Jenn-Air JGC7430 инструкция обслуживания

S EALED GA S cooro p s [ I " JENN-AIR J ENN-AI R CCG2423AND CCG2523 F_ JGC7430 AND JGC7536 4 0 3 W E ST I NS TALLATIO N M ANUA L IMPORTANT: D imensions Shown in Both Inches andCentimeters. IMPO R TANT: Besure the applian c e being installed is equipped for the g a s to be supplied . Refer to seri al plate onunderside of burner box for this inf[...]

LOCATION OF YOUR JE N N-AIR APPUA N CE PREPARATIO N OFCOUNTERTOP Loc at e t h i s appl i anc e away f ro m co m bust i b l e m ater i a ls su c h a s w indo w Th e c o unt e r top cutout mu st b e p re p a red a cco r d i ng t o t he i ll us trat i o n on curt ai ns and com bust i b l e w all de co rations, page 1 of these in st ructions . Min i mu[...]

I N STALLATIO N OF APPLIA N CE CO NN ECTI N G APPLIANCE TO GAS SUPPLY The installation of this appliance mu st con f o r m with local codes o r , inthe A TRAINED SERVICEMAN OR GA S APPLIANCE INSTALLER MUST absen ce o f loc al codas , w i th the National Fuel Gas Code,ANSI MAKETHEGASSUPPLY C ONNECTION.L ea kt as tingoltheapplian ce Z223 . 1 - L at e[...]

2 . IF THIS IS A 30 " WIDE C OOKTOP AND A JENN -N R, MODEL W3 0 XXX OR W131, ELECTRIC WALL O V EN IS T O BE INSTALLED BELOW THIS COOKT O R NOTE 1:This appliance a n d its g a s and el e ctr i cal supp l y sources m ust b e installed before the wall oven is in sta lled, See illu st ratio n ( E lectrical Wiring ILLUSTRAT N E GAS SUPPLY PIPING tn[...]

ALTERNATIVE PIPING METHODS TO CONNECT APPUANCE TO GA S SUPPLY A TRAINED SERVICEMAN OR GAS APPLIANCE INSTALLER MUST CAU11 ON: Donot _ e m pt to at tach t heflexible connecto r di r ectly to an MAKETHE GAS SUPPLY CONNECTION.Le a kI as ting of th e appliance e xt er n al pi pe thr ead. Co nn ec tion r eq uires flare union a dap t ers . shall be c ondu[...]

E L ECTRICA L WIRING INFORMATION T his appl i ance i se q u i pp e d wi th a grounde d type pow er cord. A grou n ded an d, i f n ecess a r y, thr ou gh t h e sla t s s u pp ort in g the s he l f . Th e c le ar an ce out l et m ust b e provided. It is reco mm ended, f or conve ni ence , the outlet be hole shou l d be located a snear as practical to[...]

CONVERTING APPLIA N CE FOR USE I N STALLATION OFLP ORIFICE SPUDS WITH LP GAS 4 BURNER MODEL (30 " WIDE) WARNING P ropa ne conv e rsion is to be p e r f or m ed by a J E NN-AI R A UT HORI ZE D SERVICER (or other q uali f ied age n cy) in a ccordance witht h e m an u facturer's instructions and all codes andr e q uire m ents o f the authori[...]

B . I n ve rt m p I n app l ian c e pre sa ure regu l ator ( See fig ur es 10 and 1 1. ) 3 . In s e r t a s le n d er, thin - b l a d e scre wd riv e r int o th e r e c e ss a t c ent e r o f W ith th e applia n ce i n s talled, th e applience re g ulato r s ho uld b e locat e d v a l v e st er n end engag e b l a d e w i t h slotin a d just i ng s[...]

TOCONVERT APPLIANCE FOR USE WITH I N STALLATIO N OF N ATURAL GAS NATURAL GAS ORIFICE SPUDS WARNING I 4 BURNER MODEL J Electrical power and ga s must be turned off prior to conversion. If this applian c e has been converted foruse withL P gas, ea c h of the following modifications m ust be perfor m ed to c onve rt the unit back to n atural g a s. A.[...]

BUR N ER IG N ITIO N ANDAUTO-REIGNITIO N TOP GRATE REPLACEMENT T h i sappl i anc e i s equipped forelec t ron i c a ut o- rai g n it i on b y m eans o f a The to p g rates on t hi s co ok to p ha v e u nd e r si de p ro jec tio n l ug s d e sig ned sp a r k ig n i t er l oca t e d a t the r e ar of ea ch b urn e r . Th e bur n e r s a r e designed [...]