Texas Instruments TMS320C6452 DSP manuel d'utilisation

TMS320C6452 DSP DDR2 Memory Controller User's Guide Literature Number: SPRUF85 October 2007[...]

2 SPRUF85 – October 2007 Submit Documentation Feedback[...]

Contents Preface ............................................................................................................................... 6 1 Introduction ................................................................................................................ 9 1.1 Purpose of the Peripheral ...........................................[...]

List of Figures 1 DDR2 Memory Controller Block Diagram ............................................................................... 10 2 DDR2 Memory Controller Signals ........................................................................................ 12 3 DDR2 MRS and EMRS Command ...........................................................[...]

List of Tables 1 DDR2 Memory Controller Signal Descriptions ......................................................................... 12 2 DDR2 SDRAM Commands ............................................................................................... 13 3 Truth Table for DDR2 SDRAM Commands ......................................................[...]

Preface SPRUF85 – October 2007 Read This First About This Manual This document describes the operation of the DDR2 Memory Controller in the TMS320C6452. Notational Conventions This document uses the following conventions. • Hexadecimal numbers are shown with the suffix h. For example, the following number is 40 hexadecimal (decimal 64): 40h. ?[...]

www.ti.com Related Documents From Texas Instruments SPRUF87 — TMS320C6452 DSP Host Port Interface (UHPI) User's Guide describes the host port interface (HPI) in the TMS320C6452 Digital Signal Processor (DSP). The HPI is a parallel port through which a host processor can directly access the CPU memory space. The host device functions as a mas[...]

www.ti.com Related Documents From Texas Instruments SPRUF97 — TMS320C6452 DSP 3 Port Switch (3PSW) Ethernet Subsystem User's Guide describes the operation of the 3 port switch (3PSW) ethernet subsystem in the TMS320C6452 Digital Signal Processor (DSP). The 3 port switch gigabit ethernet subsystem provides ethernet packet communication and ca[...]

1 Introduction 1.1 Purpose of the Peripheral 1.2 Features 1.3 Functional Block Diagram User's Guide SPRUF85 – October 2007 DSP DDR2 Memory Controller This document describes the DDR2 memory controller in the device. The DDR2 memory controller is used to interface with JESD79D-2A standard compliant DDR2 SDRAM devices. Memory types such as DDR[...]

www.ti.com L1 S1 M1 D1 Data path A Register file A Register file B D2 Data path B S2 M2 L2 L1 data memory controller Cache control Memory protection Interrupt and exception controller Power control Instruction decode 16/32−bit instruction dispatch Instruction fetch SPLOOP buf fer C64x+ CPU IDMA Bandwidth management Cache control L1 program memory[...]

www.ti.com 2 Peripheral Architecture 2.1 Clock Control 2.2 Memory Map 2.3 Signal Descriptions Peripheral Architecture The DDR2 memory controller can gluelessly interface to most standard DDR2 SDRAM devices and supports such features as self-refresh mode and prioritized refresh. In addition, it provides flexibility through programmable parameters su[...]

www.ti.com DDR_D[31:0] DDR2 memory controller DDR_CLK DDR_CLK DDR_CS DDR_CKE DDR_RAS DDR_WE DDR_DQM[3:0] DDR_CAS DDR_BA[2:0] DDR_DQS[3:0] DDR_A[13:0] DDR_VREF DDR_DQGA TE[3:0] DDR_DQS[3:0] DDR_ODT[1:0] Peripheral Architecture Figure 2. DDR2 Memory Controller Signals Table 1. DDR2 Memory Controller Signal Descriptions Pin Description DDR_D[31:0] Bid[...]

www.ti.com 2.4 Protocol Description(s) Peripheral Architecture The DDR2 memory controller supports the DDR2 SDRAM commands listed in Table 2 . Table 3 shows the signal truth table for the DDR2 SDRAM commands. Table 2. DDR2 SDRAM Commands Command Function ACTV Activates the selected bank and row. DCAB Precharge all command. Deactivates (precharges) [...]

www.ti.com 2.4.1 Mode Register Set (MRS and EMRS) COL MRS/EMRS BANK DDR_CLK DDR_CLK DDR_CS DDR_CKE DDR_RAS DDR_WE DDR_CAS DDR_BA[2:0] DDR_A[13:0] 2.4.2 Refresh Mode Peripheral Architecture DDR2 SDRAM contains mode and extended mode registers that configure the DDR2 memory for operation. These registers control burst type, burst length, CAS latency,[...]

www.ti.com REFR DDR_CLK DDR_CLK DDR_CS DDR_CKE DDR_RAS DDR_WE DDR_DQM[3:0] DDR_CAS DDR_BA[2:0] DDR_A[13:0] 2.4.3 Activation (ACTV) ACTV BANK ROW DDR_CLK DDR_CLK DDR_CS DDR_CKE DDR_RAS DDR_WE DDR_DQM[3:0] DDR_CAS DDR_BA[2:0] DDR_A[13:0] Peripheral Architecture Figure 4. Refresh Command The DDR2 memory controller automatically issues the activate (AC[...]

www.ti.com 2.4.4 Deactivation (DCAB and DEAC) DCAB DDR_CLK DDR_CLK DDR_CS DDR_CKE DDR_RAS DDR_WE DDR_DQM[3:0] DDR_CAS DDR_BA[2:0] DDR_A[13:1 1, 9:0] DDR_A[10] DEAC DDR_CLK DDR_CLK DDR_CS DDR_CKE DDR_RAS DDR_WE DDR_DQM[3:0] DDR_CAS DDR_BA[2:0] DDR_A[13:1 1, 9:0] DDR_A[10] Peripheral Architecture The precharge all banks command (DCAB) is performed af[...]

www.ti.com 2.4.5 READ Command DDR_D[31:0] DDR_DQS[3:0] COL BANK DDR_A[10] CAS Latency D0 D1 D2 D3 D4 D5 D6 D7 DDR_CLK DDR_CLK DDR_CS DDR_CKE DDR_RAS DDR_WE DDR_DQM[3:0] DDR_CAS DDR_BA[2:0] DDR_A[13:0] Peripheral Architecture Figure 8 shows the DDR2 memory controller performing a read burst from DDR2 SDRAM. The READ command initiates a burst read op[...]

www.ti.com 2.4.6 Write (WRT) Command DDR_D[31:0] DDR_DQS[3:0] COL BANK DQM7 Sample D0 D1 D2 D3 D4 D5 D6 D7 DQM1 DQM2 DQM3 DQM4 DQM5 DQM6 DQM8 Write Latency DDR_A[10] DDR_CLK DDR_CLK DDR_CS DDR_CKE DDR_RAS DDR_WE DDR_DQM[3:0] DDR_CAS DDR_BA[2:0] DDR_A[13:0] 2.5 Memory Width and Byte Alignment Peripheral Architecture Prior to a WRT command, the desir[...]

www.ti.com DDR2 memory controller data bus DDR_D[31:24] (Byte Lane 3) DDR_D[23:16] (Byte Lane 2) DDR_D[15:8] (Byte Lane 1) DDR_D[7:0] (Byte Lane 0) 32-bit memory device 16-bit memory device 2.6 Address Mapping Peripheral Architecture Figure 10 shows the byte lanes used on the DDR2 memory controller. The external memory is always right aligned on th[...]

www.ti.com Peripheral Architecture SDCFG Bit Logical Address IBANK PAGESIZE 31:28 27 26 25 24 23 22:17 16 15 14 13 12 11 10 9:2 0 0 X X X X X nrb=14 (1) ncb=8 1 0 X X X X nrb=14 nbb=1 ncb=8 2 0 X X X nrb=14 nbb=2 ncb=8 3 0 X X nrb=14 nbb=3 ncb=8 0 1 X X X X nrb=14 ncb=9 1 1 X X X nrb=14 nbb=1 ncb=9 2 1 X X nrb=14 nbb=2 ncb=9 3 1 X nrb=14 nbb=3 ncb=[...]

www.ti.com Col. 0 Col. 1 Col. 2 Col. 3 Col. 4 Col. M−1 Col. M Row 0, bank 0 Row 0, bank 1 Row 0, bank 2 Row 0, bank P Row 1, bank 1 Row 1, bank 0 Row 1, bank 2 Row 1, bank P Row N, bank 2 Row N, bank 1 Row N, bank 0 Row N, bank P Peripheral Architecture Figure 11 shows how the DSP memory map is partitioned into columns, rows, and banks. Note that[...]

www.ti.com 0 1 2 3 M Bank 0 Row 0 Row 1 Row 2 Row N C o l l C o l C o l C o Row 0 Row N Row 1 Row 2 C C Bank 1 l l 0 2 1 o o C C l l 3 M o o Row 0 Row N Row 1 Row 2 C C Bank 2 l l 0 2 1 o o l l l l Row N Row 2 Row 0 Row 1 Bank P 0123 M C C l l 3 M o o o C o C o C o C 2.7 DDR2 Memory Controller Interface Peripheral Architecture Figure 14. DDR2 SDRAM[...]

www.ti.com Command/Data Scheduler Command FIFO W rite FIFO Read FIFO Registers Command to Memory W rite Data to Memory Read Data from Memory Command Data EDMA BUS 2.7.1 Command Ordering and Scheduling, Advanced Concept Peripheral Architecture Figure 15. DDR2 Memory Controller FIFO Block Diagram The DDR2 memory controller performs command re-orderin[...]

www.ti.com 2.7.2 Command Starvation Peripheral Architecture Next, the DDR2 memory controller examines each of the commands selected by the individual masters and performs the following reordering: • Among all pending reads, selects reads to rows already open. Among all pending writes, selects writes to rows already open. • Selects the highest p[...]

www.ti.com 2.7.3 Possible Race Condition 2.8 Refresh Scheduling Peripheral Architecture A race condition may exist when certain masters write data to the DDR2 memory controller. For example, if master A passes a software message via a buffer in DDR2 memory and does not wait for indication that the write completes, when master B attempts to read the[...]

www.ti.com 2.9 Self-Refresh Mode 2.10 Reset Considerations Hard resetfrom PLLCTL1 DDR PSC DDR2 memory controller registers State machine VRST VCTL_RST Peripheral Architecture Setting the self refresh (SR) bit in the SDRAM refresh control register (SDRFC) to 1 forces the DDR2 memory controller to place the external DDR2 SDRAM in a low-power mode [...]

www.ti.com 2.11 DDR2 SDRAM Memory Initialization 2.11.1 DDR2 SDRAM Device Mode Register Configuration Values Peripheral Architecture DDR2 SDRAM devices contain mode and extended mode registers that configure the mode of operation for the device. These registers control parameters such as burst type, burst length, and CAS latency. The DDR2 memory co[...]

www.ti.com 2.11.2 DDR2 SDRAM Initialization After Reset 2.11.3 DDR2 SDRAM Initialization After Register Configuration 2.12 Interrupt Support 2.13 EDMA Event Support 2.14 Emulation Considerations Peripheral Architecture Table 10. DDR2 SDRAM Extended Mode Register 1 Configuration (continued) Mode Mode Register Register Bit Field Init Value Descriptio[...]

www.ti.com 3 Using the DDR2 Memory Controller 3.1 Connecting the DDR2 Memory Controller to DDR2 SDRAM Using the DDR2 Memory Controller The following sections show various ways to connect the DDR2 memory controller to DDR2 memory devices. The steps required to configure the DDR2 memory controller for external memory access are also described. Figure[...]

www.ti.com CK CK CKE CS WE RAS CAS LDM UDM LDQS UDQS BA[2:0] A[12:0] DQ[15:0] VREF DDR2 memory x16−bit LDQS UDQS DDR_CLK DDR_CLK DDR_CKE DDR_CS DDR_WE DDR_RAS DDR_DQM0 DDR_CAS DDR_DQM1 DDR_DQS0 DDR_DQS0 DDR_DQS1 DDR_DQS1 DDR_BA[2:0] DDR_A[13:0] DDR_D[15:0] DDR_DQM2 DDR_DQM3 DDR_DQS2 DDR_DQS3 DDR_D[31:16] DDR_DQGA TE0 (A) DDR2 memory controller OD[...]

www.ti.com DDR_CLK DDR_CLK DDR_CKE DDR_CS DDR_WE DDR_RAS DDR_CAS DDR_DQM0 DDR_DQM1 DDR_DQS0 DDR_DQS1 DDR_BA[2:0] DDR_A[13:0] DDR_D[15:0] DDR_VREF DDR_ODT0 DDR_DQS0 DDR_DQS1 CK CK CKE CS WE RAS CAS LDM UDM LDQS UDQS BA[2:0] A[12:0] DQ[15:0] ODT VREF LDQS UDQS DDR2 memory x16−bit VREF DDR2 memory controller DDR_ODT1 DDR_DQGA TE0 (A) DDR_DQGA TE1 (A[...]

www.ti.com CK CK CKE CS WE RAS CAS DM DQS BA[2:0] A[13:0] DQ[7:0] VREF DDR2 memory x8−bit DQS RDQS DDR_CLK DDR_CLK DDR_CKE DDR_CS DDR_WE DDR_RAS DDR_DQM0 DDR_CAS DDR_DQS0 DDR_DQS0 DDR_BA[2:0] DDR_A[13:0] DDR_D[7:0] DDR_DQM1 DDR_DQS1 DDR_D[15:8] DDR_VREF DDR2 memory controller ODT DDR_ODT0 DDR_ODT1 DDR_DQS1 memory x8−bit DQS A[13:0] VREF ODT DQ[[...]

www.ti.com 3.2 Configuring DDR2 Memory Controller Registers to Meet DDR2 SDRAM Specifications 3.2.1 Programming the SDRAM Configuration Register (SDCFG) 3.2.2 Programming the SDRAM Refresh Control Register (SDRFC) Using the DDR2 Memory Controller The DDR2 memory controller allows a high degree of programmability for shaping DDR2 accesses. This prov[...]

www.ti.com 3.2.3 Configuring SDRAM Timing Registers (SDTIM1 and SDTIM2) Using the DDR2 Memory Controller Table 12 displays the DDR2-533 refresh rate specification. Table 12. DDR2 Memory Refresh Specification Symbol Description Value t REF Average Periodic Refresh Interval 7.8 μ s Therefore, the value for the REFRESH-RATE can be calculated as follo[...]

www.ti.com 3.2.4 Configuring the DDR2 Memory Controller Control Register (DMCCTL) Using the DDR2 Memory Controller Table 15. SDTIM2 Configuration DDR2 SDRAM Data Register Field Sheet Parameter Data Sheet Formula (Register Field Name Name Description Value Field Must Be ≥ ) Value T_ODT t AOND t AOND specifies the ODT 2 (t CK cycles) CAS latency - [...]

www.ti.com 4 DDR2 Memory Controller Registers DDR2 Memory Controller Registers Table 17 lists the memory-mapped registers for the DDR2 memory controller. See the device-specific data manual for the memory address of these registers. Table 17. DDR2 Memory Controller Registers Offset Acronym Register Description Section 00h MIDR Module ID and Revisio[...]

www.ti.com 4.1 Module ID and Revision Register (MIDR) 4.2 DDR2 Memory Controller Status Register (DMCSTAT) DDR2 Memory Controller Registers The Module ID and Revision register (MIDR) is shown in Figure 20 and described in Table 18 . Figure 20. Module ID and Revision Register (MIDR) 31 30 29 16 Reserved MOD_ID R-0x0 R-0x0031 15 8 7 0 MJ_REV MN_REV R[...]

www.ti.com 4.3 SDRAM Configuration Register (SDCFG) DDR2 Memory Controller Registers The SDRAM configuration register (SDCFG) contains fields that program the DDR2 memory controller to meet the specification of the DDR2 memory. These fields configure the DDR2 memory controller to match the data bus width, CAS latency, number of internal banks, and [...]

www.ti.com DDR2 Memory Controller Registers Table 20. SDRAM Configuration Register (SDCFG) Field Descriptions (continued) Bit Field Value Description 11-9 CL CAS latency. The value of this field defines the CAS latency, to be used when accessing connected SDRAM devices. A write to this field will cause the DDR2 Memory Controller to start the SDRAM [...]

www.ti.com 4.4 SDRAM Refresh Control Register (SDRFC) DDR2 Memory Controller Registers The SDRAM refresh control register (SDRFC) is used to configure the DDR2 memory controller to: • Enter and Exit the self-refresh state. • Meet the refresh requirement of the attached DDR2 device by programming the rate at which the DDR2 memory controller issu[...]

www.ti.com 4.5 SDRAM Timing 1 Register (SDTIM1) DDR2 Memory Controller Registers The SDRAM timing 1 register (SDTIM1) configures the DDR2 memory controller to meet many of the AC timing specification of the DDR2 memory. Note that DDR_CLK is equal to the period of the DDR_CLK signal. See the DDR2 memory data sheet for information on the appropriate [...]

www.ti.com DDR2 Memory Controller Registers Table 22. SDRAM Timing 1 Register (SDTIM1) Field Descriptions (continued) Bit Field Value Description 1-0 T_WTR These bits specify the minimum number of DDR_CLK cycles from the last write to a read command, minus 1. The value for these bits can be derived from the t wtr AC timing parameter in the DDR2 mem[...]

www.ti.com 4.6 SDRAM Timing 2 Register (SDTIM2) DDR2 Memory Controller Registers Like the SDRAM timing 1 register (SDTIM1), the SDRAM timing 2 register (SDTIM2) also configures the DDR2 memory controller to meet the AC timing specification of the DDR2 memory. See the DDR2 memory data sheet for information on the appropriate values to program each f[...]

www.ti.com 4.7 Burst Priority Register (BPRIO) DDR2 Memory Controller Registers The Burst Priority Register (BPRIO) helps prevent command starvation within the DDR2 memory controller. To avoid command starvation, the DDR2 memory controller momentarily raises the priority of the oldest command in the command FIFO after a set number of transfers have[...]

www.ti.com 4.8 DDR2 Memory Controller Control Register (DMCCTL) DDR2 Memory Controller Registers The DDR2 memory controller control register (DMCCTL) resets the interface logic of the DDR2 memory controller. The DMCCTL is shown in Figure 27 and described in Table 25 . Figure 27. DDR2 Memory Controller Control Register (DMCCTL) 31 16 Reserved R-0x50[...]

IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders[...]