Philips 170B manuel d'utilisation

Philips 170B Electronic User's Manual file:///D|/Philips LCD/english/170B/Index.htm [1/20/2001 3:16:47 PM][...]

Safety and Troubleshooting Information Safety Precautions and Maintenance • Installation Locations • Correct Handling of the LCD Monitor • FAQs • Troubleshooting • Regulatory Information • Other Related Information Safety precautions and maintenance WARNING: Use of controls, adjustments, or procedures other than those specified in this [...]

Temperature: 5-35°C 41-95°F ❍ Humidity: 20-80% RH ❍ Do not subject the LCD monitor to severe vibration or high impact conditions. Do not place the LCD monitor inside a car trunk. ● Take care not to mishandle this product by either knocking or dropping during operation or transportation. ● Do not store or use the LCD monitor in locations e[...]

When handling the monitor, grip the bottom firmly with both hands and ensure that the front panel faces outward before lifting. Please refer to the diagram on the right. 1. Handling the monitor with care prevents scratching and damage. If the monitor becomes damaged, immediately disconnect the power from the unit and have it checked by a qualified [...]

About This Electronic User's Manual About This Guide • Other Documents You May Need • Notational Descriptions About This Guide This electronic user's guide is intended for anyone who uses the Philips LCD Monitor. It describes the LCD monitor's features, setup, operation and other pertinent information. Its contents are identical [...]

Notes, Cautions, and Warnings Throughout this guide, blocks of text may be accompanied by an icon and printed in bold or italic type. These blocks contain notes, cautions, or warnings. They are used as follows: NOTE: This icon indicates important information and tips that help you make better use of your computer system. CAUTION: This icon indicate[...]

Product Information Product Features • Technical Specifications • Resolution & Preset Modes • Philips Pixel Defect Policy • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views • Attention Signals Product Features 170B 17" color LCD monitor with excellent display performance. ● Dual input-accep[...]

• Video dot rate 135MHz • Input impedance - Video 75 ohm - Sync 2 KOhm • Input signal levels 0.7 Vpp • Sync input signal Separate sync Composite sync Sync on green • Sync polarities Positive and negative • Video interface Dual input : Both Analog (D-Sub) and DVI-D (Digital) are available and user selectable. Optical characteristics • [...]

H. freq (KHz) Resolution V. freq (KHz) 31.5 640*350 70 31.5 720*400 70 31.5 640*480 60 35.0 640*480 67 37.5 640*480 75 35.2 800*600 56 37.9 800*600 60 46.9 800*600 75 49.7 832*624 75 48.4 1024*768 60 60 1024*768 75 69.0 1152*870 75 71.8 1152*900 76 63.9 1280*1024 60 80 1280*1024 75 RETURN TO TOP OF THE PAGE Automatic Power Saving If you have VESA&a[...]

OFF Blanked No No < 3W Amber This monitor is E NERGY S TAR ® compliant. A s an E NERGY S TAR ® P artner, PHILIPS has determined that this product meets the E NERGY S TAR ® guidelines for energy efficiency. RETURN TO TOP OF THE PAGE Physical Specifications • Dimension (WxHxD) 446 x 471x 181 mm (incl. Pedestal) • Weight 8.0 Kg • Tilt / Sw[...]

5 T.M.D.S. Data4+ 13 T.M.D.S. Data3+ 21 T.M.D.S. Data5+ 6 DDC Clock 14 +5V Power 22 T.M.D.S. Clock Shield 7 DDC Data 15 Ground (for +5V) 23 T.M.D.S. Clock+ 8 No connect 16 Hot Plug Detect 24 T.M.D.S. Clock- 2. The 15-pin D-sub connector (male) of the signal cable: Pin No. Assignment Pin No. Assignment 1 Red video input 9 +5V power 2 Green video inp[...]

Front View Product Description Attention Signals Attention signal display information and alerts about the status of the monitor. CANNOT DISPLAY THIS VIDEO MODE, CHANGE COMPUTER DISPLAY INPUT TO 1024X768 @ 60Hz or 1. CANNOT DISPLAY THIS VIDEO MODE, CHANGE COMPUTER DISPLAY INPUT TO 1280x1024 @ 60Hz -- This warning appears when the input signal from [...]

-- This message appears when there is no signal input. Solution : Make sure interface and power cables are properly connected. CHECK CABLE CONNECTION 3. -- This message appears when a signal cable is disconnected while computer is working. Solution : Re-connect signal input cables. ENTERING SLEEP MODE 4. -- This message appears when monitor is abou[...]

-- This message is displayed when the auto adjustment button is pressed. It disappears when automatic adjustments are completed. USE 1024X768 FOR BEST RESULT or 6. USE 1280X1024 FOR BEST RESULT -- One of these messages will show up at the top of the OSD main menu when the video signal input mode is not the recommended one. solution : For best perfo[...]

or MUTE OFF These signals appear to indicate audio status after the mute button has been pressed. SECOND VIDEO IS NOT AVAILABLE 8. -- This message appears when a user selects a second unavailable video source from the OSD from the INPUT SIGNAL SELECTION menu. -- On systems with both analog and digital output, this screen may appear when a signal ot[...]

--This message is displayed when a picture's size is manually extended to the largest screen display size with same video aspect ratio as the original picture. Picture size can continue to be enlarged up to full screen size, but its aspect ratio will be distorted. Message appears on 17" and 18" LCD monitors when a user attempts to st[...]

Installing your LCD Monitor Your LCD Monitor : Front View Product Description • Connecting to Your PC • Getting Started • Optimizing Performance Accessories (optional) : Installing the USB Hub • Installing the Protective Cover • Installing the Wall Mount Kit Front View UP and DOWN buttons are used when adjusting the OSD of your monitor In[...]

LEFT and RIGHT buttons, like the UP and DOWN buttons, are also used in adjusting the OSD of your monitor. BRIGHTNESS hotkey. When the UP and DOWN arrow buttons are pressed, the adjustment controls for the BRIGHTNESS will show up. .OK button which when pressed will take you to the OSD controls POWER button switches your monitor on Automatically adju[...]

On-Screen Display Description of the On-Screen Display • The OSD Tree • The OSD Controls Description of the On Screen Display What is the On-Screen Display? This is a feature in all Philips LCD monitors which allows an end-user to adjust screen performance of monitors directly though an on-screen instruction window. The user interface provides [...]

RETURN TO TOP OF THE PAGE The OSD Tree Below is an overall view of the structure of the On-Screen Display. You can use this as reference when you want to later on work your way around the different adjustments. On-Screen Display file:///D|/Philips LCD/english/170B/OSD/OSDDESC.HTM (2 of 5) [1/20/2001 3:17:05 PM][...]

On-Screen Display file:///D|/Philips LCD/english/170B/OSD/OSDDESC.HTM (3 of 5) [1/20/2001 3:17:05 PM][...]

RETURN TO TOP OF THE PAGE On-Screen Display file:///D|/Philips LCD/english/170B/OSD/OSDDESC.HTM (4 of 5) [1/20/2001 3:17:05 PM][...]

On-Screen Display file:///D|/Philips LCD/english/170B/OSD/OSDDESC.HTM (5 of 5) [1/20/2001 3:17:05 PM][...]

Customer Care & Warranty PLEASE SELECT YOUR COUNTRY/AREA TO REVIEW DETAILS OF YOUR WARRANTY COVERAGE WESTERN EUROPE: Austria • Belgium • Cyprus • Denmark • France • Germany • Greece • Finland • Ireland • Italy • Luxembourg • the Netherlands • Norway • Portugal • Sweden • Switzerland • Spain • United Kingdom EAS[...]

Glossary A B C D E F G H I J K L M N O P Q R S T U V W X Y Z B BNC connection A bayonet-locking connector slim coaxial cables. The connection is used in some monitors with high horizontal scanning frequencies. It provides optimum shielding between the video input signal lines to give the best possible video performance. RETURN TO TOP OF THE PAGE C [...]

RETURN TO TOP OF THE PAGE D D-SUB USB Your monitor comes with a D-Sub cable. Digital Visual Interface (DVI) The Digital Visual Interface (DVI) specification provides a high-speed digital connection for visual data types that is display technology independent. The interface is primarily focused at providing a connection between a computer and its di[...]

L LCD Liquid Crystal Display An alphanumeric display using the unique properties of liquid crystal to form characters. The latest flat-panel displays comprise a matrix of hundreds or thousands of individual LCD cells that generate text and colorful graphics on a screen. They consume little power though they do require external lighting to make them[...]

its ports. Device A logical or physical entity that performs a function. The actual entity described depends on the context of the reference. At the lowest level, device may refer to a single hardware component, as in a memory device. At a higher level, it may refer to a collection of hardware components that perform a particular function, such as [...]

RETURN TO TOP OF THE PAGE Glossary file:///D|/Philips LCD/english/170B/GLOSSARY/GLOSSARY.HTM (5 of 5) [1/20/2001 3:17:10 PM][...]

Download and Print Download and Printing Instructions • Installing FPadjust Program This page provides an option to read the manual in .pdf format. PDF files can be downloaded into your hard disk, then viewed and printed with Acrobat Reader or through your browser. If you do not have Adobe¨ Acrobat Reader installed, click on the link to install [...]

Printing instructions: To print the manual: 1. With the manual file open, follow your printer's instructions and print the pages you need. RETURN TO TOP OF THE PAGE Installing FPadjust Program The FP Adjust program generates alignment patterns which will help you adjust monitor settings such as CONTRAST, BRIGHTNESS, HORIZONTAL & VERTICAL P[...]

FAQs (Frequently Asked Questions) Safety and Troubleshooting • General FAQ • Screen Adjustments • Compatibility with Other Peripherals • LCD Panel Technology • Ergonomics, Ecology, and Safety Standards • Troubleshooting • Regulatory Information • Other Related Information General FAQs Q: When I install my monitor how do I do if the [...]

A: Your video card/graphic driver and monitor together determine the available resolutions. You can select desired resolution under Window 95/98 with the "Display properties/Settings" control panel Q: What if I get lost when making monitor adjustments? A: Simply press the OSD button, then select "Reset" to recall all original se[...]

Q: How should I clean the LCD surface? A: For normal cleaning, use the clean, soft and fine. For extensive cleaning, please use Isopropyl alcohol. Do not use other solvents such as ethyl alcohol, ethanol, acetone, hexane, etc. Q: What accessories are available for my 150P / 180P/ 170B LCD monitor? A: Currently there are 3 accessories available for [...]

Screen Adjustments Q: What is CustoMax® and what models are compatible? (181AS / 150P) A: CustoMax® is proprietary Philips software that allows users to adjust monitor via software instead of control keys under Windows base. With the Philips Brilliance 150P, CustoMax® operates via a USB connection to PC. All Philips 150P models are CustoMax® co[...]

Q: How can I adjust the screen? A: The screen brightness may be adjusted using the Brightness control in the OSD. Scaling an image in this manner results in slight brightness "fuzziness" or distortion. RETURN TO TOP OF THE PAGE Compatibility with other Peripherals Q: Can I connect my LCD monitor to any PC, workstation or Mac? A: Yes, all [...]

RETURN TO TOP OF THE PAGE LCD Panel Technology Q: What is Liquid Crystal Display? A: A Liquid Crystal Display (LCD) is an optical device that is commonly used to display ASCII characters and images on digital items such as watches, calculators, portable game consoles etc. LCD is the technology used for displays in notebook and other small computers[...]

Q: How does a TFT LCD Panel work? A: On each column and row of the TFT LCD panel, a data source drive and a gate drive and attached respectively. The TFT drain of each cell is connected to the electrode. The molecular arrangement of liquid crystal elements differs depending on whether it is impressed with voltage or not. It varies the direction of [...]

Q: Why is there no flicker on an LCD Monitor? A: Technically speaking, LCDs do flicker, but the cause of the phenomenon is different from that of CRT monitor -- and has no impact of ease of viewing. Flickering in a LCD monitor refers to usually undetectable luminance caused by the difference between positive and negative voltage. On the other hand,[...]

RETURN TO TOP OF THE PAGE FAQs (Frequently Asked Questions) file:///D|/Philips LCD/english/170B/SAFETY/SAF_FAQ.HTM (9 of 9) [1/20/2001 3:17:25 PM][...]

Troubleshooting Safety and Troubleshooting • FAQs • Common Problems • Imaging Problems • Regulatory Information • Other Related Information This page presents problems that can be corrected by the user. If the problem still exists after these possible solutions, contact your nearest Philips dealer. Common Problems Having this problem? Che[...]

AUTO button not working properly The Auto Function is designed for use on standard Macintosh or IBM-compatible PC running Microsoft properly Windows. ● It may not work properly if using non-standard PCs or video card. ● Imaging Problems Display position is incorrect Push the Auto button. ● Adjust the image position using the Horizontal Positi[...]

An after-image appears If an image remains in the screen for an extended period of time, it may be imprinted in the screen and leave an after-image. This usually disappears after a few hours ● An after-image remains after the power has been turned off. This is characteristic of liquid crystal and is not caused by a malfunction or deterioration of[...]

Regulatory Information TCO '99 Information • TCO Environmental Requirements • Energy Star Declaration • Federal Communications Commission (FCC) Notice (U.S. Only) • Commission Federale de la Communication (FCC Declaration) • EN 55022 Compliance (Czech Republic Only) • VCCI Class 2 Notice (Japan Only) • MOC Notice (South Korea Onl[...]

Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are[...]

A s an E NERGY S TAR ® P artner, PHILIPS has determined that this product meets the E NERGY S TAR ® guidelines for energy efficiency. We recommend you switch off the monitor when it is not in use for quite a long time. RETURN TO TOP OF THE PAGE Federal Communications Commission (FCC) Notice (U.S. Only) This equipment has been tested and found to [...]

RETURN TO TOP OF THE PAGE EN 55022 Compliance (Czech Republic Only) RETURN TO TOP OF THE PAGE VCCI Notice (Japan Only) This is a Class B product based on the standard of the Voluntary Control Council for Interference (VCCI) for Information technology equipment. If this equipment is used near a radio or television receiver in a domestic environment,[...]

The phasing conductor of the room's electrical installation should have a reserve short-circuit protection device in the form of a fuse with a nominal value no larger than 16 amperes (A). To completely switch off the equipment, the power supply cable must be removed from the power supply socket, which should be located near the equipment and e[...]

RETURN TO TOP OF THE PAGE BCIQ Notice (Taiwan Only) RETURN TO TOP OF THE PAGE Ergonomie Hinweis (nur Deutschland) Der von uns gelieferte Farbmonitor entspricht den in der "Verordnung über den Schutz vor Schäden durch Röntgenstrahlen" festgelegten Vorschriften. Auf der Rückwand des Gerätes befindet sich ein Aufkleber, der auf die Unbe[...]

3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate 3-pin plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5A. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5A. Note: The severed plug mus[...]

Other Related Information Safety and Troubleshooting • FAQs • Troubleshooting • Regulatory Information • Information for Users in the U. S . • Information for Users Outside the U.S Information for Users in the U. S. For units set at 115 V : Use a UL Listed Cord Set consisting of a minimum 18 AWG, Type SVT or SJT three conductor cord a max[...]

Philips Pixel Defect Policy Product Features • Technical Specifications • Resolution & Preset Modes • Automatic Power Saving • Physical Specification • Pin Assignment • Product Views Philips' Flat Panel Monitors Pixel Defect Policy Philips strives to deliver the highest quality products. We use some of the industry's most [...]

One lit red, green or blue subpixel Two adjacent lit subpixels: - Red + Blue = Purple - Red + Green = Yellow - Green + Blue = Cyan (Light Blue) Three adjacent lit subpixels (one white pixel) Black Dot Defects Black dot defects appear as pixels or subpixels that are always dark or "off". These are the types of black dot defects: One dark s[...]

RETURN TO TOP OF THE PAGE Philips Pixel Defect Policy file:///D|/Philips LCD/english/170B/PRODUCT/PIXEL.HTM (3 of 3) [1/20/2001 3:17:42 PM][...]

Connecting to Your PC Your LCD Monitor : Front View Product Description • Accessory Pack • Connecting to Your PC • Getting Started • Optimizing Performance Accessories (optional) : Installing the USB Hub • Installing the Protective Cover • Installing the Wall Mount Kit Accessory Pack Unpack all the parts. 1) Power Cable (socket may diff[...]

4) E-DFU package with Quick Setup Guide, Using Your Monitor Manual, and CD-ROM. RETURN TO TOP OF THE PAGE Connecting to Your PC Connecting to Your PC file:///D|/Philips LCD/english/170B/INSTALL/CONNECT.HTM (2 of 6) [1/20/2001 3:17:48 PM][...]

1) To remove the back cover, press up to disengage the clips on each side, then pull and lift. 2) Remove the plastic ring from the hinge Connecting to Your PC file:///D|/Philips LCD/english/170B/INSTALL/CONNECT.HTM (3 of 6) [1/20/2001 3:17:48 PM][...]

3) Plug in the video cable into VGA or DVI-D connector. 4) Cover the cables with the plastic ring and put the ring back on the hinge NOTE: If you use an Apple Macintosh™, you need to connect the special Mac adapter to one end of the monitor signal cable Connecting to Your PC file:///D|/Philips LCD/english/170B/INSTALL/CONNECT.HTM (4 of 6) [1/20/2[...]

5) Replace the back cover on the monitor Connecting to Your PC file:///D|/Philips LCD/english/170B/INSTALL/CONNECT.HTM (5 of 6) [1/20/2001 3:17:48 PM][...]

6) Connect to Your PC 6.1 Turn off your computer and unplug its power cable. 6.2 Connect the monitor signal cable to the video connector on the back of your computer. 6.3 Plug the power cord of your computer and your monitor into a nearby outlet. 6.4 Turn on your computer and monitor. If the monitor displays an image, installation is complete. RETU[...]

Getting Started Your LCD Monitor : Front View Product Description • Connecting to Your PC • Getting Started • Optimizing Performance Accessories (optional) : Installing the USB Hub • Installing the Protective Cover • Installing the Wall Mount Kit Getting Started 1.1 First turn on your monitor and other peripherals if any, then turn on you[...]

Installing Your USB Hub Your LCD Monitor : Front View Product Description • Connecting to Your PC • Getting Started • Optimizing Performance Accessories (optional) : Description of the USB Hub • Application • Installing the USB Hub • Installing the Protective Cover • Installing the Wall Mount Kit Description of the USB Hub USB Hub sup[...]

RETURN TO TOP OF THE PAGE Application Just a few peripherals you can connect to your USB Hub . Installing Your USB Hub file:///D|/Philips LCD/english/170B/INSTALL/USBHUB/USB_INST.HTM (2 of 4) [1/20/2001 3:17:48 PM][...]

1) Keyboard 2) Mouse 3) Joystick / Gamepad 4) Scanner 5) Printer 6) Phone / PBX RETURN TO TOP OF THE PAGE Installing Your USB Hub System requirements Hardware: A PC which supports the USB function and has a USB connector. Software: Windows system which supports USB (OSR2.1 or higher). Installation of USB Hub 1. Turn off the monitor and unplug the p[...]

4. Fix the USB Hub to the monitor by screwing 5. Do not tighten the fixing nut excessively (use fingers to tighten screws). If screwed too tight, the unit may not connect properly! 6. Plug-in the power cord and turn on the monitor. 7. The two ends of USB cable attached are different. Plug in the square end into the "upstream" connector of[...]

Installing the Protective Cover Your LCD Monitor : Front View Product Description • Connecting to Your PC • Getting Started • Optimizing Performance Accessories (optional) : Installing the USB Hub • Installing the Protective Cover • Cleaning Instructions • Installing the Wall Mount Kit Installing the Protective Cover 1) Locate the recta[...]

2) Pull up and forward to remove the front bezel from the monitor. 3) Peel off the film on both sides of the protective cover. Installing the Protective Cover file:///D|/Philips LCD/english/170B/INSTALL/P_COVER/pcov_inst.htm (2 of 4) [1/20/2001 3:17:49 PM][...]

4) Clip the protective cover onto the monitor, engaging only the top two clips. Now press the bottom corners of the protective cover to engage the two side clips. RETURN TO TOP OF THE PAGE Cleaning Instructions The anti-scratch, anti-reflective cover protects the LCD screen . Installing the Protective Cover file:///D|/Philips LCD/english/170B/INSTA[...]

Cleaning Instructions: Wipe with a soft dry cloth ● Do not use alcohol solvents or other strong chemical ● RETURN TO TOP OF THE PAGE Installing the Protective Cover file:///D|/Philips LCD/english/170B/INSTALL/P_COVER/pcov_inst.htm (4 of 4) [1/20/2001 3:17:49 PM][...]

Installing Your Wall Mount Kit Your LCD Monitor : Front View Product Description • Connecting to Your PC • Getting Started • Optimizing Performance Accessories (optional) : Installing the USB Hub • Installing the Protective Cover • Installing the Wall Mount Kit Installing the Wall Mount Kit 1) Please turn off the monitor and unplug all ca[...]

2) Detach the monitor base by pulling away the two parts. 3) Fix the mount bracket to the desired location. Installing Your Wall Mount Kit file:///D|/Philips LCD/english/170B/INSTALL/M_KIT/mkit_inst.htm (2 of 4) [1/20/2001 3:17:50 PM][...]

4) Thread all cables through the hole at the bottom of the bracket and use the clip provided to hold them in place. 5) Slide the support pin at the bottom of the monitor into the matching hole on the bracket, making sure that the pin is aligned. Then use the original base screw to securely fix the monitor to the bracket. Installing Your Wall Mount [...]

6) Connect the AC power adaptor provided to the DC-IN cable, and connect all other cables to the computer. RETURN TO TOP OF THE PAGE Installing Your Wall Mount Kit file:///D|/Philips LCD/english/170B/INSTALL/M_KIT/mkit_inst.htm (4 of 4) [1/20/2001 3:17:50 PM][...]

The OSD Controls Description of the On-Screen Display • The OSD Tree The OSD Controls : Brightness (HotKey) • Language • Adjust Position • Adjust size • Brightness and Contrast • Image Optimization • Adjust Color • OSD Settings • Product Information • Reset to Factory Settings • Input Selection • Exit Main Controls BRIGHTNES[...]

LANGUAGE The ON SCREEN DISPLAY prompts can be in one of six languages. The default language is English, but you can select French, Spanish, German, Italian, or Japanese. 1) Press the button on the monitor. The MAIN CONTROLS window appears. LANGUAGE is highlighted. (If not, press the or button on the monitor until LANGUAGE is highlighted) 2) Press t[...]

Smart Help Smart Help After returning to MAIN CONTROLS… … to continue to ADJUST POSITION, press the button until ADJUST POSITION is highlighted. Next, follow steps 3 - 6 under ADJUST POSITION. … to exit completely, press the button. RETURN TO TOP OF THE PAGE ADJUST POSITION ADJUST POSITION is composed of two steps, ADJUST HORIZONTAL and ADJUS[...]

3) Press the button. The ADJUST POSITION window appears. ADJUST HORIZONTAL is highlighted. 4) Press the or button to move the image left or right until it appears centered. 5) Press the button until ADJUST VERTICAL is highlighted. Press the or button to move the image up or down until it appears centered. 6) Press the button to confirm your selecti[...]

RETURN TO TOP OF THE PAGE ADJUST SIZE ADJUST SIZE allows you to adjust screen size when the input video mode in under 1280x1024. It has 3 options, FULL SCREEN, NATIVE MODE, and USER SETTINGS. 1). Press the button on the monitor, The MAIN CONTROLS window appears. LANGUAGE is highlighted. 2). Press the button until ADJUST SIZE is highlighted. 3). Pre[...]

selection and return to the MAIN CONTROLS window. EXIT MAIN CONTROLS is highlighted. 6a) If USER SETTINGS is highlighted, press the or button to adjust the screen size. 6b) When adjustment is complete, press the button to confirm your adjustment and return to the MAIN CONTROLS window. EXIT MAIN CONTROLS is highlighted. Smart Help Smart Help After r[...]

3) Press the button. The BRIGHTNESS & CONTRAST window appears. BRIGHTNESS is highlighted. 4) Press the or button to adjust the brightness. An 80% brightness is recommended. 5) When finished with BRIGHTNESS, press the button until CONTRAST is highlighted. Next, press the or button to adjust the contrast. A 100% contrast is recommended. The OSD C[...]

6) Press the button to confirm your selection and return to the MAIN CONTROLS window. EXIT MAIN CONTROLS is highlighted. Smart Help Smart Help After returning to MAIN CONTROLS… … to continue to IMAGE OPTIMIZATION, press the button until IMAGE OPTIMIZATION is highlighted. Next, follow steps 3 - 6 under IMAGE OPTIMIZATION. … to exit completely,[...]

3). Press the button. The IMAGE OPTIMIZATION window appears. VIDEO NOISE is highlighted. 4). Press or button to select PHASE, CLOCK and TEXT/GRAPHICS. 5). Once you have highlighted PHASE, CLOCK or TEXT/GRAPHICS, press the or button to adjust them. 6) When adjustment is complete, press the button to confirm your adjustment and return to the MAIN CON[...]

Smart Help Smart Help After returning to MAIN CONTROLS… … to continue to ADJUST COLOR, press the button until ADJUST COLOR is highlighted. Next, start with step 3 under ADJUST COLOR and follow the directions. … to exit completely, press the button. RETURN TO TOP OF THE PAGE ADJUST COLOR Your monitor has three preset options you can choose fro[...]

4) Press the or button to select ORIGINAL PANEL COLOR, 9300K FOR CAD/CAM USE, 6500K FOR IMAGE MANAGEMENT, or USER PRESET. 5) Once you have highlighted ORIGINAL PANEL COLOR, 9300K FOR CAD/CAM USE, or 6500K FOR IMAGE MANAGEMENT, press the button to confirm your selection and return to the MAIN CONTROLS window. EXIT MAIN CONTROLS is highlighted. The O[...]

6a) If USER PRESET is highlighted, press the button to highlight RED. Next, press the or button to adjust the color red. 6b) When finished with RED, press the button to highlight GREEN. Next, press the or button to adjust the color green. 6c) When finished with GREEN, press the button to highlight BLUE. Next, press the or button to adjust the color[...]

… to exit completely, press the button. RETURN TO TOP OF THE PAGE OSD SETTINGS You can place the main controls window almost any place on the screen that is convenient for you. OSD SETTING allows you to do this. It is composed of HORIZONTAL and VERTICAL adjustments you can make by simply following the step below. 1). Press the button on the monit[...]

4). Press the or button to move the MAIN CONTROLS window left or right to the desired position. 5). Press the button until VERTICAL is highlighted. Press the or button to move the MAIN CONTROLS window up or down to the desired position. 6). Press the button to confirm your selections and return to the MAIN CONTROLS window. EXIT MAIN CONTROLS is hig[...]

RETURN TO TOP OF THE PAGE PRODUCT INFORMATION The PRODUCT INFORMATION window displays the monitor's serial number, and the resolution of the monitor, all in one easy place. This is an information window only. Nothing can be adjusted in this window. To view this information, simply follow the steps below. 1) Press the button on the monitor. The[...]

Smart Help Smart Help After returning to MAIN CONTROLS… … to continue to RESET TO FACTORY SETTINGS, press the button until RESET TO FACTORY SETTINGS is highlighted. Next, start with step 3 under RESET TO FACTORY SETTINGS and follow the directions. … to exit completely, press the button. RETURN TO TOP OF THE PAGE RESET TO FACTORY SETTINGS RESE[...]

4) Press the or button to select YES or NO. NO is the default. YES returns all settings to their original factory adjustments. 5) Press the button to confirm your selections and return to the MAIN CONTROLS window. EXIT MAIN CONTROLS is highlighted. Smart Help Smart Help After returning to MAIN CONTROLS… … to continue to INPUT SELECTION, press t[...]

3) Press the button. The INPUT SELECTION window appears. 4) Press the or button to select either ANALOG or DIGITAL. 5) Press the button to confirm your selections and return to the MAIN CONTROLS window. CLOSE MAIN CONTROLS is highlighted. Smart Help Smart Help After returning to MAIN CONTROLS… … to exit completely, press the button. RETURN TO T[...]

Exit Main Controls RETURN TO TOP OF THE PAGE The OSD Controls file:///D|/Philips LCD/english/170B/OSD/OSD_CONT.HTM (19 of 19) [1/20/2001 3:18:00 PM][...]

Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while installing or using this product, please contact Philips directly[...]

Your International Guarantee Dear Customer, Thank you for purchasing this Philips product which has been designed and manufactured to the highest quality standards. If, unfortunately, something should go wrong with this product Philips guarantees free of charge labor and replacement parts irrespective of the country where it is repaired during a pe[...]

LIMITED WARRANTY (Computer Monitor) Three Years Free Labor / Three Years Free Service on Parts / One Year Exchange* *Product will be exchanged with a new or renewed to original specifications unit within two business days for the first year. This product must be shipped in at your expense for service during years two and three. WHO IS COVERED? You [...]

Philips service organization will attempt to provide service (although there may be a delay if the appropriate spare parts and technical manual(s) are not readily available). Where CAN I GET MORE INFORMATION? For more information, contact the Philips Customer Care Center by calling (800) 835-3506 (U.S.A. customers only) or (423) 475-0280 . Before R[...]

Philips Customer Care Center, P. O. Box 2976, Longview, TX 75601 Your International Philips F1rst Choice Warranty Thank you for purchasing this Philips monitor. All Philips monitors are designed and manufactured to high standards and deliver high-quality performance, ease of use and ease of installation. Should you encounter any difficulties while [...]