Sears PD6231 инструкция обслуживания

® 0W E AL 'S MODEL # SERIAL # PD/PH 4801 PD/PH 6801 PD/PH 623,1 PD/PH 4231 READ AND SAVE THESE [LEA Y CONSERVE ESTAS INSTALLATION INSTALACION MAINTENANCE MANTENIMtENTO |NSTRUCT[ONS |NSTRUCC|ONES D SAFETY SEGURIDAD D TROUBLE SHOOTING TRAZANDO FALLAS Ce_ratuladons: You have purchased a product of superior performance and design, which will give[...]

iNSTALLATiON • iN Typlo_l S_dO D|schsrge [nsta!lat[on demands con_ection of blower opening to existing air ducting system or to a dropper duct with a ceiiing diffuser. In either insta_ce, building modification is ne(ess[tated. The bottom discharge cooler is always moul_ted on the roof of the structure_ You will require a roof stand, roof jack, fl[...]

iNSTALLATION ° [NSTALAC[ON Water Connection i. Install float in hoie in the side of bottom pan opposite the pump. Seeparts illustration tO route the water line. Connect per above sketch. 2. Turn on the waterto the cooler and set float valve to maintain 21/_, inch water depth. The float valve is adjusted by bending the float valve rod, 3. B[eed-,of[...]

ELECTRICAL CONNECTIONS FIELD WiRiNG iNSTRUCTiONS 1. MAiN POWER SUPPLY THiS COOLER iS PREWIRED FOR 115 VOLT OR 230 VOLT, 6OHZ POWER ONLY. MAKE SURE YOU CONNECT YOUR COOLER TO THE CORRECT VOLTAGE. A_ B. Remove the control box cover- (4)screws. Remove 2"x 4" water tight junction box (3}, junction Box Cover (5), switch (4) and 1/2 _chase nipp[...]

Jl. THERMOSTAT CABLE |NSTALLATION |L INSTA_C[_N DEL CABLE DEL TERMOSTATO The thermostat for this cooler is connected to the cooler by means of a 6 conductor thermostat cable (not provided). Type CL2, 18 or 20 gauge, UL listed thermostat wire is recommended. A_ Route one end of the thermostat cable (9) through the 1/2 '_ hole in the corner post[...]

MAiN NANCE ° MANTEN[M[EN The cooler should be serviced at least once a year and more often if required. This includes cleaning,oiling, belt adjustment (if required) and pad repJacemenL Cleaning: I. Remove access doors and inlet air louvers. 2. Remove the overflow standpipe from the drain bushing and allow the reservoir to empty, 3. Use a hose with[...]

OPERATING iNSTRUCTiONS FOR THE PROi=STAT THERMOSTAT CONTROL SPECIAL FEATURES ®All information is saved during power failure or system shut-down and system returns to last operating mode when power is restored ®Programmable presets and 24 hour de}ay timer ®Programmed "soft" transition from high to !ow fan ®Automatic Pro Clean System ®[...]

SPECIAL FUNCTIONS KWIKSET Presets Press the KWIKSET button to display the DAY or NITE preset or to return to the standard display mode. Pressing the KWIKSET button to either the DAY or NITE preset causes the set point, FAN and COOL settings to assume the values stored in memory. Settings for set point, FAN, and COOL modes are displayed for each pre[...]

P CLEAN c NG O NC FULL AUTOMATIC: Fresh water for your evaporative coo]er every 5 hours of operation! How i! works.., The Pro Cleaning System (PCS) will automatically cycle every 5 hours of co®[er pump operation to empty the water reservoir within 1 _/!_ mhwtes. This cycle allows the cooler to re_ fiii with fresh water. At no time is cooling capab[...]

Troubleshooting Shourd a_ obvious probIem occur with your cooler consult the foiiowing table, ff you cannot correct the problem, contac_ a q_Ja[if_edsewice representative, PROBLEM Water Overflow Blower will not operate Fuse blown or circuit breaker tripped Dry Pads Cooler noisy Inadequate air flow PROBABLE CAUSE Float movement obstructed Float vatv[...]

Aerocool Pro Series Evaporative Coolers - Replacement Parts List Aerocool Pro Series Enfriador Evaporativo - Lista Reemplazo de Partes Replacement Part Parte de Reemptazo PD4801A PD4231A PH4801A PH4231A PD6801A PD6231A PH6801A PH6231A 1 Wet Section (Cabinet) 2 Water Distributor Assy. 3 Blower Assy - Complete 4 Motor Mount 5 Pump 6 Overflow Standpip[...]