Makita 6710D инструкция обслуживания

Cordless Screwdriver Wood screws Machine screws MODEL 6710D MODEL 6710DW With Fast Charger weight speed length Nuts INSTRUCTION MANUAL 5 1 mm x 50 mm 11.4' x2'l I SPECIFICATIONS 6 mm 6 mm 220 195 mm 1 1 kg f 114") (1/4") Rimin 17-518") 12.4 lhsl Model 67100 Battery Cartridge 7000 Model OC7100 Fast charger 72V Dimensions iL [...]

IMPORTANT SAFETY INSTRUCTIONS (For All Tools) WARNING: WHEN USING ELECTRIC TOOLS, BASIC SAFE- REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, AND PER- TY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED TO SONAL INJURY, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS. 1. 2. 3. 4. 5. 6. 7. 8. 9. IO. 11. 12. 13. 2 KEEP WORK AREA CLEAN. Cluttered areas and benches invit[...]

14. 15. 16. 17. 18. 19. 20. REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turn- ing it on. AVOID UNINTENTIONAL STARTING. Don't carry plugged-in tool with finger on switch. Be sure switch is OFF when plugging in. OUTDOOR USE EXTENSION CORDS. When tool is used outd[...]

IMPORTANT SAFETY INSTRUCTIONS Length of Cord (Feet) AWG Size of Cord I. SAVE THESE INSTRUCTIONS - This manual 25 50 100 150 18 18 18 16 contains important safety and operating instructions for battery charger. 2. Before using battery charger, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using ba[...]

ADDITIONAL SAFETY RULES FOR CHARGER & BATTERY CARTRIDGE 1. Do not charge Battery Cartridge when temperature is BELOW 10°C (SOOF) or ABOVE 4OoC (104OF). 2. Do not attempt to use a step-up transformer, an engine generator or DC power 3. Do not allow anything to cover or clog the charger vents. 4. Always cover the battery terminals with the batte[...]

Installing or removing battery cartridge 0 Always switch off the tool before insertion 0 To remove the battery cartridge, pull out the set plate on the tool and grasp both sides of the cartridge while withdrawing it from the barrel. .To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip i[...]

Switch action I Trigger switch I 0 Set the reversing switch lever just in front of the trigger switch to Forward (FWD) or Reverse (REV). Then pull the trigger to turn the tool ON and release it to turn it OFF. To change the direction of bit rotation, release the trigger, let the tool come to a complete stop, and then slide the switch lever to the o[...]

Fastening torque adjustment I 0 The fastening torque may be adjusted by turning the adjustment ring to align the notched line on the ring with a number on the indicator label. However, the clearance between the ring and the cap is 2.5 mm (1/8") maximum after one full turn, and the ring should not be forced beyond this point. 0 Turning the adju[...]

Hole 0The hole on the heel of the tool is a con- venient way to carry it by a cord, hook or other means. Drill chuck (Accessory) 0 To install a drill chuck, remove the insert bit by a strong jerk, then a drill chuck can be replaced with the insert bit by a sharp push of the hand. .To install the drill bit, place it in the chuck as far as it will go[...]

Screwdriving Match your bit to your screw. Item I Rominal Diameter (mm) Phillips bits Select your screws meter with the chart Bit No. Wood Screw on and the nominal right. dia- )- 2.1 - 2.7 13/32'' - 118") No. 2 3.1 - 4.8 (1/8" - 3/16') No.3 1 5.1 (3/16") Slotted bits Select a slotted bit to match the slot on the screw [...]

MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELlABl LITY, repairs, maintenance and adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 11[...]

ACC ESSO R I ES #3 CAUTION: These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. 784215-0A - 0 Charger 12V for cer Model [...]

0 Battery holster Carrying case Steel case part N~, 823087-3 Plastic case Holster holds extra battery. Part No. 181428-2 Part No. 823033-3C 13[...]

Aug -09-'84 US CORDLESS SCREWDRIVER Model 67100 Note: The switch and other part configurations may differ from country to country. 14[...]

MODEL 67101D ’EM $&, DESCRIPTION Aug -0944 US ‘iM & DESCRIPTION MACHINE ~ 1 2 3 4 5 6 7 6 3 10 11 12 13 14 15 - 1 1 1 1 1 1 1 1 1 1 I 1 1 2 1 - Torque Adlust Ring 20 0 Ring 16 Guide Plate Lock Washer 14 F Washer 14 Leal sprang Sled Ball 3 5 Spindle P,n 4 Compression Spring 14 T Washer 10 Clutch Cam Steel Ball 6 4 Spur Gear 86 Cap MACHI[...]

MAKITA LIMITED ONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freigh[...]