Turbo Chef Technologies i5 инструкция обслуживания

Accelerating the World of Cooking TM Ser vice Manual FOR THE TURBOCHEF i5 RAPID COOK O VEN[...]

[...]

F or further information, call 800.90TURBO or +1 214.379.6000[...]

The information contained in this manual is important for the proper installation, use, maintenance, and repair of this o ven. F ollow these procedures and instructions to help ensur e satisfactor y baking results and years of trouble-fr ee ser vice. Errors – descriptive, typographic, or pictorial – ar e subject to correction. S pecifications a[...]

Safety Instruc tions General Safety I nformation i Reducing F ire Risk i G rounding Instructions ii P o wer Cord R eplacement ii P recautions to be Observed Before and D uring Servicing to A void P ossible E xposure to Excessive M icrowave E nergy ii RF Interference Considerations ii Specifications and Installation Theory of Operation 1 Certificati[...]

Resetting the Oven 14 T urning Oven Options On/O ff 14 Setting the Language 14 Setting the Date/T ime 14 T est Mode - T esting Oven P arts 15 T est Mode - S tatus Indicators 15 T est Mode - F ault Log 15 T est Mode - T urning On/Off Diagnostic M ode 15 T est Mode - S elf T est 16 T est Mode - M anufacturing Mode 16 Micro wave Leakage T est (Ho w to[...]

Overview of the Microwave S ystem 29 Capacitors 29 T esting a Capacitor 29 F ilament T ransformers 29 Wiring the F ilament T ransformers 29 High-V oltage T ransformers 30 Wiring the H igh-V oltage T ransformers 30 T esting a F ilament or High-V oltage T ransformer 30 High-V oltage Diodes 30 T esting a High-V oltage Diode 31 Magnetrons 32 T esting a[...]

T roubleshooting Overview of T roubleshooting 37 F ault Code Descriptions 37 F ault Code T roubleshooting - F1 Blower R unning Status B ad 39 F ault Code T roubleshooting - F2 Cook T emperature Low 40 F ault Code T roubleshooting - F3 Magnetron C urrent Low 41 F ault Code T roubleshooting - F4 Door M onitor Defective 42 F ault Code T roubleshooting[...]

i Safety Instruc tions S trictly adhere to the following safety precautions to r educe the risk of burns, electric shock, fire, injury , damage to oven or pr operty near oven, or possible exposure to ex cessive microwave energy . General Safety Information  Read all instructions before using this appliance.  Read and follo w the specific &quo[...]

Grounding Instructions This appliance must be grounded. In the ev ent of an electrical short circuit, grounding reduces the risk of electric shock by pro viding an escape wire for the electric current. This oven is equipped with a cor d that has a grounding wire with a grounding plug, which must be plugged into an outlet that is pr operly installed[...]

Specifications and I nstallation[...]

SPECIFICA TIONS AND INST ALLA TION 1 Theor y of Operation The i5 rapid cook oven combines pr ecisely- controlled impinged air and micro wave energy to create higher heat transfer rates than conventional ovens. T op-launched microwave and impinged air are stirred to further ensure ev en heat distribution, while impinged air enters the cavity from th[...]

2 SPECIFICA TIONS AND INST ALLA TION Single Phase i5 US model (i5-9500-1) V oltage: 208/240 V AC* F requency: 60 Hz Curr ent: 48 amps Max I nput: 9500/11500 watts Plug: NEMA 6-50P i5 UK model (i5-9500-2-UK) V oltage: 230 V AC F requency: 50 Hz Curr ent: 48 amps Max I nput: 10000 watts Plug: IEC 309, 3-pin i5 BK model (i5-9500-6-BK) V oltage: 220 V [...]

SPECIFICA TIONS AND INST ALLA TION 3 F igure 2: Hand Grip Locations Unpacking I nstructions 1. Remo ve oven fr om packaging. 2. Before discar ding packaging, check thoroughly for accessories, consumables, and literature. 3. Discar d packaging. 4. Check cook cavity thoroughly for accessories, consumables, and literature. Discar d any packaging. Lift[...]

4 SPECIFICA TIONS AND INST ALLA TION Installation Near Open Heat Source See F igure 4, page 5. When placing a T urboChef oven near an open heat source, strictly adhere to the follo wing: - If the ov en is being placed near a grill or stove, a divider must exist between the ov en and the open heat source, with a minimum of 6” (152 mm) between the [...]

SPECIFICA TIONS AND INST ALLA TION 5 27.8” (706 mm) 32.0” (813 mm) 26.625” (676 mm) F igure 5: Oven Car t Dimensions Grill Partition 24.3” (618 mm) Above Counter Top T urboChef i5 Oven 6” (152 mm) Minimum 12” (305 mm) Minimum Deep Fryer Counter T op / T able Partition 24.3” (618 mm) Above Counter Top F igure 4: Installation Near Open [...]

6 SPECIFICA TIONS AND INST ALLA TION This page intentionally left blank .[...]

Daily Maintenance[...]

DAIL Y MAINTENANCE 7 Step 1: P repare the Oven W ARNING: Oven operates at appr oximately 450°F (232°C) and may cause injury if not allowed to cool properly . - T urn off the oven by pr essing the On/Off key . - Slightly open the ov en door . Cooling takes approximately 40 minutes. - DO NOT attempt to clean the o ven until the oven displays “Ove[...]

8 D AIL Y MAINTENANCE Step 7: Clean and Dry the O ven Door CAUTION: DO NO T spray oven cleaner directly onto the o ven door gasket (reference “ A” in adjacent photo) or saturate it with water . CAUTION: DO NO T scrub or attempt to clean the oven door gasket. D oing so may cause the oven door to misalign, r esulting in a non-warranty ser vice ca[...]

O ven C ontr ols and C ook ing[...]

OVEN C ONTROLS AND COOKING 9 Oven Controls 1. Info Key When the oven is off or cooling do wn, press to access the INFO MODE (see page 13). 2. On/Off Key When the oven is cooling do wn or off, press to turn on the oven. When the oven is on or warming up , press to turn off the oven. When the oven is in the INFO MODE (see page 13), press to return th[...]

10 OVEN C ONTROLS AND COOKING Cooking This section explains how to cook a food product by describing the “ standard operation ” modes through which the ov en progresses. The oven is pr eprogrammed with recipe settings at the time of manufacture and is ready to operate out of the box. If these settings are erased, new menu settings must be eithe[...]

OVEN C ONTROLS AND COOKING 11 Happens When... - The oven completes MODE 10. Goes T o... - MODE 2 when On/Off key is pressed. - INFO MODE (page 13) when Info key is pressed. Mode 2: T emperature Select NO TE: If cooking with only one temperature, this screen will be bypassed. The i5 Oven can store up to four differ ent cook temperature settings. Eac[...]

12 OVEN C ONTROLS AND COOKING The ADJUST TIME MODE can be turned on or off from the “Options ” screen (see page 14). I t is turned off by default. Happens When... - ADJUST TIME MODE is enabled and a food item is selected from MODE 5. Goes T o... - MODE 7 when “S tart Cook” is selected. - MODE 10 if the On/Off key is pressed. Mode 7: Cooking[...]

OVEN C ONTROLS AND COOKING 13 Over view of the Info Mode The INFO MODE serves four main purposes: 1. T o display oven information. 2. T o provide access to TEST MODE and additional diagnostic tools for service technicians. 3. T o turn oven options and features on/off . 4. T o update oven settings. T o access the INFO MODE , simply press the Info ke[...]

I nf o M ode[...]

14 INFO MODE Resetting the Oven Resetting the o ven is one way to potentially clear an error message, should one occur . F rom screen 1 of the INFO MODE , press the R5 soft key . T urning Oven Options On/O ff F igure 12. F rom screen 2 of the INFO MODE , pr ess the L2 soft key to access the “Options ” screen. When prompted, enter the password 9[...]

INFO MODE 15 T est Mode - T esting O ven P ar ts F rom screen 2 of the I nfo mode, press the L1 soft key to access TEST MODE . When prompted, enter the password 9 4 2 8 and press the Enter key . F rom TEST MODE , the oven ’ s components can be tested independently , or a comprehensive/ selective self-test can be run. U nless otherwise specified, [...]

16 INFO MODE T est Mode - S elf T est F rom TEST MODE , press the R4 soft key to access the “Self T est” screen (F igure 15). F rom the “Self T est” screen: - L1 soft key initiates a comprehensive self test. The oven will check the door switches, blo wers, magnetrons, and heaters in sequence. - L2 soft key initiates a door switch test only [...]

INFO MODE 17 Serial Number Edit P ress the L4 soft key to access the “Edit Serial N umber” scr een. T o edit the serial number: - U se the number/letter keys to change a character . After one second, the cursor will advance to the next character . - P ress the R3 soft key to advance to the next character . - P ress the L3 soft key to return to [...]

18 INFO MODE Updating the Sof tware F rom the Oven Off scr een, 1. Insert the smart card (see F igure 21). If multiple smart cards are r equired, ensure the correct smart card is loaded first. 2. F rom the COOLING DO WN or OVEN OFF mode, press and hold the Info key until the oven r esets (approximately 5 seconds). 3. When the oven beeps one long hi[...]

Edit Mode[...]

EDIT MODE 19 Over view of the Edit Mode The EDIT MODE serves three main purposes: 1. T o edit set temperatures. 2. T o edit names of food groups and recipes. 3. T o edit recipe settings. T o access the EDIT MODE , 1. Enable it from the “Options ” screen (page 14). 2. P ress the On/Off key to r eturn the oven to the “Cooling Do wn ” or “Of[...]

20 EDIT MODE Changing Set T emperatures If a menu was loaded via smart card or USB (page 17), the temperatures are alr eady set - they need not be changed. The set temperature should never be changed during normal operation. Changing the set temperatures is not advised to compensate for over-cooking or under-cooking situations. Rather , consult you[...]

EDIT MODE 21 Changing Recipe Settings Recipe settings consist of the follo wing: - U p to eight “ events ” or stages of the cook cycle. - Cook time. T o change recipe settings, 1. Place the ov en in EDIT MODE (see page 14). 2. Access the “F ood Group ” screen (page 20). 3. Select a recipe to edit (F igure 24). 4. U se the Down key to mo ve [...]

22 EDIT MODE This page intentionally left blank .[...]

O ven S yst ems[...]

OVEN SYSTEMS 23 Con vection System The convection system is designed to rapidly heat, clean, and recirculate air into the cook cavity . This section contains information about the following components: - Blower motor (bottom) - Blower motor (top) - Blower motor contr oller - Heater element - J etplate (bottom) - J etplate (top) - S tirrer motor and[...]

T roubleshooting Con vection System The following faults may occur in relation to the convection system: - F1: Blower (see page 39) - F2: Low T emp (see page 40) - F6: EC T emp (see page 43) - F7: Thermo (see page 43) - F8: Heat Lo w (see page 44) The following cooking performance issues may occur in relation to the convection system: - F ood not b[...]

OVEN SYSTEMS 25 F igure 26A: P roperly Adjusted Door - Side Views Oven Door Oven Fr ame Hinge SM Switches Remove Bolts Oven Door Hinge P Switch Oven Fr ame F igure 26B: Door Misaligned Variation 1 - Side Views T ap in this corner F igure 26C: Door Misaligned Variation 2 - Side Views T ap in this corner Remove Bolts F irst remove switches, then tap [...]

26 OVEN SYSTEMS Interlock Switches The primary , secondary , and monitor interlock switches engage and disengage in sequence to ensure a proper seal. When the door is opened, the switch sequence is P , S, M. S ubsequently , the sequence is M, S, P when the door is closed. Adjusting the Door Swit ches W ARNING: P rocedure requir es work while the ov[...]

OVEN SYSTEMS 27 Measuring RF Leakage for Microwa ve Safety W ARNING: P rocedure requir es work while the oven and water loads ar e hot. As a result, exercise extr eme caution when testing. An RF (microwav e) leakage test must be performed at the conclusion of the following service tasks: - Door remo val, replacement and/or adjustment - W ave guide [...]

28 OVEN SYSTEMS 5. Close the oven door and pr ess the Enter key . The microwav e system will turn on. 6. P osition the microwave survey meter as shown in F igure 28, abo ve. 7. M easure microwave emission ar ound the door , moving the meter sensor at 0.5 inches/second. As microwav e leakage is obser ved mo ving the sensor at 0.5 inches/second, note[...]

OVEN SYSTEMS 29 Microwav e System The i5 oven emplo ys two independent microwave systems (left and right). In the case of an o ver- current situation relativ e to the left system, the F3 fuse will blow . In the case of an over-curr ent situation relative to the right system, the F4 fuse will blow . This section contains information about the follow[...]

30 OVEN SYSTEMS NO TE: The terminals with the orange dot or the orange wire always go to T erminal 3 on US models. T o verify correct wiring (International), measur e the voltage between the taps on FT1 and FT2. The voltage must be 220 V AC (Latin America), 200 V A C ( J apan), or 230 V A C (International). High-V oltage T ransformers High-v oltage[...]

OVEN SYSTEMS 31 When the high-voltage winding starts to go towar d negative, the high-voltage diode becomes non- conducting with the charged high-voltage capacitor in series with the high-voltage winding. When the transformer gets to its negative peak of -2400 VPK, the voltage applied to the filament is negative 4500 volts. The high-voltage diodes [...]

32 OVEN SYSTEMS Magnetrons F igure 30. Magnetr ons supply the RF energy at 2.45 GHz and begin to oscillate when they are supplied with approximately 4.1 kVDC at approximately .350 mA. D uring operation each magnetron will output a nominal 1 kW of pow er . If replacement is r equired, conduct a microwave leakage test (page 27) after installation of [...]

OVEN SYSTEMS 33 Contr ol System This section contains information about the following components: - Control board - Display - Electrical compartment cooling fans - Electrical compartment cooling fan thermostat - Electrical compartment thermocouple - EMI F ilter - F uses - High-limit thermostat - Keypad - Magnetron cooling fans - Magnetron thermosta[...]

34 OVEN SYSTEMS High Limit Thermostat The high limit thermostat is a 250 V AC, 3-pole, manual-reset thermostat with a trip point of 572 º F (300 º C). The thermostat interr upts po wer to the main convection heater in the event of an abnormal condition. Reset the high-limit thermostat by pr essing the reset button (F igure 31). Keypad The keypad [...]

OVEN SYSTEMS 35 Relay - K7 Magnetron C ooling F an The K7 relay is a 240 V AC, 30 amp , double-pole, double-throw , 24 VDC relay coil. I t switches power to the magnetron cooling fans when the magnetron filaments are actuated. P ower is switched off after 4 minutes, 15 seconds. NO TE: The 4:15 timer star ts ov er each time the magnetron filaments a[...]

36 OVEN SYSTEMS F iltering Syst em This section contains information about the following components: - Catalytic converter - Drain pan - Air F ilter - V ent catalyst Catalytic C onverter The catalytic converter , a V OC type catalyst, is located behind the inside cook cavity wall and is responsible for cleaning the recir culating airflow . The cata[...]

T r oubleshooting[...]

TROUBLESHOO TING 37 Over view of T roubleshooting This section contains information on the following: - F ault code descriptions - F ault code troubleshooting - N on-fault code troubleshooting F or information on accessing TEST MODE , see page 15. F or information and illustrations on replacing components, see the appendix. F ault Code Descriptions[...]

38 TROUBLESHOO TING F ault Code and Description When Active Refer to ... Wa r m up Idle Cooking T est Mode F1: Blower Running Status Bad     Pag e 3 9 F2: Cook T emperature Low  Pa ge 4 0 F3: Magnetron Curr ent Low   Pag e 4 1 F4: Door Monitor Defective   Pag e 4 2 F5: Magnetron Over T emperature   Pag e 4 2 F6: EC [...]

TROUBLESHOO TING 39 T roubleshooting: F1: BL OWER (Blower Running Status Bad) NO YES NO YES NO YES NO T o F rom Description Expected Resistance Black Red W inding (A-B) 5.9-7.3 O hms Black White Winding (A-C) 5.9-7.3 Ohms Red White Winding (B-C) 5.9-7.3 Ohms Black, Red, or White G reen Windings to Chassis Open F igure 33: Motor Windings Resistance [...]

40 TROUBLESHOO TING T roubleshooting: F2: L OW TMP (Cook T emperature Lo w) YES Replace the defective heater . (page A-11) Replace the solid state relay . (page A-5) NO YES YES Replace the I/O control board (page A-8). Correct wiring. YES NO Reset and determine why it tripped – excess grease buildup , etc. (F igure 31, page 34) Is either of the h[...]

TROUBLESHOO TING 41 T roubleshooting: F3: MAG CURR (Magnetron Curr ent Low) Replace K6 relay (see pages A-5 through A-6). YES Run test cook cycles to see if fault repeats (page 10). If not, clear faults. Did fault repeat? NO Are the F3 and F4 fuses functioning properly? YES Replace the F3 and/or F4 fuse (see pages A-5 through A-6) and verify the op[...]

42 TROUBLESHOO TING T roubleshooting: F4: MONIT OR (Door Monitor Defective) NO YES Is the F3 or F4 fuse blo wn? YES Disconnect o ven from power supply and then reconnect. The fault should clear . Replace the F3 or F4 fuse (see page A-5 through A-6). NO Are the switches open- ing in the correct sequence (P , S, M)? T o access TEST MODE or for info o[...]

TROUBLESHOO TING 43 NO T roubleshooting: F6: EC TEMP (Electrical Compar tment T emperature High) YES NO Does the o ven have room to ventilate? Required clearances: T op: 16” (406 mm) Sides: 2” (51 mm) Is the o ven in an area of moderate temperature (120ºF (49ºC) or cooler)? YES Are both cooling fans rotating? NO Relocate o ven to cooler area.[...]

44 TROUBLESHOO TING NO YES Replace the control board (page A-8). Correct wiring. NO YES YES T roubleshooting: F8: HEA T L OW YES NO Is the high-limit thermostat tripped? Are both blow er motors moving air? Check in TEST MODE - see page 15. YES Reset (page 34) and determine why it tripped – excess grease buildup , etc. NO See page 39 to troublesho[...]

TROUBLESHOO TING 45 T roubleshooting: No Keypad Input YES NO Replace the keypad (page A-5 through A-6). If the problem persists, replace the control board (page A-8). Is the keypad cable pr operly connected to the control board? Correct wiring. Correct wiring. If wiring is damaged, replace door switch(es) (page A-9 through A-11). Replace the door s[...]

46 TROUBLESHOO TING NO T roubleshooting: No Display – Screen is Blank YES NO Does the keypad beep when a key is pressed? Is wiring fr om the control board to the display OK? Is pin 1 on the J7 connector receiving 5 VDC? (see schematic, page 51) NO YES YES Replace the display (page A-8). NO NO YES Is the po wer supply output 24 VDC? NO YES YES V e[...]

TROUBLESHOO TING 47 NO YES NO NO YES Is the food item in the correct starting state (e.g., frozen, fresh, etc.)? NO Ensure the food item is being properly stored/prepar ed before cooking. YES NO Place the ov en rack in correct position. Is the o ven rack posi- tioned correctly (upper vs. lower position)? YES NO Ensure that the corr ect amount is be[...]

48 TROUBLESHOO TING T roubleshooting: “Read F ail ” Message When L oading Menu S mart Card USB Device Did you use a smart car d or USB device? NO YES NO YES V erify the USB device is securely attached to the USB port on the oven. Replace the car d reader/ USB port (page A-5 through A-6). If the problem persists, replace the control board (page [...]

TROUBLESHOO TING 49 T roubleshooting: “ W rite F ail” Message When Loading Menu S mart Card USB Device Are you trying to write to a smart card or USB device? YES NO YES V erify the USB device is securely attached to the USB port on the oven. Is the connection fr om USB port to control board OK? Ensure the cable connecting the USB port to the co[...]

50 TROUBLESHOO TING T roubleshooting: “Defective Media ” M essage When O ven is Plugged in or Restarted YES NO Does the message prev ent the oven from reaching the “Oven O ff/ Cooling Do wn ” screen? NO Check for microwav e leakage (page 27). If no leakage is found, replace the control board (page A-8). YES Operate the ov en as you would no[...]

O ven Schematic[...]

SP LI C E 1 J1 DEL TA K3 - 7 L1 EMI FIL T E R L1 HX 1 CK T K6 - 7 K4 -A 1 MW 1 C T L1 2 30V A C, 3Ø 4 W I R E INPUT L1 AUX C T BR N GR N BL K BL K L2 L3 L3 HX 2 CT L2 LOA D DI AG RA M F2-1 VO LT S E 4 F3-1 K5 -B 1 K4 -A 1 F1-1 VO LT S E 3 F2-1 F1-1 K5 -B 1 3 80- 415 , 3Ø 5 W I R E INPUT AY A6A N L2 L3 G N 50 A L2 L3 G F3-1 HX2- 2 L1 L3 L2 N BRN B[...]

52 This page intentionally left blank .[...]

Appendix - Replacing O v en C omponents[...]

A-1 APPENDIX - REPLACING OVEN C OMPONENTS T o Replace This... F irst Remove This... Ite m Part Number No Covers (Page A-3) No Covers- Open T op (Page A-5) T op Cover (Page A-7) Left Side Cover (Page A-9) Right Side Cover (Page A-11) Items Obstructing Access Blower Motor (Bottom) I5-9042  EMI Filt er , EMI Fil Brkt Blower Motor ( T op) I5-9040 ?[...]

A-2 APPENDIX - REPLACING OVEN C OMPONENTS T o Replace This... F irst Remove This... Ite m Part Number No Covers (Page A-3) No Covers- Open T op (Page A-5) T op Cover (Page A-7) Left Side Cover (Page A-9) Right Side Cover (Page A-11) Items Obstructing Access Hinge, Guide, Switch Slide , Lower I5-9316   Door , Switches Hinge, Guide, Switch Slid[...]

APPENDIX - REPLACING OVEN C OMPONENTS A-3 Figur e Reference # I tem Description Item Part Number Hardware Description Hardware P art Number(s) 1 Door Assembly* I5-9308 Screw , #8-32 x 3/8, PFH, 100 Deg, SS 102809 (qty 6) 2 Door Gasket I5-9309 None None 3 Door Handle I5-9253 Screw , 1/4-20 x .25 lg, Serrated Hex 102947 (qty 4) 4 Door Skin I5-9109 Sc[...]

APPENDIX - REPLACING OVEN C OMPONENTS F igure A-1: No Cover Remo val Required 5 9 11 8 16 7 6 12 13 10 15 1 2 3 4 Figur e Reference # I tem Description Item Part Number Hardware Description Hardware Part Number(s) 10 Jetplate ( T op) I5-9203 None None 11 Lower F ront Panel i5-9246 None None 12 Rack I5-9168 None None 13 Rack Suppor t I5-9165 Screw ,[...]

APPENDIX - REPLACING OVEN C OMPONENTS A-5 Replacing Items - Opening T op C over Required (F igure A-3) DANGER: Before r eplacing any oven component, ensure the o ven is remo ved from any pow er source. Replacing a component while the o ven is plugged in can result in serious injury or death. CAUTION: B efore remo ving/installing any component, make[...]

A-6 APPENDIX - REPLACING OVEN C OMPONENTS Figur e Reference # Item Description Item Part Number Hardware Description Hardwar e Part Number(s) 1 Cover , T op I5-9243 Screw , #10-32 x 3/8 lg, PFLH, 100 Deg, SS 101401 (qt y 2) 2 F use, F1, 12-amp 100592 None None 3 F use, F2, 12-amp 100592 None None 4 F use, F3, 12-amp 100592 None None 5 F use, F4, 12[...]

APPENDIX - REPLACING OVEN C OMPONENTS A-7 F igure A-4: Removing T op Cover Required Replacing Items - Removing T op Cover Requir ed (Figur es A-4, A-5, A-6) DANGER: Before r eplacing any oven component, ensure the o ven is remo ved from any pow er source. Replacing a component while the o ven is plugged in can result in serious injury or death. CAU[...]

A-8 APPENDIX - REPLACING OVEN C OMPONENTS Figur e Reference # I tem Description Item P art Number Hardware Description Hardware P art Number(s) 1 Capacitor , High-Voltage 100232 None None 2 Capacitor Clamps 100134 Screw , Sh Mtl #8 x 1/2, Serrated PHTRH 101688 (qty 2) 3 Control Board CON-7002 Nut, Keps , Hex, #6-32, Ex t T ooth, Cres 102961 (qty 4)[...]

APPENDIX - REPLACING OVEN C OMPONENTS A-9 Figur e Reference # Item Description Item Part Number Hardware Description Hardware P art Number(s) 1 Blower Motor (top ) I5-9040 Nut, 1/4 - 20, Serr Hex Flange, Plat ed 100906 (qty 4) 2 Blower Motor (bottom) I5-9042 Nut, 1/4 - 20, Serr Hex Flange, Plated 100906 (qty 4) 3 Blower Wheel (top) 103551 None None[...]

A-10 APPENDIX - REPLACING OVEN C OMPONENTS F igure A-7: Removing Left Side Cov er Required F igure A-8: Blower Motor Assembly 1 3 8 6 7 9 12 13 1 8 3 11 5 2 10 2 8 4[...]

APPENDIX - REPLACING OVEN C OMPONENTS A-11 F igure A-9: Removing Right Side Cover Requir ed Figur e Reference # I tem Description Item Part Number Hardware Description Har dware Part Number(s) 1 Catalytic Con verter I5-9066 None None 2 Cover , Right Side I5-9302 Screw , #8, Serr PPHD, Truss, Black Oxide 101691 (qty 5) 3 Heater Assembly I5-9284 Scre[...]

A-12 APPENDIX - REPLACING OVEN C OMPONENTS Figur e Reference # I tem Description Item Part Number Hardware Description Hardware Part Number(s) 1 Hinge, Bracket, Slide, LHS I5-9196 Nut, Keps, Hex, #8-32, Ext T ooth, Cres 102962 (qty 4) 2 Hinge, Bracket, Slide, RHS I5-9195 Nut, Keps, Hex, #8-32, Ext T ooth, Cres 102962 (qt y 4) 3 Hinge, Cam, Weldment[...]

APPENDIX - REPLACING OVEN C OMPONENTS A-13 F igure A-10: Removing/Opening Multiple Cov ers Required F igure A-11: Counter Balance Assembly , Hinge, and Switch Detail 10 3 4 1 2 14 16 13 15 18 20 17 19 7 8 12 9 11 5 6[...]

F or ser vice or information: WITHIN NOR TH AMERICA CALL C ustomer Service at 800.90 TURBO or OUTSIDE NOR TH AMERICA CALL +1 214-379-6000 or Y our A uthorized Distributor P art Number: i5-9231/Revision B/March 2008 Country Code: NA/EU Accelerating the World of Cooking TM Corporate H eadquar ters Six Concourse Pkwy , S uite 1900 Atlanta, Georgia 303[...]