Tiger Products Co., Ltd TS 100A инструкция обслуживания

P AR TS LISTING WITH MOUNTING AND OPERA TING INSTRUCTIONS SIDE ROT AR Y ASSEMBLIES Ford TS 100A CAB / WOC 06020004 Tiger Corporation 3301 N. Louise Ave. Sioux Falls, SD 57107 1-800-843-6849 1-605-336-7900 www .tiger-mowers.com Current as of 02/23/2010[...]

T O THE OWNER / OPERA T OR / DEALER All implements with moving parts are potentially hazardous. There is no substitute for a cautious, safe-minded operator who recognizes the potential hazards and follows reasonable safety practices. The manufacturer has designed this implement to be used with all its safety equipment properly attached to minimize [...]

FOR W ARD This manual contains information about many features of the T iger mowing and roadside maintenance equipment. Some of these include: Safety precautions, Assembly instructions, Operations, Maintenance and Parts. This manual will also assist you in the proper break-in, daily care, and troubleshooting of your new mower . We recommend that yo[...]

[...]

T ABLE OF CONTENTS SAFETY _____________________________________________ 1-1 Safety Information__________________________________ 1-2 ASSEMBL Y / MOUNTING SECTION _______________________ 2-1 OPERA TION SECTION _________________________________ 3-1 MAINTENANCE SECTION ______________________________ 4-1 P ARTS SECTION _________________________________[...]

[...]

SAFETY SECTION[...]

Side Rtry Safety Section 1-2 SAFETY SAFETY Indicates an imminently hazardous situation that, if not avoided, WILL result in DEA TH OR VER Y SERIOUS INJUR Y . Indicates an imminently hazardous situation that, if not avoided, COULD result in DEA TH OR SERIOUS INJUR Y . Indicates an imminently hazardous situation that, if not avoided, MA Y result in M[...]

Side Rtry Safety Section 1-3 SAFETY SAFETY ! Si no lee Ingles, pida ayuda a alguien que si lo lea para que le traduzca las medidas de seguridad. (SG-3) PELIGRO! LEA EL INSTRUCTIVO! DANGER! Never operate the Tractor or Implement until you have read and completely understand this Manual, the Tractor Operator’s Manual, and each of the Safety Message[...]

Side Rtry Safety Section 1-4 SAFETY SAFETY DANGER! Never allow children or other persons to ride on the Tractor or Implement. Falling off can result in serious injury or death. (SG-10) DANGER! Never allow children to operate or ride on the Tractor or Implement. (SG-11) WARNING! Do not mount the Tractor while the tractor is moving. Mount the Tractor[...]

Side Rtry Safety Section 1-5 SAFETY SAFETY WARNING! The operator and all support personnel should wear hard hats, safety shoes, safety glasses, and proper hearing protection at all times for protection from injury including injury from items thrown by the equipment. (SG-16) WARNING! T ransport only at safe speeds. Serious accident s and injuries ca[...]

Side Rtry Safety Section 1-6 SAFETY SAFETY WARNING! Periodically inspect all moving parts for wear and replace when necessary with authorized service parts. Look for loose fasteners, worn or broken parts, and leaky or loose fittings. Make sure all pins have cotter pins and washers. Serious injury may occur from not maintaining this machine in good [...]

Side Rtry Safety Section 1-7 SAFETY SAFETY CAUTION! On a fully-assembled unit, do not remove the Wing Retaining Strap until hoses are attached to the tractor and the Wing Cylinders are filled with oil. Lower the Wings slowly and carefully. Keep bystand- ers away during operations. (STI-5) DANGER! NEVER use drugs or alcohol immediately before or whi[...]

Side Rtry Safety Section 1-8 SAFETY SAFETY DANGER! The rotating parts of this machine have been designed and tested for rugged use. However, the blades could fail upon impact with heavy, solid objects such as metal guard rails and concrete structures. Such impact could cause the broken objects to be thrown outward at very high velocities. To reduce[...]

Side Rtry Safety Section 1-9 SAFETY SAFETY DANGER! Rotary Mowers are capable under adverse conditions of throwing objects for great distances (100 yards or more) and causing serious injury or death. Follow safety messages carefully. STOP MOWING IF PASSERSBY ARE WITHIN 100 YARDS UN- LESS: -Front and Rear Deflectors are installed and in good, working[...]

Side Rtry Safety Section 1-10 SAFETY SAFETY WARNING! Never leave the Tractor and Implement unattended while the Implement is in the lifted position. Accidental operation of lifting lever or a hydraulic failure may cause sudden drop of unit with injury or death by crushing. To properly park the implement when disconnecting it from the tractor, lower[...]

Side Rtry Safety Section 1-11 SAFETY SAFETY WARNING! The rotating parts of this machine continue to rotate even after the Tractor has been turned off. The operator should remain in his seat for 60 seconds after the brake has been set, the PTO disengaged, the tractor turned off, and all evidence of rotation has ceased. (SBM-5) “Wait a minute...Sav[...]

Side Rtry Safety Section 1-12 SAFETY SAFETY[...]

Side Rtry Safety Section 1-13 SAFETY SAFETY ITEM PART NO. QTY. DESCRIPTION 1 22839 1 INSTRUCT Don Not Lubricate With Automatic Grease Gun 2 22840 1 WARNING Foreign Objects Contacted 3 24028 1 WARNING Inspect Rear Flap 4 31522 1 LOGO TIGER MOWERS 5 31523 3 LOGO TIGER MOWERS 6 42350 1 DANGER Cuttershaft Direction 7 33743 1 INSTRUCT Mowing Safet Tips [...]

Side Rtry Safety Section 1-14 SAFETY SAFETY 10"X5.5" 31522 MOWER DECK 18.25"X10" 31523 HYDRAULIC T ANK 22840 INSIDE OF CAB 22839 MOWER DECK P AR T NO. LOCA TION 24028 MOWER DECK[...]

Side Rtry Safety Section 1-15 SAFETY SAFETY 5 42399 MOWER DECK 42400 MOWER DECK 33743 INSIDE OF CAB 42350 MOWER DECK P AR T NO. LOCA TION[...]

Side Rtry Safety Section 1-16 SAFETY SAFETY 29-6T3221 6T3220 FRONT PUMP MOUNT 6T3221 INSIDE OF CAB 6T3219 INSIDE OF CAB 6T3217 MOWER DECK P AR T NO. LOCA TION[...]

Side Rtry Safety Section 1-17 SAFETY SAFETY 6T3236 MOWER DECK 6T3243 INSIDE OF CAB 6T3234 INSIDE OF CAB 6T3233 INSIDE OF CAB P AR T NO. LOCA TION[...]

Side Rtry Safety Section 1-18 SAFETY SAFETY 16 6T3236 MOWER DECK HYDRAULIC T ANK 6T3243 INSIDE OF CAB 6T3234 INSIDE OF CAB 6T3233 HYDRAULIC T ANK P AR T NO. LOCA TION[...]

Side Rtry Safety Section 1-19 SAFETY SAFETY TB101 1 MOWER DECK 02962764 MOWER DECK DRAFT BEAM 6T3261 MOWER DECK 6T3249A MOWER DECK P ART NO. LOCA TION[...]

Side Rtry Safety Section 1-20 SAFETY SAFETY 02967827 CAB FENDER 02965262 DRAFT BEAM P AR T NO. LOCA TION[...]

Side Rtry Safety Section 1-21 SAFETY SAFETY 00756059 MOWER DECK 34852 HYDRAULIC T ANK[...]

Side Rtry Safety Section 1-22 SAFETY SAFETY ITEM PART NO. QTY. DESCRIPTION 50023 AVAIL MANUAL CANISTER COMPLETE 1 00776031 1 Round Manual Canister 33997 1 Decal, Sheet, Manual Canister 2 * Decal 3 * Decal 4 * Decal 5 * AVA IL Specification Product Manual 6 33753 1 EMI Safety Manual 7 34296 1 Front Adhesive Pad 8 34297 1 Rear Adhesive Pad 9 6T1823 4[...]

Side Rtry Safety Section 1-23 SAFETY SAFETY This section is intended to explain in broad terms the concept and effect of federal laws and regulations concerning employer and employee equipment operators. This section is not intended as a legal interpretation of the law and should not be considered as such. Employer-Employee Operator Regulations U.S[...]

Side Rtry Safety Section 1-24 SAFETY SAFETY[...]

ASSEMBL Y SECTION Assembly Section 2-1[...]

Assembly Section 2-2 ASSEMBL Y Before attempting to mount or service your Tiger mower , it is import ant to read and understand all of the information in the Safety section of this manual. Check complete shipment list against the packing list to make sure there are no shortages. Make certain the tractor model is the appropriate one for the mower re[...]

Assembly Section 2-3 ASSEMBL Y ADJUSTING REAR WHEELS Raise rear of tractor onto jack-stands. Follow the instructions in the tractor owners manual for adjusting tires and rims to 72” center for side mounted mowers and 79.8” for boom mowers. NOTE: This may require switching the wheels to opposite sides of tractor . CRANKSHAFT ADAPTER If necessary[...]

Assembly Section 2-4 ASSEMBL Y LIFT V A L VE MOUNT Install the valve mounting bracket to the inside of the right and left rear fender frame tube as shown below . Align the valve mounting plate with the drilled holes. Mark the center of one of the holes above and in line with the slotted holes in the valve plate. Do not use any holes that will be us[...]

Assembly Section 2-5 ASSEMBL Y WEA THER-P ACK/METRI-P ACK ASSEMBL Y These instructions apply to both Weather-Pack and Metri-pack connectors. NOTE: Use the specific tool for the type of connector you are assembling. 1. Apply seal to cable, before stripping insulation. 2. Align seal with cable insulation. 3. Put terminal in crimping tool, then positi[...]

Assembly Section 2-6 ASSEMBL Y POL Y -CARBONA TE SAFETY WINDOW NOTE: This should be done before mounting the main frame. 1. Disconnect gas shock at door . Remove the right side cab door from tractor cab by removing hinge pins. 2. Remove the existing hardware and discard factory glass door . 3. Place small beed of adhesive seal in the botom of the t[...]

Assembly Section 2-7 ASSEMBL Y MIRROR MOUNT 1. Remove the existing mirror bracket and mirror from the cab. 2 Remove the mirror and knob from existing bracket. 3. Install the supplied bracket using supplied hardware on the cab as shown below . 4. Install the mirror with the knob on the supplied bracket as shown below . Refer the parts section for de[...]

Assembly Section 2-8 ASSEMBL Y EXHAUST MOUNT NOTE: This should be done after mounting the main frame. 1. Cut the tractor hood as shown in pic. # 1 to accomodate modified exhaust turbo tube. 2 Remove the muffler from existing turbo tube. 3. Remove existing turbo tube from tractor turbo. 4. Install the exhaust mounting bracket and supporting brace. 5[...]

Assembly Section 2-9 ASSEMBL Y Picture # 4 Picture # 5[...]

Assembly Section 2-10 ASSEMBL Y SWITCH MOUNTING Refer to the parts section for wiring diagrams. Remove top instrument panel (tach, and hour meter) for access to the wires. Route the red and green wire from the switch box wires from the switch box to the bottom right corner of the instrumentm panel near window . Connect the red wire to the white wir[...]

Assembly Section 2-11 ASSEMBL Y TEMPERA TURE GAUGE MOUNTING (OPTIONAL) Mount the temperature gauge where it is clearly visible to the operator . Attach the green ( - ) wire from the negative post on the gauge to a grounded bolt on the tractor frame. Remove paint if needed to make a good ground. Remove the pipe plug from the side of the hydraulic re[...]

Assembly Section 2-12 ASSEMBL Y FRONT PUMP MOUNTING Install the pump mounting bracket on the front of the tractor with cap-screws and lock-washers as shown in the parts section illustration. DO NOT tighten fasteners at this time. Slide the pump drive shaft into the crankshaft adapter . The end with the shorter splines should be inserted into the ad[...]

Assembly Section 2-13 ASSEMBL Y INST ALLING O-RING FITTINGS Installing straight, 45 degree and 90 degree O-ring fittings requires that the O- ring, washer and nut (A) be up against the swivel body (B). Insert the swivel and turn in until the swivel is pointed in the right direction and the O-ring contact is made. Hold swivel in set direction with a[...]

Assembly Section 2-14 ASSEMBL Y CABLE LIFT DRAFT BEAM INST ALLA TION Install ½” O-ring breather into butt port of inboard cylinder . In all fittings in the rod end of the cylinder according to diagrams in parts section. These fittings should be positioned to face the butt end of the cylinder . Next turn the clevis onto the rod of the cylinder un[...]

Assembly Section 2-15 ASSEMBL Y DRAFT BEAM MOUNTING Pull the inboard cylinder piston rod down to the extreme extended position. Slide the draft beam under the cylinder , and align clevis hole with draft beam hole nearest to the tractor . Install pin and secure with R-clips. Using inboard cylinder as a pivot point, slide draft beam under tractor and[...]

Assembly Section 2-16 ASSEMBL Y TRA VEL LOCK MOUNTING Install the travel lock bracket with pin and clip on the draft beam. Slide the draft beam and align the travel lock bracket hole with the mounting hole on the main frame. Install the cap screw , lockwasher and hex nut as shown in the picture. Raise the deck/flail to it’s upright position (Deck[...]

Assembly Section 2-17 ASSEMBL Y DECK MOUNTING AND LIFT ASSEMBL Y Install the upper sheave bracket on the outboard cylinder and tighten securely against piston rod shoulder . T ighten the set screw , and align the draf t beam. Install the lower sheave bracket on the draft beam with a ¾” cap-screw and two hex nuts as shown in the diagram on the ne[...]

Assembly Section 2-18 ASSEMBL Y TURNBUCKLE ADJUSTMENT Extend the outboard cylinder until the deck touches the stop on the draft beam. Hold the deck in this position to adjust the lift cable tension. Adjust turn buckle until cable is tight. Lower and raise the deck to check adjustment. The mower deck should reach it’s stop on the draft beam at the[...]

Assembly Section 2-19 ASSEMBL Y DRAFT BEAM MOUNTING Pull the inboard cylinder piston rod down to the extreme extended position. Slide the draft beam under the cylinder , and align clevis hole with draft beam hole nearest to the tractor . Install pin and secure with R-clips. Using inboard cylinder as a pivot point, slide draft beam under tractor and[...]

Assembly Section 2-20 ASSEMBL Y DECK / MOTOR FEEDLINE Install the 1” hose with the 180 degree flange on the front side of the motor to the top of the solenoid valve. Secure to motor with flange kit, and install swivel fittings on the other end. Install the other 1” hose with the 60 degree flange on the back side of the motor to the bottom of th[...]

Assembly Section 2-21 ASSEMBL Y DECK / MOTOR FEEDLINE MOUNTING (cont.) Be sure that all grease zerks are installed in the draft beam pin bosses. Grease all areas of the draft beam according to the instructions in the maintenance section. Re-check all fittings for tightness and be sure teflon tape has been used at all connections. Fill hydraulic tan[...]

Assembly Section 2-22 ASSEMBL Y FINAL PREP ARA TION FOR OPERA TION Place operators safety and operation decals on the steering column and side counsel where they are clearly visible to the operator . These decals should be understood by each operator of the machine in conjunction with the safety and operation section of this book. The decals are to[...]

OPERA TION SECTION Operation Section 3-1[...]

Side Rtry Operation Section 3-2 OPERA TION Safety is of primary importance to the owner / operator and to the manufacturer . The first section of this manual includes a list of Safety Messages, that, if followed, will help protect the operator and bystanders from injury or death. Many of the messages will be repeated throughout the manual. The owne[...]

Side Rtry Operation Section 3-3 OPERA TION ST ARTING TRACT OR AND MOWER Check the operators manual received from the tractor manufacturer , for their recommendation and procedures pertaining to your particular make and model. When rotating parts are in motion, serious injury may occur if caution is not used or danger is not recognized. Never allow [...]

Side Rtry Operation Section 3-4 OPERA TION The rear mower height is controlled with the 3-point hitch control lever . Follow the instructions for this control is the tractor operators manual. The tilt of the rear mower is controlled with the third spool if the lift valve and is coordinated as shown above. The side and rear mower positions may optio[...]

Side Rtry Operation Section 3-5 OPERA TION When cutting tall shrubs or small trees (maximum recommended size of material to be cut is 2” diameter) begin each pass at the top of the material and work down with each consecutive pass. Use a low speed to allow the cutting blades time to mulch as well as cut the foliage. When the initial pass has been[...]

Side Rtry Operation Section 3-6 OPERA TION TRANSPORTING MOWER T ransporting under the units own power: When transporting between job sites or between cutting passes, the following procedure should be followed: Shut off the power to the cutting head(s) and allow all motion to come to a complete stop. Raise the draft beam to it’s highest position. [...]

Side Rtry Operation Section 3-7 OPERA TION Next, switch the hose ends and reconnect to form two separate closed loops, see diagram below . Disconnect the lift cable from the head and secure the loose end back onto the cable with the cable clevis. Remove the keeper bolt and draft beam outer pivot pin. Separate the mower head from the tractor . Now r[...]

Side Rtry Operation Section 3-8 OPERA TION INSPECTION SHEETS[...]

Side Rtry Operation Section 3-9 OPERA TION Rotary Mower PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is of f, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Mo[...]

Side Rtry Operation Section 3-10 OPERA TION TRACT OR PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Mower [...]

Side Rtry Operation Section 3-11 OPERA TION FRONT END LOADER PRE-OPERA TION Inspection Mower ID#_____________ Make___________________ Date:__________________ Shift____________________ Before conducting the inspection, make sur e the T ractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Load[...]

Side Rtry Operation Section 3-12 OPERA TION TRACT OR PRE-OPERA TION Inspection T ractor ID#____________ Make_____________________ Date:__________________ Shift______________________ Before conducting the inspection, make sur e the T ractor engine is off, all rotation has stop and the tractor is in the Park with the parking brake engaged. The Loader[...]

MAINTENANCE SECTION Maintenance Section 4-1[...]

Maintenance Section 4-2 MAINTENANCE T iger Mowers are designed for high performance and rugged durability , yet with simplified maintenance. The purpose of this section of the manual is to help the operator in the regular servicing of the mower . Regular maintenance at the intervals mentioned will result in the maximum efficiency and long life of t[...]

Maintenance Section 4-3 MAINTENANCE REGULAR MAINTENANCE The intervals at which regular servicing should be done are based on hours of operation. Use the tractors hour meter to determine when regular servicing is required. This symbol indicates a point that needs to be greased at an interval noted in the section below . Refer to the Detailed Mainten[...]

Maintenance Section 4-4 MAINTENANCE WEEKL Y OR EVER Y 50 HOURS ITEM SERVICE COMMENTS In T ank Hyd. Fluid Change Change after first 50 Filter hours only , then every (10 micron filter) 500 hours or yearly In-Line High Pressure Change Change after first 50 Filter hours only , then every (10 micron filter) 500 hours or yearly MONTHL Y OR EVER Y 150 HO[...]

Maintenance Section 4-5 MAINTENANCE SYMPTOMS CAUSE REMEDY Oil T emperature rises 1. Low oil level 1. Bring oil to proper level above 200 deg. F 2. Kinked/blocked hoses 2. Inspect / Repair / Replace 3. Worn pump / motor 3. Disable and repair Mower will not start 1. Blown fuse 1. Check fuse between mower or run switch and ignition / replace 2. Ball v[...]

Maintenance Section 4-6 MAINTENANCE Motor will not work 1. Excessive wear 1. Disassemble and repair . on internal parts NOTE: If flow meter is available, check pressure and flow volume for all suspected hydraulic problems. If the solution to your problem cannot be found in this section, call the T echnical Service representative at the number shown[...]

Maintenance Section 4-7 MAINTENANCE T ORQUE SPECIFICA TIONS * These are intended to be general specifications. See tractor operators or service manual for exact specifications for your unit.[...]

Maintenance Section 4-8 MAINTENANCE LUBRICA TION RECOMMENDA TIONS Description Application General Specification Recomended Mobil Lubricant Tractor Hydraulics Reservoir JD-20C Mobilfluid 424 MF M1 135,M1 141 FNHM2C134D (FNH201) Mower Hydraulics Reservoir Cold T emperatures 0 F S tart-Up ISO 46 Anti-Wear - Low T emp Mobil DTE 15M Normal T emperatures[...]

Maintenance Section 4-9 MAINTENANCE POL YCARBONA TE CARE & MAINTENANCE The proprietary UV and Abrasion Resistant surface coating on SHIELDS ® SUPERCOA TED ™ polycarbonate significantly improves performance. Periodic cleaning using proper procedures and compatible cleaners are recommended to prolong service life. T iger Corp. polycarbonate is[...]

Maintenance Section 4-10 MAINTENANCE RECOMMENDED FILLING INSTRUCTIONS FOR HYDRAULIC RESERVIORS When filling or checking the oil level, the unit should be parked on a level surface, shut “ OFF ”, and allowed sufficient time to cool to ambient temperature. Use caution when removing the pressurized breather . Do not place face over opening when re[...]

Maintenance Section 4-11 MAINTENANCE DET AILED MAINTENANCE REPLACEING HIGH PRESSURE HYDRAULIC FIL TER ELEMENT : Assure system has been shut down and de-pressurized. Locate High Pressure Filter housing. Confirm that the element that is about to be installed matches the element p/n on the filter model tag. Example: V3.0510-06 (world line 100, HD049 m[...]

Maintenance Section 4-12 MAINTENANCE GREASING INNER AND OUTER DRAFT BEAM PIVOT POINTS Locate the grease zerks on the inner and outer draft beam pivot bosses. Inject Lithium-Complex Extreme Pressure grease conforming to NLGI2-ISO 320 specifications into each zerk until grease protrudes from joints. Grease all pivots daily or every 8 hours of service[...]

Maintenance Section 4-13 MAINTENANCE With the cutter head lowered, locate the grease zerks on the linkage and pivot bosses. Inject Lithium-Complex Extreme Pressure grease conforming to NLGI2-ISO 320 specifications until it protrudes from the ends. With the cutter head in this position it is also possible to grease the draft beam cylinder anchors an[...]

Maintenance Section 4-14 MAINTENANCE GREASING PUMP DRIVE SHAFT COUPLER: With engine stopped, ensure drive shaft alignment by grasping coupler and sliding back and forth. Coupler should slide freely with approximately 1/8” of end play . If coupler does not slide freely , inspect for loose pump mount bolts, or damaged or loose crank shaft adapter .[...]

Maintenance Section 4-15 MAINTENANCE BALL V AL VES The ball valve at the hydraulic reservoir may need to be closed during certain maintenance or repair procedures. THE BALL V AL VES MUST BE OPEN (handle p arallel with valve) WHEN TRACTOR IS RE-ST ARTED OR PUMP IS COUPLED TO MOTOR OR P .T .O. ! Failure to do so may result in component failure! ADJUS[...]

Maintenance Section 4-16 MAINTENANCE GREASING SPINDLE Locate grease fitting on inside of deck housing. Inject T iger S pindle Lubricant, part number 06540000 into spindle housing. Fill with lubricant until lubricant weeps out of the top spindle seal. Lubricate spindle weekly or every 40 hours of use. TIGHTENING SPINDLE BOL TS The spindle mounting b[...]

Maintenance Section 4-17 MAINTENANCE GREASING MOTOR SPLINE T O SPINDLE SPLINE Locate motor spline and spindle spline on the mower deck. Grease splines with Mobil moly 52. Use about 4 ounces of grease. Change grease yearly or every 500 hours.[...]

Maintenance Section 4-18 MAINTENANCE ROT AR Y KNIFE REPLACEMENT 1 – Be sure you have a complete matching set of new knives for replacement. 2 – Remove knives and inspect holes for damage. Also watch for cracks in the disk around the holes. 3 – Lube threads with anti-seize, motor oil or grease. Install bolt through knife and disk from bottom s[...]

Maintenance Section 4-19 MAINTENANCE REPLACEMENT OF ROT AR Y DISK Failure to follow the following warnings and instructions may result in serious injury or damage to the equipment or property! The bolts that attach the knife mounting disk to the spindle must be grade 8. These 5/8 inch bolts are to be torqued to 204 dry or 184 oiled ft. lbs. A threa[...]

Maintenance Section 4-20 MAINTENANCE HEA VY DUTY SPINDLE ASSEMBL Y INST ALLA TION AND BEARING ADJUSTMENT W ARNING! A press MUST be used to inst all bearing cup s, bearing cones, and seals. DO NOT use a hammer to install races, bearings, or seals. The parts of assembly may be damaged. NOTE: The grease zerk and gussets are located on the top side of [...]

Maintenance Section 4-21 MAINTENANCE BEARING INST ALLA TION 1 – Press upper bearing cup into the spindle housing. 2 – T urn the spindle housing over and press in the lower bearing cup. 3 – Place the lower bearing cone in the bearing cup. Next press the seal into the spindle housing. The inner lip of the seal must be DOWN, towards the bearing,[...]

Maintenance Section 4-22 MAINTENANCE BEARING ADJUSTMENT 1 – Clamp the bottom end of the spindle securely in a vise so the spindle housing turns freely . 2 – Position a magnetic base dial indicator on the outer diameter of the spindle housing. Locate the end of the dial indicator against the flat end of the spindle shaft. The dial indicator will[...]

Maintenance Section 4-23 MAINTENANCE DAIL Y MAINTENANCE SCHEDULE The following services should be performed daily or every 8 hours of service, following the detailed maintenance instructions in the operators manual. ______ Pump Drive Shaft: Check for end play in drive shaft / coupler and lubricate at zerks. ______ Crankshaft adapter: If equipped wi[...]

Maintenance Section 4-24 MAINTENANCE[...]

P ARTS SECTION FORD TS 100A CAB, WOC, SIDE ROT AR Y Parts Section 5-1[...]

Parts Section 5-2 The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are given to help locat[...]

Parts Section 5-3 P ARTS SECTION T ABLE OF CONTENTS SECTION ASSEMBL Y P AGE TRACTOR SPECIFIC P ARTS: TRACTOR MOUNT KIT – MAIN FRAME 06101030 5-4 TRACTOR MOUNT KIT - HYDRAULICS 06101030 5-6 TRAC. MNT . KIT – AXLE / BA TT ., CAB / WOC 06101030 5-8 CABLE LIFT V AL VE – LIFT , CAB / WOC 06101044 5-10 COMBO LIFT V AL VE – LIFT , CAB / WOC 061010[...]

Parts Section 5-4 TRACTOR MOUNT KIT - MAIN FRAME[...]

Parts Section 5-5 R 7-98 TRACTOR MOUNT KIT - MAIN FRAME ITEM PART NO. QTY. DESCRIPTION 1 06300014 1 MAIN FRAME, TSA 100 2 06380001 1 REAR RESERVOIR SUPPORT 3 06380002 1 FRONT RESERVOR SUPPORT 4 32667 1 R E S E R V O I R T ANK FRAME 5 32669 1 RESERVOIR T ANK STRAP 06700006 A V AIL. RESERVOIR T ANK ASSY , TSA. 6 21627 4 NYLOCK NUTS 7 06380000 1 R E S[...]

Parts Section 5-6 TRACTOR MOUNT KIT - HYDRAULICS, BRAKE V AL VE[...]

Parts Section 5-7 4-22-02 TRACTOR MOUNT KIT - HYDRAULICS, BRAKE V AL V E ITEM PART NO. QTY. DESCRIPTION 1 32869 1 NIPPLE,MALE LONG ,1MOR X 1MJ 4 34067 1 ADAPTER,1 1/4MORX1 1/4MJ 5 34069 1 BALL V AL VE,1 1/4FOR 7 23568 4 HOSE CLAMP (NOT SHOWN) 8 6T3200 3 SPLIT HOSE (NOT SHOWN) 9 06500065 1 HOSE,1 1/4x55(1 1/4FJXx20FLG45) 1 1 TF4852 2 #20 FLANGE KIT [...]

Parts Section 5-8 TRACTOR MOUNT KIT - BRACE/BA TT , CAB/WOC[...]

Parts Section 5-9 R 5-00 TRACTOR MOUNT KIT - BRACE/BA TT , CAB/WOC ITEM PART NO. QTY. DESCRIPTION 1 0630001 1 1 AXLE BRACE, RH NHTSA 1 15 1A 06300012 1 AXLE BRACE, LH NHTSA 1 15 2 21833 2 CAPSCREW - 3/4" X 2 1/4" 3 21993 8 LOCKWASHER - 3/4" 4 21825 6 HEX NUT - 3/4" 5 0637001 1 1 B A TT M N T , TS 100-135A 6 * 2 EXISTING HARDWARE[...]

Parts Section 5-10 CABLE LIFT V A L VE - SIDE ROT AR Y , CAB/WOC[...]

Parts Section 5-11 R 7-98 CABLE LIFT V A L VE - SIDE ROT AR Y , CAB/WOC ITEM PART NO. QTY. DESCRIPTION 1 31320 1 VALVE,2SP,HSC,TM,LS 2 34622 1 VALVE MOUNTING PLATE 3 06340008 1 VALVE MOUNTING ANGLE, LF 4 06340009 1 VALVE MOUNTING ANGLE, RF 5 34520 1 SWITCH BOX, BOOM 6 23865B 1 CABLE CONTROL MOUNTING BRACKET 7 6T1251 2 CABLE CONTROL BOX 8 34623 2 CO[...]

Parts Section 5-12 COMBO LIFT V AL VE - SIDE ROT AR Y , CAB/WOC[...]

Parts Section 5-13 R 7-98 COMBO LIFT V AL VE - SIDE ROT AR Y , CAB/WOC ITEM PART NO. QTY. DESCRIPTION 1 31321 1 VALVE,2SP,HSC,TM,LS 2 34622 1 VALVE MOUNTING PLATE 3 06340008 1 VALVE MOUNTING ANGLE, LF 4 06340009 1 VALVE MOUNTING ANGLE, RF 5 34520 1 SWITCH BOX, BOOM 6 23865B 1 CABLE CONTROL MOUNTING BRACKET 7 6T1251 2 CABLE CONTROL BOX 8 34623 2 CON[...]

Parts Section 5-14 MIRROR BRACKET[...]

Parts Section 5-15 MIRROR BRACKET ITEM PART NO. QTY. DESCRIPTION 1 * 1 WORK LIGHT (EXISTING) 2 * 1 MIRROR KNOB (EXISTING) 3 * 1 MIRROR (EXISTING) 4 * 1 EXHAUST MUFFLER (EXISTING) 5 06370008 1 MNT ,MIRROR/LIGHT ,TS1 15A 6 06410141 1 COLLAR,EXHAUST ,TS1 15A 7 06410142 1 COLLAR,CLAMP ,EXHAUST ,TS1 15A 8 21530 2 CAPSCREW ,1/4 X 1 NC 9 21525 4 HEX NUT ,[...]

Parts Section 5-16 BOOM POL YCARBONA TE CAB SAFETY WINDOW KIT ITEM PART NO. QTY. DESCRIPTION 1 06490004 1 P O L YCARBONA TE, NHTSA 1 15, DOOR, RH 2 31965 17’ TRIM SEAL, 3/8 CLIP X 3/4 OD BULB 3 06530502 2 CAPSCREW 8 MM X 40 MM GR8 4 * * EXISTING HARDWARE 5 06530501 1 CAPSCREW 6 MM X 25 MM GR8 6 06537006 1 THREADED INSERT 1/4 X 1/2 NC 7 21532 1 CA[...]

Parts Section 5-17 NON-CAB STEEL CANOPY - OPTIONAL ITEM PART NO. QTY. DESCRIPTION 1 6T6902 1 CANOPY 2 32730 2 S P ACER CANOPY BRACKET 3 32727 2 CANOPY BRACKET 4 0642003 4 U-BOL T ,3.25x5.00x.50,20NF ,GR8 5 21700 1 4 HEX NUT - 1/2" NF 6 21990 1 4 LOCKWASHER - 1/2" 7 21730 6 CAPSCREW - 1/2" X 1 1/4" 8 28053 4.8' TRIM-LOCK 9 2[...]

EXHAUST MOUNT ITEM PART NO. QTY. DESCRIPTION 1 06410127 1 MNT ,EXHAUST ,TSA100-1 10 2 21630 4 CAPSCREW ,3/8 x 1,NC 3 21625 4 HEX NUT ,3/8,NC 4 21988 4 LOCKWASHER,3/8 5 * 2 EXISTING MAINFRAME HARDWARE 6 06410128 1 MNT ,EXHAUST ,SUPPORT 7 35188 2 C LAMP ,EXHAUST ,3” 8 06520024 1 TUBE,EXHAUST ,SUPPORT ,4CYL 9 06520035 1 CLAMP ,EXHAUST ,2.75,SS,WRAP [...]

R 7-98 OPTIONAL PUMP AND GRILL GUARD KIT ITEM PART NO. QTY. DESCRIPTION 1 32430 1 UNIVERSAL PUMP GUARD 2 32737 1 U N I V E R S A L GRILL GUARD 3 21833 4 CAPSCREW - 3/4 X 2 1/4 4 22021 2 FLATWASHER - 3/4 5 21993 4 LOCKWASHER - 3/4 6 21825 4 HEX NUT - 3/4[...]

Parts Section 5-20 BRAKE V A L VE SOLENOID 12-17-02 ITEM PART NO. QTY. DESCRIPTION * 34115 AV A I L SOLENOID BRAKE VALVE ASSEMBLY - HIGH PRESSURE 1 34092 1 BRAKE VALE, BLANK 2 34095 1 RELIEF VALVE, 3000 PSI 3 34094 2 LOGIC ELEMENT 4 34093 1 SOLENOID, 2 POSITION, 3 WAY 5 34091 1 RELIEF VALVE, 2600 PSI ** 34096 2 RELIEF SEAL KIT ** 34097 1 SOLENOID S[...]

Parts Section 5-21 R 7-98 ITEM PART NO. QTY. DESCRIPTION 27401 A V AIL. SWITCH ASSEMBL Y 1 31301 1 SWITCH BOX 2 6T3923 1 SWITCH “ON” LIGHT 3 6T3924 1 FUSE HOLDER 4 6T3931 O P T . TEMPERA TURE SENSOR 5 6T3934 OP T . O I L TEMPERA TURE GUAGE SOLENOID V A L VE SWITCH AND WIRING[...]

Parts Section 5-22[...]

Side Rotary Common Section 6 - 1 SIDE ROT AR YCOMMON SECTION COMMON P ARTS SECTION[...]

Side Rotary Common Section 6 - 2 T ABLE OF CONTENTS SECTION ASSEMBL Y P AGE CABLE LIFT ASSEMBL Y 6-4 COMBO DRAFT BEAM 6-6 60” SIDE CABLE ROT ARY MOWER ASSEMBL Y 6-8 72” SIDE CABLE ROT AR Y MOWER ASSEMBL Y 6-10 60” SIDE COMBO RTR Y MOWER ASSEMBL Y 6-12 60” SIDE RO T ARY MOWER 6-14 60” SPINDLE AND SP ACER 6-16 72” SIDE COMBO ROT ARY MOWER[...]

Side Rotary Common Section 6 - 3 The following instructions are offered to help eliminate needless delay and error in processing purchase orders for the equipment in this manual. 1. The Parts Section is prepared in logical sequence and grouping of parts that belong to the basic machine featured in this manual. Part Numbers and Descriptions are give[...]

Side Rotary Common Section 6 - 4 CABLE LIFT ASSEMBL Y 3-22-02[...]

Side Rotary Common Section 6 - 5 CABLE LIFT ASSEMBL Y ITEM P ART NO. QT Y . DESCRIPTION 1 6T0103A 1 DRAFT BEAM (STD 25 LB, 45 3/8”) 6T0103E OP T . DRAFT BEAM (EXTENDED 6” 4WD) 6T0103L OP T . DRAFT BEAM (EXTENDED 15”) 6T0105 O P T . D R A F T BEAM (STD WITH TRA VEL LOCK) 6T0108 O P T . DRAFT BEAM (30 LB CHANNEL, 45 3/8”) 2 6T0150 1 CYLINDER [...]

Side Rotary Common Section 6 - 6 COMBO DRAFT BEAM 3-22-02[...]

Side Rotary Common Section 6 - 7 COMBO DRAFT BEAM ITEM P ART NO. QT Y . DESCRIPTION 1 06350001 1 COMBO DRAFT BEAM - STD DTY ROT ARY 31063 OP T . COMBO DRAFT BEAM - HVY DTY ROT ARY 2 6T0151R 1 HYD. CYLINDER 3” X 10” 3 32215 1 HYD. CYLINDER 3” X 12” - STD DTY 25343 REF HYD. CYLINDER 3” X 12” - HVY DTY 4 TF4500A 1 P I VO T A R M 5 TF4507B [...]

Side Rotary Common Section 6 - 8 60” SIDE CABLE ROT AR Y MOWER[...]

Side Rotary Common Section 6 - 9 60” SIDE CABLE ROT AR Y MOWER ITEM P ART NO. QT Y . DESCRIPTION 1 32099 1 RT RY , 60" WELDMENT , 1/4" DECK 21225B 1 RTR Y , 72” WELDMENT , 1/4” DECK 2 22592 1 FLAP , DEFLECTOR, TM60 3 6T0823 1 BAR, FLAP , TM60 4 6T0822 2 SHIM, MOTOR MOUNT , 14GA. (AS NEEDED) 5 6T0822A 2 SHIM, MOTOR MOUNT , 18 GA. (AS[...]

Side Rotary Common Section 6 - 10 72” SIDE CABLE ROT AR Y MOWER[...]

Side Rotary Common Section 6 - 11 72” SIDE CABLE ROT AR Y MOWER ITEM P ART NO. QT Y . DESCRIPTION 1 21225B 1 RTR Y , 72” WELDMENT , 1/4” DECK 2 21295B 1 FLAP , DEFLECTOR, TM72 3 21242A 1 BAR, FLAP , TM72 4 6T0822 2 SHIM, MOTOR MOUNT , 14GA. (AS NEEDED) 5 6T0822A 2 SHIM, MOTOR MOUNT , 18 GA. (AS NEEDED) 6 6T1001 1 BRKT , MOTOR MTG , 60"SI[...]

Side Rotary Common Section 6 - 12 60” SIDE COMBO ROT AR Y MOWER[...]

Side Rotary Common Section 6 - 13 60” SIDE COMBO ROT AR Y MOWER ITEM P ART NO. QT Y . DESCRIPTION 1 32617 1 RT RY , 60" DECK, COMBO - SDT DUTY 30188D 1 R T R Y , 60” DECK, COMBO - HEA VY DUTY 2 31773 1 GAURD,CHAIN,FRONT ,SR60 3 6T1001 1 BRKT , MOTOR MTG , 60"SIDE RTRY 4 6T0820H 2 SKID SHOE, TM60, HEA VY DUTY 5 22592 1 FLAP , DEFLECTOR[...]

Side Rotary Common Section 6 - 14 60” SIDE ROT AR Y MOWER 8/26/05[...]

Side Rotary Common Section 6 - 15 60” SIDE ROT AR Y MOWER ITEM P A R T N O . Q TY . DESCRIPTION 1 34975 1 H E A VY DUTY GRASSKA T COMBO 06320005 1 S T D DU T Y GRASSKA T COMBO 06320008 1 H E A V Y DUTY GRASSKA T CABLE 2 34980 1 SPINDLE ASSY ,TM 60" 3 06504016 1 C U R RENT MOTOR,(M365-1 1/4" 14-SPLINE) 34981 1 ORIGINAL MOTOR,(M365-1 1/4&[...]

Side Rotary Common Section 6 - 16 60” SIDE ROT AR Y SPINDLE AND SP ACER[...]

Side Rotary Common Section 6 - 17 60” SIDE ROT AR Y SPINDLE AND SP ACER ITEM P A RT NO . QTY . DESCRIPTION 1 34975 1 H E A V Y DUTY GRASSKA T COMBO 06320005 1 STD DUTY GRASSKA T COMBO 06320008 1 H E AVY DUTY GRASSKA T CABLE 2 34980 1 SPINDLE ASSY ,TM 60" 3 0632001 1 2 SP ACER,TSR,SPINDLE 4 06533004 8 F L A T W ASHER,1/2,SAE,GR 8 5 06530221 8[...]

Side Rotary Common Section 6 - 18 72” SIDE COMBO ROT AR Y MOWER[...]

Side Rotary Common Section 6 - 19 72” SIDE COMBO ROT AR Y MOWER ITEM P ART NO. QT Y . DESCRIPTION 1 34260 1 RT RY , 72" DECK, COMBO - SDT DUTY 31408A 1 RT RY , 72” DECK, COMBO - HEA VY DUTY 2 31931 1 GAURD,CHAIN,FRONT ,SR60 3 6T1001 1 BRKT , MOTOR MTG , 60"SIDE RTRY 4 21248 2 SKID SHOE, TM72 5 21295B 1 FLAP , DEFLECTOR, TM72 6 21242A [...]

Side Rotary Common Section 6 - 20 TM72” MOTOR ASSEMBL Y ITEM P ART NO. QT Y . DESCRIPTION 1 06504018 1 MOTOR 2 TF4852 2 K I T ,FLANGE,#20 3 34943 2 ELBOW ,#20FLG x #16MJ 4 24724 1 ELBOW ,#16FJX x #16MJ45 5 06500444 1 HOSE,#16 x 141 6 06500445 1 HOSE,#16 x 145[...]

Side Rotary Common Section 6 - 21 P AGE INTENSIONALL Y LEFT BLANK[...]

Side Rotary Common Section 6 - 22 CHAIN GUARDS[...]

Side Rotary Common Section 6 - 23 SIDE ROT AR Y CHAIN GUARDS 60” SIDE ROT AR Y ITEM P ART NO. QTY . DESCRIPTION 31773 STD. GAURD,CHAIN,SR60,FRONT ASSY 1 31762 1 GUARD,CHAIN,TM60,FRONT 2 28407 12’ CABLE, 5/16”, BULK 3 22993 7 7 CHAIN, 5/16” GR30, 9 LINK ** 28408 4 U-BOL T , CABLE, 5/16” ** NOT SHOWN 72” SIDE ROT AR Y ITEM P ART NO. QTY .[...]

Side Rotary Common Section 6 - 24 SIDE ROT AR Y CASTER WHEEL ASSEMBL Y[...]

Side Rotary Common Section 6 - 25 SIDE ROT AR Y CASTER WHEEL ASSEMBL Y ITEM P ART NO. QTY . DESCRIPTION 1 25214C 1 FRAME,CASTER,WHL,TM60,W/O CG 2 22057C 1 SPINDLE, CASTER AXLE, ASSY 3 6T2617 2 BUSHING ,MACH,1-1/2IDX 2-1/4OD 4 28548 1 CASTER WHEEL, SOLID TIRE ** 22065 1 HUB ASSY , REAR ROT AR Y ** 22066 1 H UB , C A S T E R ( R E A R R O T A RY ) **[...]

Side Rotary Common Section 6 - 26 RESER VOIR T ANK FIL TER ASSEMBL Y[...]

Side Rotary Common Section 6 - 27 RESER VOIR T ANK FIL TER ASSEMBL Y ITEM P ART NO. QT Y . DESCRIPTION 06505044 A V A IL F I L TER ASSY SAE 10 MICRON 1 28583 4 CAPSCREW ,8MMX25MM(1.25 PITCH) 2 06505045 1 COVER 3 06505046 1 SEAL KIT 4 06505047 1 SPRING 5 06505048 1 B Y PA S S 6 35259 1 FI L TER,10 MIC,RETURN LINE 7 06505049 1 CAN/BODY[...]

Side Rotary Common Section 6 - 28 MOWER SPINDLE ASSEMBL Y - 6T1024H5[...]

Side Rotary Common Section 6 - 29 MOWER SPINDLE ASSEMBL Y - 6T1024H5 ITEM P ART NO. QT Y . DESCRIPTION 6T1024H5 A V AI L SPINDLE ASSEMBL Y COMPLETE 1 6T1031 1 SPROCKET 2 6T1016 1 BEARING LOCK NUT - THICK 3 22596 1 JAM WASHER 4 6T1015 1 BEARING ADJUSTMENT NUT - THIN 5 6T1014 1 BEARING ADJUSTMENT SLEEVE 6 6T101 1 1 U P P E R SEAL - SET OF 2 7 6T1012 [...]

Side Rotary Common Section 6 - 30 MOWER SPINDLE ASSEMBL Y - 34980[...]

Side Rotary Common Section 6 - 31 MOWER SPINDLE ASSEMBL Y - 34980 ITEM P A RT NO . QTY . DESCRIPTION 1 34978 1 SPINDLE MOUNT 2 34979 1 SPINDLE,TM60",NEW 3 6T1013 1 BEARING CUP 4 6T1012 1 BEARING ,CONE 5 6T101 1 2 S E A L , U P P E R (SET OF 2) 6 6T1014 1 SLEEVE,ADJ BEARING 7 6T1013H 1 BEARING CUP ,HD 8 6T1012H 1 BEARING ,CONE,HD 9 6T101 1H 1 S[...]

Side Rotary Common Section 6 - 32 HYDRAULIC LIFT CYLINDER[...]

Side Rotary Common Section 6 - 33 HYDRAULIC LIFT CYLINDER 3” X 12” CYLINDER # 32215 ITEM P ART NO. QTY . DESCRIPTION 1 6T0167 1 CYLINDER BUTT 2 6T0170 1 CYLINDER GLAND 3 6T0178 1 CLEVIS END 4 6T0204 1 CYLINDER TUBE 5 6T0203 1 PISTON ROD 6 6T0173 1 PISTON 7 6T0179 1 LOCKNUT 8 6T0205 1 TIE ROD ASY 6T0187 A V AI L SEAL KIT 9 2 O - RING 1 0 2 BACK [...]

Side Rotary Common Section 6 - 34 ROT AR Y KNIVES AND DISKS ITEM P ART NO. QTY . DESCRIPTION 1 34876 1 BLADE MOUNTING DISK 2 6T1023R 2 NYLOCK HEX NUT 1 1/8” 3 34878 2 S P ACER 4 34497 2 KNIFE MOUNTING BOL T 5 34685 2 KNIFE,60" HIGH SUCTION - ST ANDARD 5A 34684 2 KNIFE,60" - OPTIONAL 6 34682 2 KNIFE 72” - MOUNT ON 72” MOWER ONL Y 7 2[...]

Side Rotary Common Section 6 - 35 CASTER WHEEL ASSEMBL Y ITEM P ART NO. QTY . DESCRIPTION 1 21459 1 SPINDLE, CASTER WHEEL AXLE 2 21987 5 LOCKWASHER, 5/16” 3 21575 5 HEX NUT , 5/16” 4 28548 5 CAPSCREW , 5/16” x 3/4”, NC 5 22697-1 1 RIM, OUTER/RR RTRY CASTER ASSY 6 21416 1 TIRE,SOLID,RR-RTRY 7 22696-1 1 RIM,REAR ROT ARY CASTER 8 22070 1 DUST [...]

Side Rotary Common Section 6 - 36 ROT AR Y MOT OR[...]

Side Rotary Common Section 6 - 37 ROT AR Y MOT OR ITEM P ART NO. QT Y . DESCRIPTION 06504018 MOTOR 06504103 1 SEAL KIT 1 22790 1 HOUSING , SEC 2 06504088 1 HOUSING , SEC 3 06504062 1 HOUSING , GEAR 4 06504105 1 S E T , GEAR SHAFT 5 06504106 4 CAP SCREW 6 06504078 2 SCREW , DRIVE 7 06504092 1 K E Y 8 06504093 4 PIN, DOWEL 9 06504094 1 NAME PLA TE 1 [...]

Side Rotary Common Section 6 - 38 HYDRO PUMP & TSR MOTOR TSR MOTOR FRONT PUMP[...]

Side Rotary Common Section 6 - 39 HYDRO PUMP & TSR MOTOR FRONT HYDRAULIC PUMP ITEM P ART NO. QTY . DESCRIPTION 23152 A V A IL PUMP ASSEMBL Y 1 3/4” COMPLETE 1 22765 1 SEAL (INCLUDED IN SEAL KIT) 2 22766 1 SHAFT END COVER 3 22767 2 CHECK AND END COVER 4 22768 2 BUSHING 5 22769 2 CHANNEL SEAL (INCLUDED IN SEAL KIT) 6 22770 2 THRUST PLA TE (INCL[...]

Side Rotary Common Section 6 - 40 SIDE COOLER[...]

Side Rotary Common Section 6 - 41 SIDE COOLER ITEM PART NO. QTY. DESCRIPTION 1 21530 1 0 CAPSCREW ,1/4 X1 NC 2 21986 1 0 LOCKWASHER,1/4 3 22014 1 0 F L A T W ASHER,1/4 4 35176 1 0 1/4 U-NUT 5 06370015 1 SCREEN,COOLER,FRNT 6 06380006 1 M N T ,COOLER,BUMPER T ANK,RH 7 06380007 1 M N T ,COOLER,BUMPER T ANK,LH 8 06510026 1 COOLER,FRONT MNT 9 21629 4 CA[...]

Side Rotary Common Section 6 - 42 2SP HUSCO - POWER BEYOND (30801)[...]

Side Rotary Common Section 6 - 43 2SP HUSCO - POWER BEYOND (30801) ITEM P ART NO. QT Y DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1702 1 END COVER, POWER BEYOND 3 TB1017P 1 V AL VE SECTION (SINGLE ACTING , SPRING DETENT) 4 06502091 1 V AL VE SECTION (DOUBLE ACTING , CENTER SPRING) (NO AUX V AL VE PORTS) 5 N/A - N/A 6 N/A - N/A 7 TB1017M 1 SHUT -OF[...]

Side Rotary Common Section 6 - 44 2 SP HUSCO - LOAD SENSE (31320)[...]

Side Rotary Common Section 6 - 45 2 SP HUSCO - LOAD SENSE (31320) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 4 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 5 06503067 1 RELIEF PLUG 6 06503067 1 RELIEF PLUG 7 N/A - N/A 8 6T4209 1 RE[...]

Side Rotary Common Section 6 - 46 2 SP HUSCO - LOAD SENSE (31321)[...]

Side Rotary Common Section 6 - 47 2 SP HUSCO - LOAD SENSE (31321) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 4 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 5 06503067 1 RELIEF PLUG 6 31861 1 RELIEF V AL VE, 360 PSI 7 N/A - N/A 8 6T[...]

Side Rotary Common Section 6 - 48 2SP HUSCO - POWER BEYOND (31752)[...]

Side Rotary Common Section 6 - 49 2SP HUSCO - POWER BEYOND (31752) ITEM P ART NO. QT Y DESCRIPTION 1 TB1017S 1 INLET END COVER 2 TB1702 1 END COVER, POWER BEYOND 3 TB1017P 1 V AL VE SECTION (SINGLE ACTING , SPRING DETENT) 4 TB1017P 1 V AL VE SECTION (SINGLE ACTING , SPRING DETENT) 5 N/A - N/A 6 N/A - N/A 7 TB1017M 1 SHUT -OFF PLUG 8 TB1017E 1 RELIE[...]

Side Rotary Common Section 6 - 50 2SP HUSCO - LOAD SENSE (06502040)[...]

Side Rotary Common Section 6 - 51 2SP HUSCO - LOAD SENSE (06502040) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) 4 31597 1 V AL V E SECTION (DOUBLE ACTING , CENTER SPRING) (REMOVE SHUTTLE DISC) 5 06503067 1 RELIEF PLUG 6 06503067 1 RELIEF PLUG 7[...]

Side Rotary Common Section 6 - 52 2SP HUSCO - LOAD SENSE (06502042)[...]

Side Rotary Common Section 6 - 53 2SP HUSCO - LOAD SENSE (06502042) ITEM P ART NO. Q T Y DESCRIPTION 1 31595 1 INLET END COVER 2 31594 1 END COVER, LOAD SENSE 3 31600 1 V AL V E SECTION (DOUBLE ACTING , DETENT FLOA T) 4 31600 1 V AL V E SECTION (DOUBLE ACTING , DETENT FLOA T) (REMOVE SHUTTLE DISC) 5 06503067 1 RELIEF PLUG 6 31861 1 RELIEF V AL VE 3[...]

Side Rotary Common Section 6 - 54 ITEM PART NO. QTY. DESCRIPTION 06502007 A V A IL V AL VE A S Y HIGH PRESSURE 06502008 A V A I L V A LVE A S Y L O W P RESSUTE 1 34689 1 SOLENOID COIL 2 06505026 1 SOLENOID 3 06502009 1 SOLENOID V AL VE KIT 4 6T391 1 1 SOLENOID SEAL KIT 5 6T3908 1 RELIEF PILOT 2150 PSI LOW PRESSURE 6 6T3910 1 RELIEF PILOT 3400 PSI H[...]

Side Rotary Common Section 6 - 55 SOLENOID BRAKE V AL VE ASSEMBL Y ITEM PART NO. QTY. DESCRIPTION * 34115 AV A I L SOLENOID BRAKE VALVE ASSEMBLY - HIGH PRESSURE 1 34092 1 BRAKE VALVE, BLANK 2 34095 1 RELIEF VALVE, 3000 PSI 3 34094 2 LOGIC ELEMENT 4 34093 1 CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER) 5 34091 1 RELIEF VALVE, 2600 PSI 6 34689[...]

Side Rotary Common Section 6 - 56 BRAKE V A L VE ASSEMBL Y W/ METRI P A K ITEM PART NO. QTY. DESCRIPTION 1 34092 1 BRAKE VALVE, BLANK 2 34094 2 LOGIC ELEMENT 3 34095 1 RELIEF VALVE, 3500 PSI 4 06510095 1 METRI PAK COIL 5 34093 1 CARTRIDGE, 2 POSITION, 3 WAY (WITH NUT & WASHER) 6 34091 1 RELIEF VALVE, 2600 PSI[...]

Side Rotary Common Section 6 - 57 SOLENOID BRAKE V A L VE HYDRAULIC SCHEMA TIC BRAKE V A L VE TROUBLESHOOTING F AILURE MODE: CHECK STEPS - MOWER WILL NOT ST ART - system pressure is low (engine not lugging). 1 thru 6 - MOWER WILL NOT ST AR T - system pressure is high (engine lugging). “MR” port will be high pressure. 7 - MOWER WILL NOT ROT A TE[...]

Side Rotary Common Section 6 - 58 TRA VEL LOCK LIFT BEAM ITEM PART NO. QTY. DESCRIPTION 1 6T0105 1 DRAFT BEAM (STD WITH TRA VEL LOCKS) 2 6T0106 1 T R A V E L LOCK BRACKET 3 6T0107 2 T R AV E L LOCK PINS 3/4” X 3 1/4” 4 6T3020 2 R - CLIP 5/32” 5 21833 1 CAPSCREW 3/4” X 2 1/4” 6 21825 1 HEX NUT 3/4” 7 21993 1 LOCK WASHER 3/4” 8 22021 1 [...]

Side Rotary Common Section 6 - 59 SIDE MOWER TRA VEL LOCK (COMBO) ITEM PART NO. QTY. DESCRIPTION 1 R E F * COMBO DRAFT BEAM- REFER TO DRAFT BEAM P ARTS 2 6T0106 1 T R A V E L LOCK BRAKCET 3 6T0107 2 T R AVE L LOCK PIN (3/4” x 3-1/4”CAPPED) 4 6T3020 2 R-CLIP , 5/32” 5 21833 1 CAPSCREW , 3/4” x 2-1/4” NC 6 21825 1 HEX NUT , 3/4” NC 7 2199[...]

Side Rotary Common Section 6 - 60 SWITCHBOX SER VICE P ARTS ITEM P / N QT Y . DESCRIPTION 1 06514013 1 SWBX,ALUM,BLK,06510102 2 35226 1 SWITCH,MOWER,COLEHERSEE 3 3381 1 1 SWITCH,MASTER/DECK FLOA T 4 6T3923 1 INDICT A TOR LIGHT ,ON,RED 5 06514014 1 BREAKER,10A,SWBX 6 34540 1 STRAIN RELIEF ,3/4,BLACK,NYLON 7 06550018 1 DECAL,SWTCHBX,TM/TSF ,CG 8 3522[...]

Side Rotary Common Section 6 - 61 SWITCHBOX SCHEMA TIC[...]

Side Rotary Common Section 6 - 62[...]

W ARRANTY SECTION Warranty Section 7-1[...]

.[...]

W ARRANTY INFORMA TION T iger Corporation, 3301 N. Louise, Sioux Falls, South Dakota, warrants to the original Retail Customer , the new T iger equipment is free of defects in material and workmanship. Any part of equipment that in T iger ’s judgement, show evidence of such defects will be repaired or replaced without charge, provided that the fa[...]

ONE LAST WORD This manual cannot possibly cover all of the potentially hazardous situations you will encounter . By being familiar with the safety rules, operating and maintenance instructions in this manual you can help prevent accidents. The objective of this manual is to help make you a better operator . Remember , SAFETY IS YOU! Y our safety an[...]

T O THE OWNER / OPERA TOR / DEALER T o keep your implement running ef ficiently and safely , read your manual thoroughly and follow these directions and the Safety Messages in this manual and on the machine. The table of contents clearly identifies each section where you can easily find the information you need. The Occupational Safety and Health A[...]

Printed in USA © T iger Corporation[...]