Français dropdown-ico

Cabletron Systems F3 manuel d'utilisation

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44

Aller à la page of

Les manuels d’utilisation similaires

Un bon manuel d’utilisation

Les règles imposent au revendeur l'obligation de fournir à l'acheteur, avec des marchandises, le manuel d’utilisation Cabletron Systems F3. Le manque du manuel d’utilisation ou les informations incorrectes fournies au consommateur sont à la base d'une plainte pour non-conformité du dispositif avec le contrat. Conformément à la loi, l’inclusion du manuel d’utilisation sous une forme autre que le papier est autorisée, ce qui est souvent utilisé récemment, en incluant la forme graphique ou électronique du manuel Cabletron Systems F3 ou les vidéos d'instruction pour les utilisateurs. La condition est son caractère lisible et compréhensible.

Qu'est ce que le manuel d’utilisation?

Le mot vient du latin "Instructio", à savoir organiser. Ainsi, le manuel d’utilisation Cabletron Systems F3 décrit les étapes de la procédure. Le but du manuel d’utilisation est d’instruire, de faciliter le démarrage, l'utilisation de l'équipement ou l'exécution des actions spécifiques. Le manuel d’utilisation est une collection d'informations sur l'objet/service, une indice.

Malheureusement, peu d'utilisateurs prennent le temps de lire le manuel d’utilisation, et un bon manuel permet non seulement d’apprendre à connaître un certain nombre de fonctionnalités supplémentaires du dispositif acheté, mais aussi éviter la majorité des défaillances.

Donc, ce qui devrait contenir le manuel parfait?

Tout d'abord, le manuel d’utilisation Cabletron Systems F3 devrait contenir:
- informations sur les caractéristiques techniques du dispositif Cabletron Systems F3
- nom du fabricant et année de fabrication Cabletron Systems F3
- instructions d'utilisation, de réglage et d’entretien de l'équipement Cabletron Systems F3
- signes de sécurité et attestations confirmant la conformité avec les normes pertinentes

Pourquoi nous ne lisons pas les manuels d’utilisation?

Habituellement, cela est dû au manque de temps et de certitude quant à la fonctionnalité spécifique de l'équipement acheté. Malheureusement, la connexion et le démarrage Cabletron Systems F3 ne suffisent pas. Le manuel d’utilisation contient un certain nombre de lignes directrices concernant les fonctionnalités spécifiques, la sécurité, les méthodes d'entretien (même les moyens qui doivent être utilisés), les défauts possibles Cabletron Systems F3 et les moyens de résoudre des problèmes communs lors de l'utilisation. Enfin, le manuel contient les coordonnées du service Cabletron Systems en l'absence de l'efficacité des solutions proposées. Actuellement, les manuels d’utilisation sous la forme d'animations intéressantes et de vidéos pédagogiques qui sont meilleurs que la brochure, sont très populaires. Ce type de manuel permet à l'utilisateur de voir toute la vidéo d'instruction sans sauter les spécifications et les descriptions techniques compliquées Cabletron Systems F3, comme c’est le cas pour la version papier.

Pourquoi lire le manuel d’utilisation?

Tout d'abord, il contient la réponse sur la structure, les possibilités du dispositif Cabletron Systems F3, l'utilisation de divers accessoires et une gamme d'informations pour profiter pleinement de toutes les fonctionnalités et commodités.

Après un achat réussi de l’équipement/dispositif, prenez un moment pour vous familiariser avec toutes les parties du manuel d'utilisation Cabletron Systems F3. À l'heure actuelle, ils sont soigneusement préparés et traduits pour qu'ils soient non seulement compréhensibles pour les utilisateurs, mais pour qu’ils remplissent leur fonction de base de l'information et d’aide.

Table des matières du manuel d’utilisation

  • Page 1

    FOT-F3 FIBER OPTIC TRANSCEIVER USER’S MANUAL[...]

  • Page 2

    [...]

  • Page 3

    FOT-F3 USER’S MANUAL i NO TICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice. The reader should in all cases consult Cabletron Systems to determine whether any such changes have been made. The hardware, firmware, or software described in this manual is [...]

  • Page 4

    ii FOT-F3 USER’S MANUAL FCC NO TICE This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested[...]

  • Page 5

    FOT-F3 USER’S MANUAL iii VCCI NO TICE This equipment is in the 1st Class Category (information equipment to be used in commercial and/or industrial areas) and conforms to the standards set by the Voluntary Control Council for Interference by Information Technology Equipment (VCCI) aimed at preventing radio interference in commercial and/or indust[...]

  • Page 6

    iv FOT-F3 USER’S MANUAL DECLARATION OF CONFORMITY Application of Council Directi ve(s): 89/336/EEC 73/23/EEC Manufacturer’ s Name: Cabletron Systems, Inc. Manufacturer’ s Address: 35 Industrial W ay PO Box 5005 Rochester , NH 03867 European Representativ e Name: Mr . J. Solari European Representativ e Address: Cabletron Systems Limited Nexus [...]

  • Page 7

    FOT-F3 USER’S MANUAL v CONTENTS CHAPTER 1 INTRODUCTION 1.1 USING THIS MANUAL ...............................................................1-1 1.2 CONVENTIONS .........................................................................1-2 1.3 OVERVIEW OF THE FOT-F3 ....................................................1-2 1.3.1 Connections ..........[...]

  • Page 8

    CONTENTS vi FOT-F3 USER’S MANUAL CHAPTER 4 TESTING AND TROUBLESHOOTING 4.1 INSTALLATION CHECK-OUT ................................................... 4-1 4.1.1 Testing the Fiber Optic Link Segment ........................ 4-1 4.1.2 Testing the FOT-F3 Fiber Optic Transceiver ............. 4-3 4.2 USING LANVIEW .....................................[...]

  • Page 9

    FOT-F3 USER’S MANUAL 1-1 CHAPTER 1 INTRODUCTION Welcome to Cabletron Systems FOT-F3 Fiber Optic Transceiver User’s Manual . This manual serves as a simple installation and reference guide for the FOT-F3 transceiver. You should have a general working knowledge of Ethernet or IEEE 802.3 type data communications networks and their physical layer c[...]

  • Page 10

    CHAPTER 1: INTRODUCTION 1-2 FOT-F3 USER’S MANUAL Chapter 4, T esting and T roubleshooting , contains procedures for verifying the proper installation of the FOT-F3. It also describes LANVIEW LEDs and their function. Appendix A, Specifications , provides the specifications for the FOT-F3 transceiver. 1.2 CONVENTIONS The following conventions are u[...]

  • Page 11

    OVERVIEW OF THE FOT-F3 FOT-F3 USER’S MANUAL 1-3 Figure 1-1 FOT-F3 1.3.1 Connections The FOT-F3 connects two active Ethernet devices using an AUI cable and a fiber optic link segment. Devices such as repeaters, multiport repeaters, multiport transceivers or host systems are connected using fiber optic cables. The FOT-F3 is fully compatible with IE[...]

  • Page 12

    CHAPTER 1: INTRODUCTION 1-4 FOT-F3 USER’S MANUAL A fiber optic cable is connected to the transceiver through ST fiber optic ports on the FOT-F3. This provides an optical link to connect the device to the network. 1.3.2 Distance and Cable T ype The FOT-F3 supports single mode fiber optic cable for sizes such as 8.3/125 µ m, 8.7/125 µ m, 9/125 µ[...]

  • Page 13

    OVERVIEW OF THE FOT-F3 FOT-F3 USER’S MANUAL 1-5 The SQE test signal is generated after the FOT-F3 has transmitted a data packet. This signal is generated only between the FOT-F3 and the device; it is not transmitted onto the network. Note: Do not enable the SQE test feature when the FOT-F3 is attached to a repeater or Ethernet Version 1 equipment[...]

  • Page 14

    CHAPTER 1: INTRODUCTION 1-6 FOT-F3 USER’S MANUAL PWR (Power) When on, this green LED indicates that the FOT-F3 is receiving power. SQE (Signal Quality Error) Test Function When on, this yellow LED indicates that SQE is enabled. XMT (Transmit) This green LED flashes to indicate that the FOT-F3 is transmitting frames onto the network. RCV (Receive)[...]

  • Page 15

    OVERVIEW OF THE FOT-F3 FOT-F3 USER’S MANUAL 1-7 1.3.4 Application The FOT-F3 can be configured into your network in many ways. For example, in Figure 1-3, a fiber optic link segment (4) is attached to a Cabletron Systems Multi Media Access Center (MMAC) (5) with a FOMIM-32/36/38. The MMAC serves as an intelligent repeater hub that links the fiber[...]

  • Page 16

    CHAPTER 1: INTRODUCTION 1-8 FOT-F3 USER’S MANUAL In another example, shown in Figure 1-4, a FOT-F3 (3) is connected to an MMAC (1) by an AUI cable (2) attached to an Intelligent Repeater Module (IRM) in the MMAC. A lengthy fiber optic link segment (4) of up to five kilometers runs from the FOT-F3 (3) to another FOT-F3 (5). The hardware connection[...]

  • Page 17

    GETTING HELP FOT-F3 USER’S MANUAL 1-9 1.4 GETTING HELP If you need additional support related to this device, or if you have any questions, comments, or suggestions concerning this manual, contact Cabletron Systems Technical Support: By phone (603) 332-9400 Monday – Friday; 8 A.M . – 8 P.M . Eastern Time By CompuServe GO CTRON from any ! prom[...]

  • Page 18

    CHAPTER 1: INTRODUCTION 1-10 FOT-F3 USER’S MANUAL • The device history (i.e., have you returned the device before, is this a recurring problem, etc.) • Any previous Return Material Authorization (RMA) numbers 1.5 RELATED MANUALS Use the manuals identified below to supplement the procedures and other technical data provided in this manual. The[...]

  • Page 19

    FOT-F3 USER’S MANUAL 2-1 CHAPTER 2 INST ALLA TION REQUIREMENTS Before installing the FOT-F3 Fiber Optic Transceiver, all conditions, guidelines, specifications, and requirements included in this chapter and Appendix A must be met to ensure satisfactory performance from the FOT-F3. Failure to follow these guidelines may result in unsatisfactory ne[...]

  • Page 20

    CHAPTER 2: INSTALLATION REQUIREMENTS 2-2 FOT-F3 USER’S MANUAL • When determining the maximum fiber optic cable length, the fiber optic budget and total netw or k propagation dela y should be calculated and taken into consider ation before fiber runs are incor porated into any network design. Fiber optic budget is the combination of the optic[...]

  • Page 21

    FOT-F3 USER’S MANUAL 3-1 CHAPTER 3 INST ALLA TION This chapter contains instructions for unpacking the FOT-F3 Transceiver, connecting the FOT-F3 to an Ethernet device and the network, surface mounting the transceiver (if necessary), and cable support installation. Verify that all the requirements listed in Chapter 2, Installation Requirements , a[...]

  • Page 22

    CHAPTER 3: INSTALLATION 3-2 FOT-F3 USER’S MANUAL If you notice any discrepancies, contact Cabletron Systems Technical Support immediately. Refer to Chapter 1, Getting Help , for instructions. 3.2 CONNECTING THE FOT-F3 TO THE NETWORK After you are sure that all the requirements listed in Chapter 2, Installation Requirements , and Appendix A, Speci[...]

  • Page 23

    CONNECTING THE FOT-F3 TO THE NETWORK FOT-F3 USER’S MANUAL 3-3 Figure 3-1 SQE Switch 3.2.2 Connecting the A UI Cable To connect your Ethernet device to the FOT-F3, attach an AUI cable as follows. See Figure 3-2. 1. Attach an A UI cable to the de vice to which the FO T -F3 will be connected. O T -F3 SQE P W R S Q E X M T R C V C L N L N K TX SQE SW[...]

  • Page 24

    CHAPTER 3: INSTALLATION 3-4 FOT-F3 USER’S MANUAL 2. Attach the f emale connector on the A UI cable to the A UI por t on the FO T -F3. If the power is on f or the Ether net de vice, the PWR LED should be lit, indicating the transceiv er is receiving power from the de vice. Also, if the SQE test is enabled, the SQE LED should be lit. Figure 3-2 AUI[...]

  • Page 25

    CONNECTING THE FOT-F3 TO THE NETWORK FOT-F3 USER’S MANUAL 3-5 c. Disconnect the device to which the transceiver is attached. d. Check the AUI connections for proper pinouts. The pinouts for the transceiver connection are listed in Appendix A. e. Check the cable for continuity. f. Reconnect the AUI cable to the FOT-F3 and the device. 3. Mov e the [...]

  • Page 26

    CHAPTER 3: INSTALLATION 3-6 FOT-F3 USER’S MANUAL ST connectors attach to ST ports much like BNC connectors attach to BNC ports. See Figure 3-3. The connector is inserted into the port with an alignment key on the connector inserted into the alignment slot on the port. The connector is then turned to lock it down. Caution: Do not touch the ends of[...]

  • Page 27

    CONNECTING THE FOT-F3 TO THE NETWORK FOT-F3 USER’S MANUAL 3-7 Figure 3-3 ST Connectors 6. Check that the LNK LED on the FO T -F3 is on. If the LED is off , perform each of the follo wing steps until the LED is on: a. Check that the power is on for the device at the other end of the link. b. Verify that the fiber strands are properly connected to [...]

  • Page 28

    CHAPTER 3: INSTALLATION 3-8 FOT-F3 USER’S MANUAL If a link is not established, contact Cabletron Systems Technical Support. Refer to Chapter 1, Getting Help , for instructions. 3.3 SURFACE MOUNTING THE FOT-F3 Using the contents of the accessory package, you can mount the FOT-F3 on a surface close to the workstation or on the workstation itself. T[...]

  • Page 29

    CABLE SUPPORT INSTALLATION FOT-F3 USER’S MANUAL 3-9 3.4 CABLE SUPPORT INSTALLATION Relieve the strain from the cables attached to the FOT-F3, whether or not the transceiver is mounted to a surface such as a wall. Note: Be sure each cable is securely attached to its port and that the slide latch on the AUI connector is secured to the lock posts on[...]

  • Page 30

    CHAPTER 3: INSTALLATION 3-10 FOT-F3 USER’S MANUAL Figure 3-4 Surface Mounting the FOT-F3 3.4.2 Cable Strain Relief f or Non-Mounted FO T -F3 To relieve the strain to cables connected to a FOT-F3 that is not surface mounted, proceed as follows: 1. If possible , use long tie wraps to secure the FO T -F3 to a structural suppor t such as a beam or a [...]

  • Page 31

    CABLE SUPPORT INSTALLATION FOT-F3 USER’S MANUAL 3-11 The FOT-F3 is now ready for operation. We recommend that you test the system prior to transmitting data. Refer to Chapter 4, Testing And Troubleshooting , for information about how to test the system.[...]

  • Page 32

    CHAPTER 3: INSTALLATION 3-12 FOT-F3 USER’S MANUAL[...]

  • Page 33

    FOT-F3 USER’S MANUAL 4-1 CHAPTER 4 TESTING AND TROUBLESHOO TING This chapter lists procedures to test the FOT-F3 after it is connected to the network. A description of LANVIEW and its function in troubleshooting physical layer network problems is also provided. 4.1 INSTALLATION CHECK-OUT This section contains procedures to test the following • [...]

  • Page 34

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-2 FOT-F3 USER’S MANUAL 4. F ollowing the instructions for the test set, test the jumpers to get a ref erence lev el. Make a note of this reading. 5. Disconnect the jumpers from the barrel connector . 6. Using the jumper , attach the optical power meter to one end of one strand of the link segment. 7. Using[...]

  • Page 35

    INSTALLATION CHECK-OUT FOT-F3 USER’S MANUAL 4-3 4.1.2 T esting the FO T -F3 Fiber Optic T ransceiver T wo Ethernet node testers capable of generating v alid data pack ets, such as the LAN-MD , are required for this procedure . Refer to Figure 4-1 and proceed as follows: 1. Using an AUI cable (2), connect a LAN-MD (1) to the FOT-F3 (3). Figure 4-1[...]

  • Page 36

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-4 FOT-F3 USER’S MANUAL 2. Using another A UI cable (6), connect the other LAN-MD (7) to another FO T -F3 (5) attached to the same fiber optic link segment as the FO T -F3. 3. Select and run test 6 - SER VER on the LAN-MD connected in step 1. V er ify that this test passes. • The status on the LAN-MD sho[...]

  • Page 37

    USING LANVIEW FOT-F3 USER’S MANUAL 4-5 Figure 4-2 shows the location of the LANVIEW LEDs on the FOT-F3. This is followed by a description of how to interpret the indications of these LANVIEW LEDs. Figure 4-2 LANVIEW LEDs Optical Link OK (LNK) LED When on, this green LED indicates that a link has been established between the receive circuitry of t[...]

  • Page 38

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-6 FOT-F3 USER’S MANUAL Receive (RCV) LED This yellow LED flashes to indicate that the transceiver is receiving a frame from the network. The flash of the LED is pulse stretched for easy viewing. The LED flashes when traffic is on the network, even if the data is not intended for the device attached to the [...]

  • Page 39

    USING LANVIEW FOT-F3 USER’S MANUAL 4-7 Power (PWR) LED When on, this green LED indicates that the transceiver is receiving power from the device connected to the FOT-F3 AUI port. If this LED is off, power is not being received from the device or the DC-to-DC converter in the transceiver has failed.[...]

  • Page 40

    CHAPTER 4: TESTING AND TROUBLESHOOTING 4-8 FOT-F3 USER’S MANUAL[...]

  • Page 41

    FOT-F3 USER’S MANUAL A-1 APPENDIX A SPECIFICA TIONS This appendix contains the operational specifications for the FOT-F3. A.1 FIBER OPTIC INTERFACE The FOT-F3 has ST fiber optic ports. Table A-1 lists the parameters along with the associated typical, and minimum/ maximum specifications. Table A-1 Fiber Optic Interface Specifications Parameter Typ[...]

  • Page 42

    APPENDIX A: SPECIFICATIONS A-2 FOT-F3 USER’S MANUAL Parameter Typical Minimum Maximum Receive Sensitivity: -31.0 dBm -36.0 dBm -30.0 dBm Max. Receive Input Power: — — -14.0 dBm Transmitter Power at 25 ° C Into 8.3/125 µ m fiber: -18.0 dBm -21.0 dBm -15.0 dBm Output Power Coefficient: -0.07 dB/ ° C— — Notes: Transmitter Power decreases [...]

  • Page 43

    AUI CONNECTOR FOT-F3 USER’S MANUAL A-3 A.2 AUI CONNECTOR The AUI connector is a male DB15 receptacle with a metal shell for cable shielding. Refer to Figure A-1 for pinout identification. Figure A-1 AUI Connector Pinout Identification A.3 POWER SUPPLY Table A-2 provides the specifications of the power supply in the FOT-F3. Table A-2 Power Supply [...]

  • Page 44

    APPENDIX A: SPECIFICATIONS A-4 FOT-F3 USER’S MANUAL A.4 ENVIRONMENTAL Table A-3 provides the FOT-F3 environmental specifications. A.5 AGENCY APPROVALS Safety The FOT-F3 meets the safety requirements of UL1950, CSA C22.2 No. 950, EN 60950, and 73/23/EEC. Electromagnetic Compatibility The FOT-F3 meets the EMC requirements of FCC Part 15 Class A, EN[...]