English dropdown-ico

hussman ESSS-0303 manual

1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24

Go to page of

Similar user manuals

A good user manual

The rules should oblige the seller to give the purchaser an operating instrucion of hussman ESSS-0303, along with an item. The lack of an instruction or false information given to customer shall constitute grounds to apply for a complaint because of nonconformity of goods with the contract. In accordance with the law, a customer can receive an instruction in non-paper form; lately graphic and electronic forms of the manuals, as well as instructional videos have been majorly used. A necessary precondition for this is the unmistakable, legible character of an instruction.

What is an instruction?

The term originates from the Latin word „instructio”, which means organizing. Therefore, in an instruction of hussman ESSS-0303 one could find a process description. An instruction's purpose is to teach, to ease the start-up and an item's use or performance of certain activities. An instruction is a compilation of information about an item/a service, it is a clue.

Unfortunately, only a few customers devote their time to read an instruction of hussman ESSS-0303. A good user manual introduces us to a number of additional functionalities of the purchased item, and also helps us to avoid the formation of most of the defects.

What should a perfect user manual contain?

First and foremost, an user manual of hussman ESSS-0303 should contain:
- informations concerning technical data of hussman ESSS-0303
- name of the manufacturer and a year of construction of the hussman ESSS-0303 item
- rules of operation, control and maintenance of the hussman ESSS-0303 item
- safety signs and mark certificates which confirm compatibility with appropriate standards

Why don't we read the manuals?

Usually it results from the lack of time and certainty about functionalities of purchased items. Unfortunately, networking and start-up of hussman ESSS-0303 alone are not enough. An instruction contains a number of clues concerning respective functionalities, safety rules, maintenance methods (what means should be used), eventual defects of hussman ESSS-0303, and methods of problem resolution. Eventually, when one still can't find the answer to his problems, he will be directed to the hussman service. Lately animated manuals and instructional videos are quite popular among customers. These kinds of user manuals are effective; they assure that a customer will familiarize himself with the whole material, and won't skip complicated, technical information of hussman ESSS-0303.

Why one should read the manuals?

It is mostly in the manuals where we will find the details concerning construction and possibility of the hussman ESSS-0303 item, and its use of respective accessory, as well as information concerning all the functions and facilities.

After a successful purchase of an item one should find a moment and get to know with every part of an instruction. Currently the manuals are carefully prearranged and translated, so they could be fully understood by its users. The manuals will serve as an informational aid.

Table of contents for the manual

  • Page 1

    /Chino ESSS / ESS Self Ser vice Match ESC / ESCS Re v .0303 Installation & Operation Manual ESSS / ESS Self Ser vice Cases (Match ESC / ESCS) p/n IGSS-ESSS / ESS-0303 INST ALLA TION & O PE RA T IO N GUIDE[...]

  • Page 2

    IGSS-ESS/ESSS-0303 2 /Chino A publication of Hussmann ® Chino 13770 Ramona A v enue • Chino , California 91710 (909) 628-8942 F AX (909) 590-4910 (800) 395-9229 K eep this booklet with the case at all times f or futur e refer ence . THIS BOOKLET CONT AINS INFORMA TION ON: ESSS: Refrigerated Self Service cases Matc hes Multidec k Ser- vice Cases [...]

  • Page 3

    Rev.0 303 3 Cut & Plan Vie ws ESSS 8" CASE FRONT 8" DRAIN AND ELECTRICAL MECHANICAL STUB UP AREA 18" X 18" REFRIG. MECHANICAL STUB UP AREA 18" X 18" ESS (ESSS) Plan View Scale = 1/4" 8'-2" (V ARIABLE LENGTHS) 1" 1" 43 5 / 8 " (49 1 / 4 " / 46 3 / 4 ") ESS Self-Service Scale =[...]

  • Page 4

    IGSS-ESS/ESSS-0303 4 LOCA TION The refrigerated mer chandisers hav e been designed for use only in air conditioned stor es where temperatur e and humidity ar e maintained at or below 75°F and 55% rela- tive humidity . DO NO T allow air conditioning, electric fans, ov ens, open doors or windows (etc .) to cr eate air cur - r ents ar ound the mercha[...]

  • Page 5

    Rev.0 303 5 Do not use cam locks to pull cases together. 2. Secur e joint backer . Located behind cart bumper supor t at joints. T o adjust scr ews holding bumper cart to case on either side or the joint and slide extrusion to center of joint. This piece suppor ts the forn t panel at the joint. 3. Apply bead of silicone to top of bulkheads. 4. Slip[...]

  • Page 6

    IGSS-ESS/ESSS-0303 6 Plumbing WASTE OUTLET AND P-TRAP The waste outlet is located off the center of the case on one side allowing drip piping to be run lengthwise under the fixture. A 1-1/2" P-trap and thr eaded adapter ar e supplied with each fixture. The P-trap must be installed to pr ev ent air leakage and insect entrance into the fixtur e [...]

  • Page 7

    Rev.0 303 7 Refrigeration REFRIGERANT TYPE The standard r efrigerant will be R-22 unless otherwise specified on the customer or der . Check the serial plate on the case for inf ormation. PIPING The refrigerant line outlets ar e located under the case . Locate first the electrical box, the outlets are then on the same side of the case but at the opp[...]

  • Page 8

    IGSS-ESS/ESSS-0303 8 Electrical WIRING COLOR CODE GREEN GROUND PURPLE ANTI-SWEA T ORANGE LIGHTS YELLO W RECEPT ACLE RED / BLACK T -ST A T /SOLENOID 230V BLACK / WHITE T - S TAT / S O L E N O I D 115V BRO WN F AN MO T ORS CASE MUST BE GROUNDED NOTE: Refer to label affixed to case to determine the actual configuration as checked in the “TYPE INSTAL[...]

  • Page 9

    Rev.0 303 9 User Information Joi n t Tr i m ESSS Only (ESS dows not ha ve joint trim) CAMLOCK & SEALANT LOCA TIONS CAMLO CK AC CESS PA N E L APPL Y SEALANT TO S H ADED AREA JOINT BACKER LOCA TION CAMLOCK L OCA TI ON S SEAL AROUND PIPING ACCESS HOLES BOL T INSIDE WEDGES CAMLOCK L OCA TI ON STOCKING Improper temperatur e and lighting will cause s[...]

  • Page 10

    IGSS-ESS/ESSS-0303 10 deh ydration pr ocess. The only other moistur e within the case is that in the pr oduct itself. A single lev el of meat will dr y out faster than a fully loaded case of 3–4 lev els of meat. IMPOR T ANT STEPS 1. Do not set temperatur e too cold, as this causes pr oduct deh ydration. Product T emperature: 33°–35°! Set ther[...]

  • Page 11

    Rev.0 303 11 attracts dust and dirt to the surface . Blotting with a clean damp cloth is recommended to r emove charge. ANTIST A TIC CO A TINGS F or acrylic used indoors, antistatic coatings successfully pre v ent the accumulation of an electr ostatic charge for periods of sev eral months—if the surface is not washed or wiped down with a w et clo[...]

  • Page 12

    IGSS-ESS/ESSS-0303 12 Maintenance ELECTRICAL PRECAUTIONS BEFORE SERVICING – Always disconnect electrical power at the main disconnect when servicing or replacing any electrical component This includes (but not limited to) Fans, Heaters, Thermostats, and Lights. REPLACING FLUORESCENT LAMPS Fluorescent lamps ar e furnished with moisture r esistant [...]

  • Page 13

    Rev.0 303 13 Specifications NOTES: These refrigerated merchandisers have been designed for use in stores where temperatures and humidity are maintained at or below 75°F and 55%RH. Stores are responsible for setting their cases approprately in conditions which vary from the above. The number of defrosts and/or the duration may vary for cases displa[...]

  • Page 14

    IGSS-ESS/ESSS-0303 14 Electrical Schematics Light Switch Overhead Canopy Lights Ledge Light (Optional) Ballats WH3-120-164 (125-04-0118) Thermostat Suction Solenoid Duplex Receptacles GFCI Dedicated Line Evaporator Fan Cap Case to Case Harness Single case Pigtail F17T8-SPX30 (2) 125-04-0101 125-04-0110 125-04-0111 125-04-0113 125-04- 0113 125-04- 0[...]

  • Page 15

    Rev.0 303 15 Light Switch Front Lights (optional) Ledge Lights (optional) Ballast WH3-120-164 (125-04-0118) Thermostat Liquid Solenoid Duplex Receptacles GFCI Dedicated Line Ballast Extension Box (Switched Power) Evaporator Fans Cap Case to Case Harness Single case Pigtail F32T8-SPX30 (2) 125-04-0103 125-04-0101 125-04-0108 125-04-0110 125-04-0111 [...]

  • Page 16

    IGSS-ESS/ESSS-0303 16 Light Switch Front Lights Ledge Lights (Optional) Ballast WH3-120-164 (125-04-0118) Thermostat Liquid Solenoid Duplex Receptacles GFCI Dedicated Line Ballast Extension Box (Switched Power) Evaporator Fans Cap Case to Case Harness Single case Pigtail F25T8-SPX30 (2) Plenum extension Evaporator Fans 125-04-0104 125-04-0101 125-0[...]

  • Page 17

    Rev.0 303 17 Light Switch Front Lights Ledge Lights (Optional) Ballast WH3-120-164 (125-04-0118) Thermostat Liquid Solenoid Duplex Receptacles GFCI Dedicated Line Ballast Extension Box (Switched Power) Evaporator Fans Cap Case to Case Harness Single case Pigtail F32T8-SPX30 (2) Plenum extension Evaporator Fans 125-04-0105 125-04-0101 125-04-0108 12[...]

  • Page 18

    IGSS-ESS/ESSS-0303 18 Light Switch Front Lights Ledge Lights (Optional) Ballasts WH3-120-164 (125-04-0118) Thermostat Liquid Solenoid F32T8-SPX30 (1) Duplex Receptacles GFCI Dedicated Line Ballast Extension Box (Switched Power) Evaporator Fans Cap Case to Case Harness Single case Pigtail F25T8-SPX30 (2) Plenum extension Evaporator Fans Plenum exten[...]

  • Page 19

    Rev.0 303 19 Light Switch Front Lights Ledge Lights (Optional) Ballasts WH3-120-164 (125-04-0118) Thermostat Liquid Solenoid F32T8-SPX30 (1) Duplex Receptacles GFCI Dedicated Line Ballast Extension Box (Switched Power) Evaporator Fans Cap Case to Case Harness Single case Pigtail F32T8-SPX30 (2) Plenum extension Evaporator Fans Plenum extension Evap[...]

  • Page 20

    IGSS-ESS/ESSS-0303 20 APPENDIX A. – Temperature Guidlines The refrigerators should be operated according to the manufacturer’s published engineering specifications for entering air temperatures for specific equipment applications. Table 1 shows the typical temperature of the air entering the food zone one hour before the start of defrost and on[...]

  • Page 21

    Rev.0 303 21 only in Fahrenheit shall be accurate to 2°F. The thermometer should be checked for proper calibration. (It should read 32°F when the stem is immersed in an ice water bath). b) LOCATION – The probe or sensing element of the thermometer should be located in the airstream where the air first enters the display or storage area, and not[...]

  • Page 22

    IGSS-ESS/ESSS-0303 22[...]

  • Page 23

    Rev.0 303 23 Limited W arranty This warranty is made to the original user at the original installation site and is not transf erable . Hussmann merchandisers ar e war ranted to be free fr om def ect in material and workmanship under normal use and ser vice for a period of one (1) y ear fr om the date of original installation (not to exceed fifteen [...]

  • Page 24

    IGSS-ESS/ESSS-0303 24 The MODEL NAME and SERIAL NUMBER is required in or der to pr ovide you with the correct parts and information for y our particular unit. They can be found on a small metal plate on the unit. Please note them below for futur e refer ence . MODEL: SERIAL NUMBER: /Chino Additional copies of this publication may be obtained b y co[...]