Ford 2000 Crown Victoria manuel d'utilisation

Before driving Introduction 2 Instrumentation 6 Controls and features 24 Seating and safety restraints 91 Starting and driving Starting 1 17 Driving 121 Roadside emergencies 136 Servicing Maintenance and care 153 Capacities and specifications 200 Customer assistance 206 Reporting safety defects 217 Index 218 All rights reserved. Reproduction by any[...]

The following warning may be required by California law: CALIFORNIA Proposition 65 W arning Engine exhaust, some if its constituents, and certain vehicle components contain or emit chemicals known to the State of California to cause cancer , or birth defects or other reproductive harm. ICONS Indicates a safety alert. Read the following section on W[...]

W ARNINGS W arnings provide information which may reduce the risk of personal injury and prevent possible damage to others, your vehicle and its equipment. BREAKING-IN YOUR VEHICLE There are no particular breaking-in rules for your vehicle. During the first 1 600 km (1 000 miles) of driving, vary speeds frequently . This is necessary to give the mo[...]

These are some of the symbols you may see on your vehicle. V ehicle Symbol Glossary Safety Alert See Owner’ s Guide Fasten Safety Belt Air Bag-Front Air Bag-Side Child Seat Child Seat Installation W arning Child Seat T ether Anchorage Brake System Anti-Lock Brake System Brake Fluid - Non-Petroleum Based T raction Control Master Lighting Switch Ha[...]

V ehicle Symbol Glossary Child Safety Door Lock/Unlock Interior Luggage Compartment Release Symbol Panic Alarm Engine Oil Engine Coolant Engine Coolant T emperature Do Not Open When Hot Battery A void Smoking, Flames, or Sparks Battery Acid Explosive Gas Fan W arning Power Steering Fluid Maintain Correct Fluid Level MAX MIN Emission System Engine A[...]

R.DEF . AUTO LAMP 0FF PANEL DIM PUSH INTERIOR HI LO F E CHECK ENGINE AIR SUSP OD OFF BRAKE TEMP VOLTS FUEL MPH km/h 10 20 30 40 50 60 70 80 90 10 0 11 0 12 0 20 40 60 80 100 120 140 160 180 200 H C F H L < FUEL FILL DOOR P R N D 2 1 OFF ON Driver air bag (pg. 105) Instrument cluster (pg. 8) Rear window defroster control (pg. 25) Instrument panel[...]

SCAN BASS TREB BAL FADE SIDE EJ REW FF 1 - 2 TAPE AMS VOL - PUSH ON SEEK TUNE AM FM CLK 12 3 456 FM1 ST L NORM A/C VENT FLOOR FLR • DEF DEF HI LO MAX A/C OUTSIDE TEMP AUTOMATIC OFF F AUTO HM OIL H L RSM SET ACC COAST Electronic sound system (pg. 35) Climate control systems (pg. 26) Clock (pg. 34) T raction control switch* (pg. 123) Gearshift with[...]

W ARNING LIGHTS AND CHIMES Standard instrument cluster Optional instrument cluster Low fuel (if equipped) Illuminates as an early reminder of a low fuel condition indicated on the fuel gauge (refer to Fuel gauge in this chapter for more information). When refueling, after the light comes on, the amount of fuel that is added will be less than the ad[...]

Check engine Y our vehicle is equipped with a computer that monitors the engine’ s emission control system. This system is commonly known as the On Board Diagnostics System (OBD II). This OBD II system protects the environment by ensuring that your vehicle continues to meet government emission standards. The OBD II system also assists the service[...]

Light is blinking: Engine misfire is occurring which could damage your catalytic converter . Y ou should drive in a moderate fashion (avoid heavy acceleration and deceleration) and have your vehicle serviced at the first available opportunity . Under engine misfire conditions, excessive exhaust temperatures could damage the catalytic converter , th[...]

Brake system warning • Standard instrument cluster • Optional instrument cluster Momentarily illuminates when the ignition is turned to the ON position. Also illuminates if the parking brake is engaged. If brake warning lamp does not illuminate at these times, seek service immediately . Illumination after releasing the parking brake indicates l[...]

Charging system Illuminates when the ignition is turned to the ON position and the engine is off. The light also illuminates when the battery is not charging properly , requiring electrical system service. Engine oil pressure (if equipped) Illuminates when the oil pressure falls below the normal range. Stop the vehicle as soon as safely possible an[...]

O/D off • Standard instrument cluster • Optional instrument cluster Illuminates when the T ransmission Control Switch (TCS), refer to Overdrive control in the Controls and Features chapter , has been pushed turning the transmission overdrive function OFF . When the light is on, the transmission does not operate in the overdrive mode, refer to t[...]

Door ajar Illuminates when one of the doors is not completely shut and the ignition is turned to ON. W ith the ignition ON, this light will flash five times and sound a tone for one second, then remain on (if a door is open). Low washer fluid Momentarily illuminates when the ignition is turned to ON and will stay on when the windshield washer fluid[...]

Headlamps on warning chime Sounds when the headlamps or parking lamps are on, the ignition is off (and the key is not in the ignition) and the driver’ s door is opened. GAUGES Standard instrument cluster gauges Optional instrument cluster gauges Fuel gauge Displays approximately how much fuel is in the fuel tank (when the key is in the ON positio[...]

• Standard instrument cluster • Optional instrument cluster A minimum of four gallons must be added or removed from the fuel tank in order for the gauge to instantaneously update. If less than four gallons is added, the gauge will take between five to ten minutes to update. Speedometer Indicates the current vehicle speed. • Standard instrumen[...]

• Optional instrument cluster Odometer Registers the total kilometers (miles) of the vehicle. • Standard instrument cluster • Optional instrument cluster Refer to Electronic Message Center for information on how to switch the display from metric to English measurements. km / h MPH km S MPH km/h 10 20 30 40 50 60 70 80 90 10 0 11 0 12 0 20 40 [...]

T rip odometer Registers the kilometers (miles) of individual journeys. T o reset, depress the control. Refer to Electronic Message Center for T rip A and T rip B features on the optional instrument cluster . Engine coolant temperature gauge Indicates the temperature of the engine coolant. At normal operating temperature, the needle remains within [...]

• Optional instrument cluster This gauge indicates the temperature of the engine coolant, not the coolant level. If the coolant is not at its proper level the gauge indication will not be accurate. If the gauge enters the red section, the engine coolant and Check Engine/Service Engine Soon indicators illuminate, refer to What you should know abou[...]

Add oil if needed (refer to Engine oil in the Maintenance and care chapter). If the oil level is correct, have your vehicle checked at your dealership or by a qualified technician. ELECTRONIC MESSAGE CENTER The electronic message center only works when the ignition is in the ON position. The message center allows you to: • see problems such as do[...]

E/M Press this control to switch the electronic instrument cluster display and the message center display from metric to English units. Select Each press of the SELECT control will select a different function. Press the right side of the control to advance the function to the right, and press the left side of the control to advance the function to [...]

Remember to turn the ignition OFF when refueling your vehicle. Otherwise, the display will not show the addition of fuel for a few miles. At least four gallons of fuel must be added for the fuel gauge to immediately show the new fuel level. The DTE function will flash for 5 seconds and sound a tone for 1 second when you have approximately: • 80 k[...]

Press the RESET control while A VG ECON is displayed to reset the function. The average displayed is the average since the last reset. TRIP A and TRIP B These two functions allow you to see how far you have traveled since you last reset. T rip A and T rip B are completely independent and must be reset individually . T o reset either trip feature to[...]

P ANEL DIMMER CONTROL Use to adjust the brightness of the instrument panel during headlight and parklamp operation. • Push up to brighten. • Push down to dim. HEADLAMP CONTROL Rotate the headlamp control to the first position to turn on the parking lamps. Rotate to the second position to also turn on the headlamps. T o turn on the interior lamp[...]

High beams Push forward to activate. Pull toward you to deactivate. Flash to pass Pull toward you to activate and release to deactivate. AUTOLAMP CONTROL (IF EQUIPPED) The autolamp system provides light sensitive automatic on-off control of the exterior lights normally controlled by the headlamp control. The autolamp system also keeps the lights on[...]

Press the rear defroster control to clear the rear window of thin ice and fog. • A small LED will illuminate when the rear defroster is activated. The ignition must be in the ON position to operate the rear window defroster . The defroster turns off automatically after 10 minutes or when the ignition is turned to the OFF position. T o manually tu[...]

Since the air conditioner removes considerable moisture from the air during operation, it is normal if clear water drips on the ground under the air conditioner drain while the system is working and even after you have stopped the vehicle. • MAX A/C-Uses recirculated air to cool the vehicle. MAX A/C is noisier than NORM A/C but more economical an[...]

• T o prevent humidity buildup inside the vehicle, do not drive with the climate control system in the OFF or MAX A/C position. • Do not put objects under the front seat that will interfere with the airflow to the back seats. • Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield). • If your vehicle has [...]

Turning the EA TC on Press AUTOMA TIC, any of the override controls or the fan speed control. The EA TC will only operate when the vehicle is running. Turning the EA TC off Press OFF . The Outside T emperature function will continue to operate until the ignition is turned off. Automatic operation Press AUTOMA TIC and select the desired temperature.[...]

T o control the temperature, select any temperature between 18°C (65°F) and 29°C (85°F) by pressing the blue (cooler) or red (warmer) buttons. For continuous maximum cooling, push the blue button until 16°C (60°F) is shown in the display window . The EA TC will continue maximum cooling (disregarding the displayed temperature) until a warmer t[...]

Fan speed ( ) When AUTOMA TIC is pressed, fan speed is adjusted automatically for existing conditions. Y ou can override fan speed at any time. T o control fan speed manually , use the thumbwheel to cancel automatic fan speed operation. Rotate the thumbwheel up for higher fan speed or down for lower fan speed. The display will show to indicate manu[...]

economical and will cool the inside of the vehicle faster . Airflow is from the instrument panel registers. This mode can also be used to prevent undesirable odors from entering the vehicle. • NORM A/C-Uses outside air to cool the vehicle. The temperature display will remain the same and air will be cooled based on the selected temperature. It is[...]

Displaying outside temperature Press OUTSIDE TEMP to display the outside air temperature. It will be displayed until OUTSIDE TEMP is pressed again. If the selected temperature is changed while the outside temperature is displayed, the new temperature will be displayed for four seconds after it is changed, then the outside temperature will return to[...]

• Remove any snow , ice or leaves from the air intake area (at the bottom of the windshield). • If your vehicle has been parked with the windows closed during hot weather , the air conditioner will do a much faster job of cooling if you drive for two or three minutes with the windows open. This will force most of the hot, stale air out of the v[...]

USING YOUR AUDIO SYSTEM AM/FM Stereo V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. 1 2 3 4 AM/FM SEEK TONE CLK TUNE TONE VOL 12 FM ST DX VOL PUSH ON VOL PUSH ON VOL PUSH ON Controls and features 35[...]

If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio mode. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the control to [...]

Radio station memory preset The radio is equipped with four station memory preset controls. These controls can be used to select up to four preset AM stations and eight FM stations (four in FM1 and four in FM2). Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to T une adjust or S[...]

Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Press the TONE control three times, then use the volume knob to adjust the desired level. Speaker fade adjust (if equipped) Speaker sound can be adjusted between the front and rear speakers. Press the TONE control four times, then use the volume k[...]

V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in [...]

Tune adjust The tune control works in radio mode. Tune adjust in radio mode • Press to move to the next frequency down the band (whether or not a listenable station is located there). Hold the control to move through the frequencies quickly . • Press to move to the next frequency up the band (whether or not a listenable station is located there[...]

Setting memory preset stations 1. Select the frequency band with the AM or the FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Bass adjus[...]

Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. T ape select • T o enter tape mode while in radio mode, press the T APE AMS control. Automatic Music Search The Automatic Music Search feature allows you to q[...]

selection). The tape deck stops and returns to play mode when the AMS circuit senses a blank section on the tape. In order to ensure proper operation of the AMS feature, the tape MUST have a blank section of at least four seconds duration between programs. Rewind The rewind control works in tape mode. T o rewind in tape mode, press the REW control.[...]

Setting the clock Y our vehicle is equipped with a separate instrument panel mounted clock. Please refer to Clock in this chapter for instructions on setting the clock. AM/FM Stereo / Single CD Radio V olume/power control Press the control to turn the audio system on or off. T urn the control to raise or lower volume. BASS CD TREB BAL FADE SCN CLK [...]

If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio and CD modes. AM/FM select in radio mode This control allows you to select AM or FM frequency bands. Press the con[...]

Seek function The seek function control works in radio, CD or CD changer mode (if equipped). Seek function in radio mode • Press to find the next listenable station down the frequency band. • Press to find the next listenable station up the frequency band. Seek function in CD or CD changer mode (if equipped) • Press to listen to the next sele[...]

Setting memory preset stations 1. Select the frequency band with the AM/FM select control. 2. Select a station. Refer to T une adjust or Seek function for more information on selecting a station. 3. Press and hold a memory preset control until the sound returns, indicating the station is held in memory on the control you selected. Bass adjust The b[...]

Speaker balance adjust Speaker sound distribution can be adjusted between the right and left speakers. Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. CD select • T o begin CD play (if CD[s] are loaded), press the CD control. The first track of the disc will begin playing. After that, CD play will begin wher[...]

Fast forward The fast forward control works in CD mode. T o fast forward in CD changer mode, press the CD control (preset 2). Press the control again to deactivate fast forward mode. Eject function Press the control to stop and eject a CD. Compression feature Compression adjust brings soft and loud CD passages together for a more consistent listeni[...]

Premium AM/FM Stereo/Cassette (CD Changer Compatible) Y our audio system is equipped with selective lighting, a unique lighting strategy . This lighting feature is operable when the headlamps are illuminated. During the operation of any selected mode, lighting for the individual function controls will either illuminate or turn off. Those controls w[...]

T urn the control to raise or lower volume. If the volume is set above a certain level and the ignition is turned off, the volume will come back on at a “nominal” listening level when the ignition switch is turned back on. AM/FM select The AM/FM select control works in radio, tape and CD modes (if equipped). AM/FM select in radio mode This cont[...]

disc unless the CD changer is in shuffle mode.) Refer to Shuffle feature for more information. Hold the control to continue reversing through the discs. • Press to select the next disc in the CD changer . Hold the control to fast-forward through the remaining discs. Seek function The seek function control works in radio, tape or CD mode (if equip[...]

Scan function in radio mode Press the SCAN control to hear a brief sampling of all listenable stations on the frequency band. Press the SCAN control again to stop the scan mode. Scan function in tape mode Press the SCAN control to hear a short sampling of all selections on the tape. (The tape scans in a forward direction. At the end of the tape’ [...]

Starting autoset memory preset 1. Select a frequency using the AM/FM select controls. 2. Press the AUTO control. 3. When the first six strong stations are filled, the station stored in memory preset control 1 will start playing. If there are less than six strong stations available on the frequency band, the remaining memory preset controls will all[...]

Speaker fade adjust Speaker sound can be adjusted between the front and rear speakers. Press the F ADE control. Use the SEL control to adjust the sound between the front and rear speakers. T ape/CD select • T o begin tape play (with a tape loaded into the audio system) while in the radio or CD mode, press the T APE control. Press the button durin[...]

• In CD mode, pressing the control for less than three seconds results in slow forward action. Pressing the control for more than three seconds results in fast forward action. T ape direction select Press SIDE 1–2 to play the alternate side of a tape. Eject function Press the control to stop and eject a tape. Dolby T noise reduction Dolby t noi[...]

shuffle feature continues to the next disc after all tracks are played. Press the SHUFFLE control to start this feature. Random order play will continue until the SHUFFLE control is pressed again. Mute mode Press the control to mute the playing media. Press the control again to return to the playing media. Radio data system (RDS) feature This featu[...]

• Use the SEL control to select the program type. W ith the feature on, use the SEEK or SCAN control to find the desired program type from the following selections: • Classic • Country • Info • Jazz • Oldies • R&B • Religious • Rock • Soft • To p 4 0 Show • W ith RDS activated, press the RDS control until SHOW is display[...]

CD changer (if equipped) The CD changer is located in one of the following locations: • in the trunk • in the center console • under the driver’ s seat 1. Slide the door to access the CD changer magazine. 2. Press to eject the magazine. 3. T urn the magazine (A) over . 4. Using the disc holder release knob (C), pull the disc holder (B) out [...]

If you pull too hard on the disc holder , the disc holder may come completely out of the magazine. If this happens, reinsert the disc holder back into the magazine while pressing on the lever (A). 5. Line up the CD with the groove of the disc holder . Ensure that the label on the CD faces downwards. 6. Press in on the disc holder until it locks sec[...]

The CD magazine may be inserted or ejected with the radio power off. ONL Y use the magazine supplied with the CD changer , other types will damage the unit. Keep the CD changer door closed. Coins and foreign objects will damage the CD player and void your audio system warranty . Do not insert any promotional (odd shaped or sized) discs, or discs wi[...]

• Do not insert more than one disc into each slot of the CD changer magazine. Cleaning cassette player (if equipped) Clean the tape player head with a cassette cleaning cartridge after 10 to 12 hours of play in order to maintain the best sound and operation. Cassette and cassette player care • Use only cassettes that are 90 minutes long or less[...]

• Station overload. W eak signals are sometimes captured by stronger signals when you pass a broadcast tower . A stronger signal may temporarily overtake a weaker signal and play while the weak station frequency is displayed. The audio system automatically switches to single channel reception if it will improve the reception of a station normally[...]

POSITIONS OF THE IGNITION 1. ACCESSORY , allows the electrical accessories such as the radio to operate while the engine is not running. 2. LOCK, locks the steering wheel, automatic transmission gearshift lever and allows key removal. 3. OFF , shuts off the engine and all accessories without locking the steering wheel. 4. ON, all electrical circuit[...]

OVERDRIVE CONTROL Activating overdrive (Overdrive) is the normal drive position for the best fuel economy . The overdrive function allows automatic upshifts and downshifts through all available gears. Deactivating overdrive Press the T ransmission Control Switch (TCS) located on the end of the gearshift lever . The T ransmission Control Indicator L[...]

Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved. Do not shift the gearshift lever into N (Neutral) with the speed control on. T o turn speed control off • Press OFF or • T urn off the vehicle ignition. Once speed control is switched off, the previously programmed set speed will be erased. T o se[...]

If your vehicle slows down more than 16 km/h (10 mph) below your set speed on an uphill, your speed control will disengage. This is normal. Pressing RES/RSM/RESUME will re-engage it. Do not use the speed control in heavy traffic or on roads that are winding, slippery , or unpaved. T o set a higher set speed • Press and hold SET/SET ACC/ SET ACCEL[...]

• Depress the brake pedal. When the desired vehicle speed is reached, press SET/SET ACC/ SET ACCEL. T o disengage speed control • Depress the brake pedal. Disengaging the speed control will not erase the previously programmed set speed. Pressing OFF will erase the previously programmed set speed. COAST RESUME SET ACCEL OFF ON Controls and featu[...]

T o return to a previously set speed • Press RES/RSM/RESUME. For RES/RSM/RESUME to operate, the vehicle speed must be faster than 48 km/h (30 mph). Indicator light (if equipped) This light comes on when either the SET ACC/SET ACCEL or RES/RSM/ RESUME controls are pressed. It turns off when the speed control OFF control is pressed, the brake is ap[...]

Programming 1. Prepare for programming the HomeLink t Universal T ransceiver by erasing the three factory default codes by holding down the two outside buttons until the red light begins to flash after 20 seconds. Release both buttons. 2. Hold the end of your hand-held transmitter 5–14 cm (2–5 inches) away from the HomeLink t Universal T ransce[...]

T o program your hand-held transmitters: • continue to hold the button on the HomeLink t Universal T ransceiver . • press and re-press the hand-held transmitter button every two seconds until the red light changes from a slow to a fast flash. Operating the HomeLink T Universal T ransceiver Once programmed, the HomeLink t Universal T ransceiver [...]

3. Press and release the programmed HomeLink t button. Press and release the HomeLink t button a second time to complete the training process. (Some garage door openers may require this procedure to be done a third time to complete the training). The 2nd or 3rd press from step 3 will activate the door . The HomeLink t Universal T ransceiver has now[...]

AUTOMATIC DIMMING INSIDE REAR VIEW MIRROR (IF EQUIPPED) Y our vehicle is equipped with an inside rear view mirror which has an auto-dimming function. The electronic day/night mirror will change from the normal state to the non-glare state when bright lights (glare) reach the mirror . When the mirror detects bright light from front or behind, it wil[...]

Compass zone adjustment 1. Determine which compass zone you are in by referring to the zone map. 2. W ith the compass display turned on, press and hold the COMP side of the control for no more than six seconds until the zone selection number appears in the mirror display window . If a “C” appears repeat this step. 3. Release the COMP side of th[...]

2. Press and hold the COMP side of the control for approximately six seconds until “C” appears in the mirror display . 3. Drive the vehicle slowly (less than 5 km/h [3 mph]) in circles or on your everyday routine until the display reads a direction. 4. The compass is now calibrated. T RUNK REMOTE CONTROL The remote trunk release control is loca[...]

• Press the bottom portion of the rocker switch to open. Express down • Press AUTO and release quickly . The window will open fully . Depress again to stop window operation. Window lock The window lock feature allows only the driver to operate the power windows. T o lock out all the window controls except for the driver’ s press the left side[...]

POWER DOOR LOCKS Press U to unlock all doors and L to lock all doors. Smart locks W ith the key in the ignition, in any switch position, and either the driver’ s or passenger’ s door open, the doors cannot be locked using the front door lock switches. While the key is in the ignition, the vehicle can be locked by manually pressing the lock cont[...]

2. Move the control in the direction you wish to tilt the mirror . 3. Return to the center position to lock mirrors in place. CHILDPROOF DOOR LOCKS When these locks are set, the rear doors cannot be opened from the inside. The rear doors can be opened from the outside when the doors are unlocked. The childproof locks are located on rear edge of eac[...]

REMOTE ENTRY SYSTEM (IF EQUIPPED) The remote entry system allows you to lock or unlock all vehicle doors without a key . The remote entry features only operate with the ignition in the OFF position. If there is any potential remote keyless entry problem with your vehicle, ensure ALL key fobs (remote entry transmitters) are brought to the dealership[...]

Y ou must complete steps 1-7 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. 1. T urn the ignition key to ON. 2. Press the power door unlock control on the door panel three times. 3. T urn the ignition key from ON to OFF . 4. Press the power door unlock control three time[...]

Automatic door locks can be turned on/off with the keyless entry keypad through the following procedure: Y ou must complete steps 1-5 within 30 seconds or the procedure will have to be repeated. If the procedure needs to be repeated, you must wait 30 seconds. 1. Enter the keyless entry keypad factory code. 2. W ithin 5 seconds, press and hold contr[...]

Opening the trunk Press the control once to open the trunk. Ensure that the trunk is closed and latched before driving your vehicle. Failure to latch the trunk may cause objects to fall out of the trunk or block the rear view . Sounding a panic alarm Press this control to activate the alarm. T o deactivate the alarm, press the control again or turn[...]

The inside lights will not turn off if: • they have been turned on with the dimmer control or • any door is open. The battery saver will shut off the interior lamps 30 minutes after the last door is closed or after 10 minutes if the door is left open. Replacing the battery The remote transmitter is powered by one coin type three-volt lithium ba[...]

Replacing lost transmitters T ake all your vehicle’ s transmitters to your dealer if service is required. If you purchase additional transmitters (up to four may be programmed into memory), perform the following procedure: T o reprogram the transmitters yourself, place the key in the ignition and turn from OFF to ON four times in rapid succession[...]

and devices cannot damage the P A TS ignition key , but can cause a momentary concern if they are too close to the key during engine start. If a problem occurs, turn ignition OFF and restart the engine with all other objects on the key ring held away from the ignition key . Check to make sure the encoded ignition key is an approved Ford encoded ign[...]

Y ou will need to have two previously programmed coded keys and the new unprogrammed SecuriLock y key readily accessible for timely implementation of each step in the procedure. Please read and understand the entire procedure before you begin. 1. Insert the first previously programmed coded key into the ignition and turn the ignition from OFF to ON[...]

See also Remote entry system in this chapter for more information. Y our vehicle has a factory-set 5–digit code that operates the keyless entry system. Y ou can also program your own 5–digit personal entry code. The factory-set code is located: • on the owner’ s wallet card in the glove compartment • taped to the computer module When pres[...]

Erasing personal code T o erase all of the personal entry codes programmed to a vehicle: 1. Enter the factory-set code. 2. Press 1/2 within 5 seconds of step 1. 3. Press and hold 1/2 for two seconds. All of the vehicle doors will lock and then unlock to confirm erasure. Unlocking the doors and releasing the trunk with the keyless entry system T o u[...]

Locking doors with the keyless entry system It is not necessary to enter the factory-set code prior to locking all doors. T o lock the doors: Press 7/8 and 9/0 at the same time. INTERIOR LUGGAGE COMPARTMENT RELEASE (IF EQUIPPED) Y our vehicle is equipped with a mechanical interior luggage compartment release handle that provides a means of escape f[...]

Keep vehicle doors and luggage compartment locked and keep keys out of a child’ s reach. Unsupervised children could lock themselves in an open trunk and risk injury . Children should be taught not to play in vehicles. On hot days, the temperature in the trunk or vehicle interior can rise very quickly . Exposure of people or animals to these high[...]

SEA TING Head restraints Y our vehicle’ s seats may be equipped with head restraints which are vertically adjustable. The purpose of these head restraints is to help limit head motion in the event of a rear collision. T o properly adjust your head restraints, lift the head restraint so that it is located directly behind your head or as close to t[...]

Lift handle to move seat forward or backward. Pull lever up to adjust seatback. Using the manual recline function (if equipped) Never adjust the driver’ s seat or seatback when the vehicle is moving. Do not pile cargo higher than the seatbacks to avoid injuring people in a collision or sudden stop. Always drive and ride with your seatback upright[...]

T o adjust the front seatback using the manual recliner: • Lift and hold the handle located on the side of the seat. • Lean against the seatback to adjust it to your desired position. Y ou can recline the seat back or bring it forward. • Release the handle when the desired position has been reached. Adjusting the power front seats – door mo[...]

Press to move the seat forward or backward. Press to move the front portion of the seat cushion up or down. Press to move the rear portion of the seat cushion up or down. Adjusting the power seats – seat mounted controls Never adjust the driver’ s seat or seatback when the vehicle is moving. Always drive and ride with your seatback upright and [...]

Reclining the seatback can reduce the effectiveness of the seat’ s safety belt in the event of a collision. The power seat controls are located on the side of the driver’ s seat. Press to raise or lower the seat, or to move the seat forward or backward. Using the power lumbar support (if equipped) The power lumbar control is located on the outb[...]

All occupants of the vehicle, including the driver , should always properly wear their safety belts, even when an air bag SRS is provided. It is extremely dangerous to ride in a cargo area, inside or outside of a vehicle. In a collision, people riding in these areas are more likely to be seriously injured or killed. Do not allow people to ride in a[...]

2. T o unfasten, push the release button and remove the tongue from the buckle. The front and rear outboard safety restraints in the vehicle are combination lap and shoulder belts. The front passenger and rear seat outboard safety belts have two types of locking modes described below: V ehicle sensitive mode The vehicle sensitive mode is the normal[...]

How to use the automatic locking mode • Buckle the combination lap and shoulder belt. • Grasp the shoulder portion and pull downward until the entire belt is extracted. • Allow the belt to retract. As the belt retracts, you will hear a clicking sound. This indicates the safety belt is now in the automatic locking mode. How to disengage the au[...]

Front safety belt height adjustment Y our vehicle has safety belt height adjustments for the driver and front passenger . Adjust the height of the shoulder belt so the belt rests across the middle of your shoulder . T o lower the shoulder belt height, push the button and slide the height adjuster down. T o raise the height of the shoulder belt, sli[...]

Insert the tongue into the correct buckle (the buckle closest to the direction the tongue is coming from). T o lengthen the belt, turn the tongue at a right angle to the belt and pull across your lap until it reaches the buckle. T o tighten the belt, pull the loose end of the belt through the tongue until it fits snugly across the hips. Shorten and[...]

Conditions of operation If... Then... The driver’ s safety belt is not buckled before the ignition switch is turned to the ON position... The safety belt warning light illuminates1-2 minutes and the warning chime sounds 4-8 seconds. The driver’ s safety belt is buckled while the indicator light is illuminated and the warning chime is sounding..[...]

The following are reasons most often given for not wearing safety belts: (All statistics based on U.S. data) Reasons given... Consider ... 9 Crashes are rare events 9 36 700 crashes occur every day . The more we drive, the more we are exposed to 9 rare 9 events, even for good drivers. 1 in 4 of us will be seriously injured in a crash during our lif[...]

One time disable Anytime the safety belt is buckled and then unbuckled during an ignition ON cycle, Belt Minder will be disabled for that ignition cycle only . Deactivating/activating the belt minder feature Read step s1-9 thoroughly before proceeding with the deactivation/ activation programming procedure. The Belt Minder feature can be deactivate[...]

6. W ithin seven seconds of the safety belt warning light turning off, buckle then unbuckle the safety belt. • This will disable Belt Minder if it is currently enabled, or enable Belt Minder if it is currently disabled. 7. Confirmation of disabling Belt Minder is provided by flashing the safety belt warning light four times per second for three s[...]

AIR BAG SUPPLEMENT AL RESTRAINT SYSTEM (SRS) Y our vehicle is equipped with a crash sensing and diagnostic module which records information about the air bag and sensor systems. In the event of a collision this module may save information related to the collision including information about the air bag system and impact severity . This information [...]

Always transport children 12 years old and under in the back seat and always properly use appropriate child restraints. National Highway T raffic Safety Administration (NHTSA) recommends a minimum distance of at least 25 cm (10 inches) between an occupant’ s chest and the driver air bag module. Never place your arm over the air bag module as a de[...]

Children and air bags For additional important safety information, read all information on safety restraints in this guide. Children must always be properly restrained. Accident statistics suggest that children are safer when properly restrained in the rear seating positions than in the front seating position. Failure to follow these instructions m[...]

The air bags inflate and deflate rapidly upon activation. After air bag deployment, it is normal to notice a smoke-like, powdery residue or smell the burnt propellant. This may consist of cornstarch, talcum powder (to lubricate the bag) or sodium compounds (e.g., baking soda) that result from the combustion process that inflates the air bag. Small [...]

• and the electrical wiring which connects the components. The diagnostic module monitors its own internal circuits and the supplemental air bag electrical system warning (including the impact sensors), the system wiring, the air bag system readiness light, the air bag back up power and the air bag ignitors. Determining if the system is operation[...]

Important child restraint precautions Y ou are required by law to use safety restraints for children in the U.S. and Canada. If small children ride in your vehicle (generally children who are four years old or younger and who weigh 18 kg [40 lbs] or less), you must put them in safety seats made especially for children. Check your local and state or[...]

A belt-positioning booster should be used if the shoulder belt rests in front of the child’ s face or neck, or if the lap belt does not fit snugly on both thighs, or if the thighs are too short to let the child sit all the way back on the seat cushion when the lower legs hang over the edge of the seat cushion. Y ou may wish to discuss the special[...]

• Keep the buckle release button pointing up and away from the safety seat, with the tongue between the child seat and the release button, to prevent accidental unbuckling. • Place seat back in upright position. • Put the safety belt in the automatic locking mode. Refer to Automatic locking mode (passenger side front and outboard rear seating[...]

2. Pull down on the shoulder belt and then grasp the shoulder belt and lap belt together . 3. While holding the shoulder and lap belt portions together , route the tongue through the child seat according to the child seat manufacturer’ s instructions. Be sure the belt webbing is not twisted. 4. Insert the belt tongue into the proper buckle (the b[...]

5. T o put the retractor in the automatic locking mode, grasp the shoulder portion of the belt and pull downward until all of the belt is extracted and a click is heard. 6. Allow the belt to retract. The belt will click as it retracts to indicate it is in the automatic locking mode. 7. Pull the lap belt portion across the child seat toward the buck[...]

Installing child safety seats in the lap belt seating positions 1. Lengthen the lap belt. T o lengthen the belt, hold the tongue so that its bottom is perpendicular to the direction of webbing while sliding the tongue up the webbing. 2. Place the child safety seat in the center seating position. 3. Route the tongue and webbing through the child sea[...]

1. Position the child safety seat on the passenger seat cushion. 2. Route the child safety seat tether strap over the back of the seat. For vehicles with adjustable head restraints, route the tether strap under the head restraint and between the head restraint posts, otherwise route the tether strap over the top of the seatback. 3. Locate the corre[...]

PREPARING TO START YOUR VEHICLE Engine starting is controlled by the powertrain control system. This system meets all Canadian Interference-Causing Equipment standard requirements regulating the impulse electrical field strength of radio noise. When starting a fuel-injected engine, avoid pressing the accelerator before or during starting. Only use [...]

3. Make sure the parking brake is set. 4. Make sure the gearshift is in P (Park). 5. T urn the key to 4 (ON) without turning the key to 5 (ST ART). If there is difficulty in turning the key , firmly rotate the steering wheel left and right until the key turns freely . This condition may occur when: • front wheels are turned • front wheel is aga[...]

ST ARTING THE ENGINE 1. T urn the key to 5 (ST ART) without pressing the accelerator pedal and release as soon as the engine starts. The key will return to 4 (ON). 2. If the temperature is above –12°C (10°F) and the engine does not start within five seconds on the first try , turn the key to OFF , wait 10 seconds and try again. 3. If the temper[...]

Guarding against exhaust fumes Although odorless and colorless, carbon monoxide is present in exhaust fumes. T ake precautions to avoid its dangerous effects. If you ever smell exhaust fumes of any kind inside your vehicle, have your dealer inspect and fix your vehicle immediately . Do not drive if you smell exhaust fumes. These fumes are harmful a[...]

BRAKES Y our service brakes are self-adjusting. Refer to the scheduled maintenance guide for scheduled maintenance. Occasional brake noise is normal and often does not indicate a performance concern with the vehicle’ s brake system. In normal operation, automotive brake systems may emit occasional or intermittent squeal or groan noises when the b[...]

ABS warning lamp ABS The ABS warning lamp in the instrument cluster momentarily illuminates when the ignition is turned to the ON position. If the light does not illuminate momentarily at start up, remains on or continues to flash, the ABS needs to be serviced. W ith the ABS light on, the anti-lock brake system is disabled and normal braking is sti[...]

The BRAKE warning lamp in the instrument cluster illuminates and remains illuminated (when the ignition is turned ON) until the parking brake is fully released. Always set the parking brake fully and make sure the gearshift is latched in P (Park). T urn off the ignition whenever you leave your vehicle. The parking brake is not recommended to stop a[...]

The system operates by detecting and controlling wheel spin. The system borrows many of the electronic and mechanical elements already present in the anti-lock braking system (ABS). Wheel-speed sensors allow excess rear wheel spin to be detected by the T raction Control y portion of the ABS computer . Any excessive wheel spin is controlled by autom[...]

The T raction Control y system will be on every time you turn the ignition key from OFF to ON until you deactivate the system using the traction control switch in the glove compartment. STEERING Y our vehicle is equipped with power steering. Power steering uses energy from the engine to help steer the vehicle. T o prevent damage to the power steeri[...]

This system keeps the rear of your vehicle at a constant level by automatically adding air or releasing air from the springs. If you exceed the load limit, the rear air suspension may not operate. The air suspension shut-off switch is located on the left side of the trunk. If this switch is in the OFF position, the rear air suspension will not oper[...]

If your vehicle gets stuck in mud or snow it may be rocked out by shifting from forward and reverse gears, stopping between shifts, in a steady pattern. Press lightly on the accelerator in each gear . Do not rock the vehicle if the engine is not at normal operating temperature or damage to the transmission may occur . Do not rock the vehicle for mo[...]

R (Reverse) W ith the gearshift lever in R (Reverse), the vehicle will move backward. Always come to a complete stop before shifting into and out of R (Reverse). N (Neutral) W ith the gearshift lever in N (Neutral), the vehicle can be started and is free to roll. Hold the brake pedal down while in this gear . Overdrive The normal driving position f[...]

Each time the vehicle is started, the transmission will automatically return to normal Overdrive mode. Every time the vehicle is shut off and restarted, you must press the transmission control switch to cancel overdrive operation if the Overdrive mode is not desired. 2 (Second) Use 2 (Second) to start-up on slippery roads or to provide additional e[...]

• Payload: Combined maximum allowable weight of cargo, passengers and optional equipment. The payload equals the gross vehicle weight rating minus base curb weight. • GVW (Gross V ehicle W eight): Base curb weight plus payload weight. The GVW is not a limit or a specification. • GVWR (Gross V ehicle W eight Rating): Maximum total weight of th[...]

limitations. Replacement tires with a higher limit than the originals do not increase the GVWR and GA WR limitations. The Certification Label, found on the inside pillar of the driver’ s door , lists several important vehicle weight rating limitations. Before adding any additional equipment, refer to these limitations. If you are adding weight to[...]

Preparing to tow Use the proper equipment for towing a trailer , and make sure it is properly attached to your vehicle. See your dealer or a reliable trailer dealer if you require assistance. Hitches Do not use hitches that clamp onto the vehicle bumper . Use a load carrying hitch. Y ou must distribute the load in your trailer so that 10% of the to[...]

• Consult your local motor vehicle speed regulations for towing a trailer . • Use a lower gear when towing up or down steep hills. This will eliminate excessive downshifting and upshifting for optimum fuel economy and transmission cooling. • Anticipate stops and brake gradually . Exceeding the GCWR rating may cause internal transmission damag[...]

Replace the rear axle lubricant anytime the axle has been submerged in water . Rear axle lubricant quantities are not to be checked or changed unless a leak is suspected or repair required. Disconnect the wiring to the trailer before backing the trailer into the water . Reconnect the wiring to the trailer after the trailer is removed from the water[...]

DRIVING THROUGH WATER Do not drive quickly through standing water , especially if the depth is unknown. T raction or brake capability may be limited and if the ignition system gets wet, your engine may stall. W ater may also enter your engine’ s air intake and severely damage your engine. If driving through deep or standing water is unavoidable, [...]

GETTING ROADSIDE ASSIST ANCE T o fully assist you should you have a vehicle concern, Ford offers a complimentary roadside assistance program. This program is separate from the New V ehicle Limited W arranty . The service is available: • 24–hours, seven days a week • for the Basic warranty period (Canada) or New V ehicle Limited W arranty peri[...]

Roadside coverage beyond basic warranty In the United States, you may purchase additional roadside assistance coverage beyond this period through the Ford Auto Club by contacting your Ford or Lincoln Mercury dealer . HAZARD FLASHER Use only in an emergency to warn traffic of vehicle breakdown, approaching danger , etc. The hazard flashers can be op[...]

The fuel pump shut-off switch is located on the left side of the trunk behind the trunk liner . Use the following procedure to reset the fuel pump shut-off switch. 1. T urn the ignition to the OFF position. 2. Check the fuel system for leaks. 3. If no fuel leak is apparent, reset the fuel pump shut-off switch by pushing in on the reset button. 4. T[...]

Always replace a fuse with one that has the specified amperage rating. Using a fuse with a higher amperage rating can cause severe wire damage and could start a fire. Standard fuse amperage rating and color COLOR Fuse Rating Mini Fuses Standard Fuses Maxi Fuses Cartridge Maxi Fuses Fuse Link Cartridge 2A Grey Grey — — — 3A Violet Violet — ?[...]

The fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 1 15A Brake Pedal Position (BPP) Switch, Multi-Function Switch, Speed Control 2 30A W iper Control Module, W indshield W iper Motor 3 — Not Used 4 15A Lighting Control Module, Main Light Switch 5 15A Backup Lamps, V ariable Assist Powe[...]

Fuse/Relay Location Fuse Amp Rating Passenger Compartment Fuse Panel Description 9 30A Blower Motor , A/C-Heater Mode Switch 10 10A Air Bag Module 11 5A Radio 12 18A CB Lighting Control Module, Flash-to-Pass, Main Light Switch 13 15A W arning Lamps, Analog Cluster Gauges and Indicators, Electronic Automatic T ransmission, Lighting Control Module 14[...]

The high-current fuses are coded as follows. Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 1 20A* Electric Fuel Pump Relay 2 30A* Generator , Starter Relay , Fuses 15 and 18 3 25A* Radio, CD Changer , Subwoofer Amplifier 4 30A* Police Power Relay 5 15A* Horn Relay 6 20A* DRL Module 7 20A CB Power door Locks, Power Seats, T [...]

Fuse/Relay Location Fuse Amp Rating Power Distribution Box Description 12 30A** PCM Power Relay , PCM, Natural Gas V ehicle Module 13 50A** High Speed Cooling Fan Relay 14 40A** Rear W indow Defrost Relay , Also see Fuse 17 15 50A** Anti-Lock Brake Module 16 50A** Police Option Fuse Holder 17 30A CB Cooling Fan Relay Relay 1 — Rear Defrost Relay [...]

When driving with the temporary spare tire do not: • exceed 80 km/h (50 mph) under any circumstances • load the vehicle beyond maximum vehicle load rating listed on the Safety Compliance Label • tow a trailer • use tire chains • drive through an automatic car wash, because of the vehicle’ s reduced ground clearance • try to repair the[...]

5. Loosen each wheel lug nut one-half turn counterclockwise but do not remove them until the wheel is raised off the ground. Refer to Anti-theft lug nuts for information on removing anti-theft lug nuts. On vehicles equipped with Air Suspension, turn OFF the Air Suspension switch prior to jacking, hoisting or towing your vehicle. Refer to Air suspen[...]

T o lessen the risk of personal injury , do not put any part of your body under the vehicle while changing a tire. Do not start the engine when your vehicle is on the jack. The jack is only meant for changing the tire. • Never use the rear differential as a jacking point. 8. Remove the lug nuts with the lug wrench. 9. Replace the flat tire with t[...]

T o remove the anti-theft lug nut: 1. Insert the key over the locking lug nut. Make sure you hold the key square to the lug nut. If you hold the key at an angle, you could damage the key and the lug nut. 2. Place the lug nut wrench over the lug nut key and apply pressure on the key with the wrench. 3. T urn the wrench in a counterclockwise directio[...]

3. Park the booster vehicle close to the hood of the disabled vehicle making sure the two vehicles do not touch. Set the parking brake on both vehicles and stay clear of the engine cooling fan and other moving parts. 4. Check all battery terminals and remove any excessive corrosion before you attach the battery cables. Ensure that vent caps are tig[...]

3. Connect the negative (-) cable to the negative (-) terminal of the assisting battery . 4. Make the final connection of the negative (-) cable to an exposed metal part of the stalled vehicle’ s engine, away from the battery and the carburetor/fuel injection system. Do not use fuel lines, engine rocker covers or the intake manifold as grounding [...]

Jump starting 1. Start the engine of the booster vehicle and run the engine at moderately increased speed. 2. Start the engine of the disabled vehicle. 3. Once the disabled vehicle has been started, run both engines for an additional three minutes before disconnecting the jumper cables. Removing the jumper cables Remove the jumper cables in the rev[...]

3. Remove the jumper cable from the positive (+) terminal of the booster vehicle’ s battery . 4. Remove the jumper cable from the positive (+) terminal of the disabled vehicle’ s battery . After the disabled vehicle has been started and the jumper cables removed, allow it to idle for several minutes so the engine computer can relearn its idle c[...]

WRECKER TOWING If you need to have your vehicle towed, contact a professional towing service or , if you are a member , your roadside assistance center . It is recommended that your vehicle be towed with a wheel lift or flatbed equipment. Do not tow with a slingbelt. Ford Motor Company has not approved a slingbelt towing procedure. Before your vehi[...]

SERVICE RECOMMENDATIONS T o help you service your vehicle: • W e highlight do-it-yourself items in the engine compartment for easy location. • W e provide a Scheduled Maintenance Guide which makes tracking routine service easy . If your vehicle requires professional service, your dealership can provide necessary parts and service. Check your ?[...]

Working with the engine off 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. T urn off the engine and remove the key . 3. Block the wheels to prevent the vehicle from moving unexpectedly . Working with the engine on 1. Set the parking brake and ensure the gearshift is securely latched in P (Park). 2. Block the w[...]

IDENTIFYING COMPONENTS IN THE ENGINE COMPARTMENT 4.6L SOHC V8 engine 1. Brake fluid reservoir 2. Engine oil dipstick 3. Engine oil filler cap 4. W indshield washer fluid reservoir 5. Air filter assembly 6. Power steering fluid reservoir 7. Engine coolant reservoir 8. Battery 9. Automatic transmission fluid dipstick 9 1 2 3 6 5 7 8 4 Maintenance and[...]

ENGINE OIL Checking the engine oil Refer to the Scheduled Maintenance Guide for the appropriate intervals for checking the engine oil. 1. Make sure the vehicle is on level ground. 2. T urn the engine off and wait a few minutes for the oil to drain into the oil pan. 3. Set the parking brake and ensure the gearshift is securely latched in P (Park). 4[...]

• If the oil level is within this range, the oil level is acceptable. DO NOT ADD OIL. • If the oil level is below this mark, engine oil must be added to raise the level within the normal operating range. • If required, add engine oil to the engine. Refer to Adding engine oil in this chapter . • Do not overfill the engine with oil. Oil level[...]

engine oil filler cap and use a funnel to pour the engine oil into the opening. 3. Recheck the engine oil level. Make sure the oil level is not above the normal operating range on the engine oil level indicator (dipstick). 4. Install the indicator and ensure it is fully seated. 5. Fully install the engine oil filler cap by turning the filler cap cl[...]

BRAKE FLUID Checking and adding brake fluid Brake fluid should be checked and refilled as needed. Refer to the Scheduled Maintenance Guide for the service interval schedules. 1. Clean the reservoir cap before removal to prevent dirt or water from entering the reservoir . 2. Visually inspect the fluid level. 3. If necessary , add brake fluid from a [...]

WINDSHIELD WASHER FLUID Checking and adding washer fluid Check the washer fluid whenever you stop for fuel. The reservoir is highlighted with a symbol. If the level is low , add enough fluid to fill the reservoir . In very cold weather , do not fill the reservoir all the way . Only use a washer fluid that meets Ford specifications. Refer to Lubrica[...]

• protection against rust and other forms of corrosion. • an accurate temperature readout from the engine coolant gauge. The engine coolant must be maintained at the correct fluid level and concentration to work properly . If the engine coolant fluid level and concentration is not maintained correctly , damage to the engine and cooling system m[...]

• DO NOT USE Ford Extended Life Engine Coolant F6AZ-19544-AA (orange in color). • DO NOT USE a DEX-COOL t engine coolant or an equivalent engine coolant that meets Ford specification WSS-M97B44-D. • DO NOT USE alcohol or methanol antifreeze or any engine coolants mixed with alcohol or methanol antifreeze. • DO NOT USE supplemental coolant a[...]

Have your dealer check the engine cooling system for leaks if you have to add more than 1.0 liter (1.0 quart) of engine coolant per month. T o avoid scalding hot steam or coolant from being released from the engine cooling system, never remove the radiator cap while the engine is running or hot. Failure to follow this warning may result in damage t[...]

Severe climates If you drive in extremely cold climates (less than –36° C [–34° F]): • it may be necessary to increase the coolant concentration above 50%. • NEVER increase the coolant concentration above 60%. • increased engine coolant concentrations above 60% will decrease the overheat protection characteristics of the engine coolant [...]

How fail-safe cooling works • Standard cluster • Optional cluster If the engine begins to overheat: • the engine coolant temperature gauge will move to the H (hot) area (if your vehicle is equipped with analog gauges). • the engine coolant temperature gauge will illuminate all eight bars and a tone will sound every five seconds for one minu[...]

Continued operation will increase the engine temperature: • the symbol will begin to flash. • if your vehicle is equipped with digital gauges, the gauge bars will flash and a tone will sound every five seconds for one minute. • the engine will completely shut down, causing steering and braking effort to increase. Once the engine temperature c[...]

CHECKING AND ADDING POWER STEERING FLUID Check the power steering fluid. Refer to the Scheduled Maintenance Guide for the service interval schedules. If adding fluid is necessary , use only MERCON t AT F . 1. Start the engine and let it run until it reaches normal operating temperature (the engine coolant temperature gauge indicator will be near th[...]

Automatic transmission fluid expands when warmed. T o obtain an accurate fluid check, drive the vehicle until it is at normal operating temperature (approximately 30 km [20 miles]). If your vehicle has been operated for an extended period at high speeds, in city traffic during hot weather or pulling a trailer , the vehicle should be turned off for [...]

The transmission fluid should be in this range if at normal operating temperature (66°C-77°C [150°F-170°F]). The transmission fluid should be in this range if at ambient temperature (10°C-35°C [50°F-95°F]). High fluid level Fluid levels above the safe range may result in transmission failure. An overfill condition of transmission fluid may [...]

BATTERY Y our vehicle is equipped with a Motorcraft maintenance-free battery which normally does not require additional water during its life of service. However , for severe usage or in high temperature climates, check the battery electrolyte level. Refer to the Scheduled Maintenance Guide for the service interval schedules. Keep the electrolyte l[...]

When lifting a plastic-cased battery , excessive pressure on the end walls could cause acid to flow through the vent caps, resulting in personal injury and/or damage to the vehicle or battery . Lift the battery with a battery carrier or with your hands on opposite corners. Keep batteries out of reach of children. Batteries contain sulfuric acid. A [...]

• Always dispose of automotive batteries in a responsible manner . Follow your local authorized standards for disposal. Call your local authorized recycling center to find out more about recycling automotive batteries. AIR FILTER MAINTENANCE Refer to the Scheduled Maintenance Guide for the appropriate intervals for changing the air filter element[...]

6. Install a new air filter element. Be careful not to crimp the filter element edges between the air filter housing and cover . This could cause filter damage and allow unfiltered air to enter the engine if not properly seated. 7. Replace the air filter housing cover and secure the clamps. 8. Replace the air inlet tube and secure the clamp. Failur[...]

T o replace the wiper blades: 1. Pull the wiper arm away from the windshield and lock into the service position. 2. T urn the blade at an angle from the wiper arm. Push the lock pin manually to release the blade and pull the wiper blade down toward the windshield to remove it from the arm. 3. Attach the new wiper to the wiper arm and press it into [...]

T readwear The treadwear grade is a comparative rating based on the wear rate of the tire when tested under controlled conditions on a specified government test course. For example, a tire graded 150 would wear one and one-half (1 1/2) times as well on the government course as a tire graded 100. The relative performance of tires depends upon the ac[...]

SERVICING YOUR TIRES Checking the tire pressure • Use an accurate tire pressure gauge. • Check the tire pressure when tires are cold, after the vehicle has been parked for at least one hour or has been driven less than 5 km (3 miles). • Adjust tire pressure to recommended specifications found on the T ire Pressure label. Improperly inflated t[...]

• Five tire rotation (for vehicles with steel wheels and full size spare tires) Replacing the tires Replace the tires when the wear band is visible through the tire treads. When replacing full size tires, never mix radial bias-belted, or bias-type tires. Use only the tire sizes that are listed on the Certification Label. Make sure that all tires [...]

Failure to follow these precautions may adversely affect the handling of the vehicle and make it easier for the driver to lose control and roll over . T ires that are larger or smaller than your vehicle’ s original tires may also affect the accuracy of your speedometer . SNOW TIRES AND CHAINS Snow tires must be the same size and grade as the tire[...]

The fuel system may be under pressure. If the fuel filler cap is venting vapor or if you hear a hissing sound, wait until it stops before completely removing the fuel filler cap. Otherwise, fuel may spray out and injure you or others. If you do not use the proper fuel filler cap, excessive pressure or vacuum in the fuel tank may damage the fuel sys[...]

• A void getting fuel liquid in your eyes. If fuel is splashed in the eyes, remove contact lenses (if worn), flush with water for 15 minutes and seek medical attention. Failure to seek proper medical attention could lead to permanent injury . • Fuels can also be harmful if absorbed through the skin. If fuel is splashed on the skin and/or clothi[...]

When fueling your vehicle: 1. T urn the engine off. 2. Carefully turn the filler cap counterclockwise 1/8 of a turn until it stops. 3. Pull to remove the cap from the fuel filler pipe. 4. T o install the cap, align the tabs on the cap with the notches on the filler pipe. 5. T urn the filler cap clockwise 1/8 of a turn until it stops. If the “Serv[...]

Octane recommendations Y our vehicle is designed to use “Regular” unleaded gasoline with an (R+M)/2 octane rating of 87. W e do not recommend the use of gasolines labeled as “Regular” that are sold with octane ratings of 86 or lower in high altitude areas. Do not be concerned if your engine sometimes knocks lightly . However , if it knocks [...]

If you have run out of fuel: • Y ou may need to cycle the ignition from OFF to ON several times after refueling, to allow the fuel system to pump the fuel from the tank to the engine. • Y our “Check Engine” indicator may come on. For more information on the “Check Engine” indicator , refer to the Instrumentation chapter . Fuel Filter Fo[...]

For consistent results when filling the fuel tank: • Use the same filling rate setting (low — medium — high) each time the tank is filled. • Allow three automatic click-offs when filling. • Always use fuel with the recommended octane rating. • Use a known quality gasoline, preferably a national brand. • Use the same side of the same p[...]

Habits • Smooth, moderate operation can yield up to 10% savings in fuel. • Steady speeds without stopping will usually give the best fuel economy . • Idling for long periods of time (greater than one minute) may waste fuel. • Anticipate stopping; slowing down may eliminate the need to stop. • Sudden or hard accelerations may reduce fuel e[...]

• Carrying unnecessary weight may reduce fuel economy (approximately 0.4 km/L [1 mpg] is lost for every 180 kg [400 lb] of weight carried). • Adding certain accessories to your vehicle (for example bug deflectors, rollbars/light bars, running boards, ski/luggage racks) may reduce fuel economy . • Using fuel blended with alcohol may lower fuel[...]

The scheduled maintenance items listed in the Scheduled Maintenance Guide are essential to the life and performance of your vehicle and to its emissions system. If other than Ford, Motorcraft or Ford-authorized parts are used for maintenance replacements or for service of components affecting emission control, such non-Ford parts should be equivale[...]

If the vehicle’ s powertrain system or its battery has just been serviced, the on-board diagnostics system is reset to a “not ready for I/M test” condition. T o ready the on-board diagnostics system for I/M testing, a minimum of 30 minutes of city and highway driving is necessary as described below: • First, at least 10 minutes of driving o[...]

3. Disconnect the electrical connector from the bulb by pulling rearward. 4. Remove the bulb retaining ring by rotating it counterclockwise (when viewed from the rear) to free it from the bulb socket, and slide the ring off the plastic base. Keep the ring to retain the new bulb. 5. W ithout turning, remove the old bulb from the lamp assembly by gen[...]

5. T urn the headlamps on and make sure they work properly . If the headlamp was correctly aligned before you changed the bulb, you should not need to align it again. Replacing front parking lamp/turn signal bulbs The park/turn lamp bulbs can be replaced with out removing the headlamp assembly . 1. Make sure headlamp switch is in OFF position, then[...]

1. Open the trunk and carefully pull the carpet away to expose the plastic retainer . 2. Remove plastic retainer to expose the lamp assembly hardware. 3. Remove three nut and washer assemblies and the lamp assembly from the vehicle. 4. Remove the bulb socket by rotating it counterclockwise, then pulling it out of the lamp assembly . 5. Pull the bul[...]

Replacing license plate lamp bulbs 1. Remove two screws, grommets and the license plate lamp assembly from the trunk lid. 2. Carefully pull the bulb from the socket and push in the new bulb. 3. Install the lamp assembly on trunk lid with two grommets, ensuring the grommets are pushed all the way in to the trunk lid and secure with two screws. Repla[...]

Function T rade Number Headlamp 9007 Park lamp and turn lamp (front) 3457 NAK (amber) Side marker (front) 194 NA (amber) Cornering lamp (front) 3156K T ail, stop, turn (rear) 3157 K Side marker (rear) 194 Backup lamp 3156K License plate lamp 168 High-mount brakelamp 912 Luggage compartment lamp 212-2 Dome lamp 906 Rear reading lamp 211-2 Map lamp 1[...]

W ashing your vehicle W ash your vehicle regularly with cold or lukewarm water . Never use strong detergents or soap. If your vehicle is particularly dirty , use a quality car wash detergent. Always use a clean sponge, washing glove or similar device and plenty of water for best results. T o avoid spots, avoid washing when the hood is still warm, i[...]

Repairing paint chips Minor scratches or paint damage from road debris may be repaired with the Ultra T ouch Prep and Finishing Kit (#F7AZ-19K507–BA), Lacquer T ouch-up Paint (#ALBZ-19500–XXXXA), or Exterior Acrylic Spray Lacquer (#ALAZ-19500–XXXXA) from the Ford Car Care Chemicals line. Please note that the part numbers (shown as XXXX above)[...]

T o avoid scratching the lamps, do not use a dry paper towel, chemical solvents or abrasive cleaners. Cleaning the wiper blades, windshield and rear window If the wiper blades do not wipe properly , clean the wiper blade rubber element with undiluted windshield washer solution or a mild detergent. T o avoid damaging the blades, do not use fuel, ker[...]

• Cover the highlighted areas to prevent water damage when cleaning the engine. • Never wash or rinse the engine while it is running; water in the running engine may cause internal damage. Cleaning the instrument panel Clean with a damp cloth, then dry with a dry cloth. A void cleaner or polish that increases the gloss of the upper portion of t[...]

Cleaning the instrument cluster lens Clean with a damp cloth, then dry with a dry cloth. Do not use household or glass cleaners as these may damage the lens. Cleaning seats equipped with side air bags Remove dust and loose dirt with a whisk broom or a vacuum cleaner . Remove fresh spots immediately . Follow the directions that come with the cleaner[...]

Cleaning leather seats (if equipped) T o clean, simply use a soft cloth dampened with water and a mild soap. W ipe the leather again with a damp cloth to remove soap residue. Dry with a soft cloth. For tougher soiling concerns, Ford recommends using the Deluxe Leather Care Kit F8AZ-19G253–AA, which is available from your Ford Dealer . This mild c[...]

MOTORCRAFT PART NUMBERS Component 4.6L SOHC V8 engine Air filter element F A-1668 Fuel filter FG-986B Battery-standard BXT -65–650 Battery-heavy duty BXT -65–750 Oil filter FL-820-S PCV valve EV -98 Spark plugs* A WSF-32P * Refer to V ehicle Emissions Control Information (VECI) decal for spark plug gap information. REFILL CAPACITIES Fluid Ford [...]

2 Ensure the correct automatic transmission fluid is used. MERCON t and MERCON t V are not interchangeable. DO NOT MIX MERCON t and MERCON t V . Refer to the Scheduled Maintenance Guide to determine the correct service interval. 3 Indicates only approximate dry-fill capacity . Some applications may vary based on cooler size and if equipped with an [...]

Item Ford part name Ford part number Ford specification Engine oil Motorcraft SAE 5W -30 Super Premium Motor Oil XO-5W30-QSP WSS-M2C153-G with API Certification Mark Hinges, latches, striker plates, fuel filler door hinge and seat tracks Multi-Purpose Grease DOAZ-19584-AA or F5AZ-19G209-AA ESB-M1C93-B or ESR-M1C159-A Lock cylinders Penetrating and [...]

ENGINE DATA Engine 4.6L V8 engine Cubic inches 281 Required fuel 87 octane Firing order 1-3-7-2-6-5-4-8 Spark plug gap 1.3-1.4 mm (0.052-0.056 inch) Ignition system Coil on plug Compression ratio 10.0:1 VEHICLE DIMENSIONS V ehicle dimensions mm (in) (1) Overall length 5 382 (211.9) (2) Overall width 1 987 (78.2) (3) Overall height 1 443 (56.8) (4) [...]

IDENTIFYING YOUR VEHICLE Certification label The National Highway T raffic Safety Administration Regulations require that a Certification Label be affixed to a vehicle and prescribe where the Certification Label may be located. The Certification Label is located on the front door latch pillar on the driver’ s side. 4 1 MFD. BY FORD MOTOR CO. IN U[...]

V ehicle identification number The vehicle identification number is attached to a metal tag and is located on the driver side instrument panel. (Please note that in the graphic XXXX is representative of your vehicle identification number .) Engine number The engine number (the last eight numbers of the vehicle identification number) is stamped on t[...]

Ford Extended Service Plan Y ou can get more protection for your new car or light truck by purchasing Ford Extended Service Plan (Ford ESP) coverage. Ford ESP is an optional service contract which is backed by Ford Motor Company or Ford Motor Service Company (in the U.S.) and Ford of Canada (in Canada). It provides the following: • benefits durin[...]

If you have questions or concerns, or are unsatisfied with the service you are receiving, follow these steps: 1. Contact your Sales Representative or Service Advisor at your selling/servicing dealership. 2. If your inquiry or concern remains unresolved, contact the Sales Manager or Service Manager at the dealership. 3. If the inquiry or concern can[...]

If you own a Lincoln vehicle and are away from home when your vehicle needs service, or if you need more help than the dealership could provide, after following the steps described above, contact the Ford Customer Assistance Center to find an authorized dealership to help you. In the United States: Ford Motor Company Customer Assistance Center 1680[...]

dispute handling procedure is not required prior to enforcing state created rights or other rights which are independent of the Magnuson-Moss W arranty Act or state replacement or repurchase laws. THE DISPUTE SETTLEMENT BOARD (U.S. ONLY) The Dispute Settlement Board is: • an independent, third-party arbitration program for warranty disputes • a[...]

Eligibility may differ according to state law . For example, see the unique brochures for California, W est Virginia, Georgia and W isconsin purchasers/lessees. Board membership The Board consists of: • three consumer representatives • a Ford or Lincoln Mercury dealership representative Consumer candidates for Board membership are recruited and[...]

• the names (if known) of all the people you contacted at the dealership(s) • a description of the action you expect to resolve your concern Y ou will receive a letter of explanation if your application does not qualify for Board review . Oral presentations If you would like to make an oral presentation, indicate YES to question #6 on the appli[...]

Y ou may also contact the North American Customer Assistance Center at 1-800-392-3673 (Ford), TDD for the hearing impaired: 1-800-232-5952 or by writing to the Center at the following address: Ford Motor Company Customer Assistance Center 16800 Executive Plaza Drive P .O. Box 6248 Dearborn, Michigan 48121 UTILIZING THE MEDIATION/ARBITRATION PROGRAM[...]

The use of leaded fuel in your vehicle without proper conversion may damage the effectiveness of your emission control system and may cause engine knocking or serious engine damage. Ford Motor Company/Ford of Canada is not responsible for any damage caused by use of improper fuel. In the United States, using leaded fuel may also result in difficult[...]

Ford Deluxe Leather and Vinyl Cleaner (not available in Canada) Motorcraft Vinyl Cleaner (Canada only) Ford Extra Strength T ar and Road Oil Remover* (not available in Canada) Ford Extra Strength Upholstery Cleaner (Canada only) Ford Extra Strength Upholstery Cleaner (not available in Canada) Ford Metal Surface Cleaner Ford Multi-Purpose Cleaner* M[...]

Comfort and convenience Cargo nets Engine block heaters T ravel equipment Daytime running lights Heavy-duty battery Protection and appearance equipment Air bag anti-theft locks Carpet floor mats Cleaners, waxes and polishes Flat splash guards Front end covers Lubricants and oils Molded splash guards Molded vinyl floor mats T ouch-up paint Universal[...]

use or are not properly installed. When operated, such systems may cause the engine to stumble or stall. In addition, such systems may be damaged or their performance may be affected by operating your vehicle. (Citizens band [CB] transceivers, garage door openers and other transmitters with outputs of five watts or less will not ordinarily affect y[...]

REPORTING SAFETY DEFECTS (U.S. ONLY) If you believe that your vehicle has a defect that could cause a crash, or could cause injury or death, you should immediately inform the National Highway T raffic Safety Administration (NHTSA) in addition to notifying Ford Motor Company . If NHTSA receives similar complaints, it may open an investigation, and i[...]

Air bag supplemental restraint system ........................ 105 and child safety seats ............ 107 description .............................. 105 disposal .................................... 109 driver air bag .......................... 107 indicator light ....................10,109 operation ................................. 107 passenger[...]

set zone adjustment ................. 74 Controls power seat ............................ 93,94 Coolant checking and adding .............. 160 coolant temperature light ........ 10 refill capacities ................. 163,200 specifications ...................201,203 Cruise control (see Speed control) .................... 65 Customer Assistance ....[...]

quality ...................................... 182 running out of fuel ................. 182 safety information relating to automotive fuels ..................... 178 Fuses ...................................138,139 Garage door opener .................... 69 Gas cap (see Fuel cap) ............ 180 Gas mileage (see Fuel economy) ................. 18[...]

anti-lock brakes (ABS) ..... 11,122 brake .......................................... 11 charging system ........................ 12 check engine ............................... 9 high beam ................................. 11 low coolant ................................ 10 low fuel ........................................ 8 oil pressure ...........[...]

Specification chart, lubricants ............................201,203 Speed control .............................. 65 Speedometer ............................... 16 Starting your vehicle ......... 117,119 jump starting .......................... 147 Steering speed sensitive ....................... 125 Steering wheel tilting ..........................[...]

223[...]

Required fuel Unleaded fuel only - 87 octane Fuel tank capacity 71.9L (19.0 gallons) Engine oil capacity (includes filter change) 4.7L (5.0 quarts). Use Motorcraft SAE 5W -30 Super Premium Motor Oil, Ford specification WSS-M2C153-G. T ire pressure and size Refer to the T ire Pressure Label located on the rear passenger door jamb. Hood release Pull [...]