Set Digital Format to “ All ” in the Audio Setup sub-menu of the Input Setup menu (page 35). For DTS and PCM sources, noises or incorrect starts occur when the digital source i[...]

73 Specifications AMPLIFIER SECTION Continuous Average Power output (FTC) All channels: 100 W per channel min. RMS at 8 Ω , 2 channels driven from 20 Hz to 20 kHz with no more than 0.08% total harmonic distortion. 130 W min. RMS at 6 Ω , 2 channels driven from 1 kHz with no more than 0.1% total harmonic distortion. Continuous Power output (DIN)[...]

74 Memo[...]

75 Memo[...]

http://www.onky o.co.jp/ HOMEP AGE SN 29342963 D0008-1 Sales & Product Planning Div. : 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Tel: 072-831-8111 Fax: 072-833-5222 http://www.onkyo-intl.com ONKYO U.S.A. CORPORATION Park Way, Upper Saddle River, N.J. 07458 , U.S.A. Tel: 201- 785-2600 Fax: 201- 785-265 0 http://www.onkyousa.com ONKYO[...]